Message-ID: <0ae5656f-20d7-95dc-f88a-7125edfbfb75@ti.com>
Date:   Tue, 17 Nov 2020 14:09:38 -0600
From:   Suman Anna <s-anna@...com>
To:     Grzegorz Jaszczyk <grzegorz.jaszczyk@...aro.org>,
        <ohad@...ery.com>, <bjorn.andersson@...aro.org>,
        <mathieu.poirier@...aro.org>
CC:     <linux-remoteproc@...r.kernel.org>, <robh+dt@...nel.org>,
        <lee.jones@...aro.org>, <devicetree@...r.kernel.org>,
        <linux-kernel@...r.kernel.org>, <linux-omap@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>, <praneeth@...com>,
        <rogerq@...com>
Subject: Re: [PATCH 5/6] remoteproc/pru: Add support for various PRU cores on
 K3 AM65x SoCs

Hi Greg,

On 11/14/20 2:46 AM, Grzegorz Jaszczyk wrote:
> From: Suman Anna <s-anna@...com>
> 
> The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
> processor subsystem, commonly referred to as ICSSG. Each ICSSG processor
> subsystem on AM65x SR1.0 contains two primary PRU cores and two new
> auxiliary PRU cores called RTUs. The AM65x SR2.0 SoCs have a revised
> ICSSG IP that is based off the subsequent IP revision used on J721E
> SoCs. This IP instance has two new custom auxiliary PRU cores called
> Transmit PRUs (Tx_PRUs) in addition to the existing PRUs and RTUs.
> 
> Each RTU and Tx_PRU cores have their own dedicated IRAM (smaller than
> a PRU), Control and debug feature sets, but is different in terms of
> sub-modules integrated around it and does not have the full capabilities
> associated with a PRU core. The RTU core is typically used to aid a
> PRU core in accelerating data transfers, while the Tx_PRU cores is
> normally used to control the TX L2 FIFO if enabled in Ethernet
> applications. Both can also be used to run independent applications.
> The RTU and Tx_PRU cores though share the same Data RAMs as the PRU
> cores, so the memories have to be partitioned carefully between different
> applications. The new cores also support a new sub-module called Task
> Manager to support two different context thread executions.
> 
> Enhance the existing PRU remoteproc driver to support these new PRU, RTU
> and Tx PRU cores by using specific compatibles. The initial names for the
> firmware images for each PRU core are retrieved from DT nodes, and can
> be adjusted through sysfs if required.
> 
> The PRU remoteproc driver has to be specifically modified to use a
> custom memcpy function within its ELF loader implementation for these
> new cores in order to overcome a limitation with copying data into each
> of the core's IRAM memories. These memory ports support only 4-byte
> writes, and any sub-word order byte writes clear out the remaining
> bytes other than the bytes being written within the containing word.
> The default ARM64 memcpy also cannot be used as it throws an exception
> when the preferred 8-byte copy operation is attempted. This choice is
> made by using a state flag that is set only on K3 SoCs.
> 
> Signed-off-by: Suman Anna <s-anna@...com>
> Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@...aro.org>
> Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@...aro.org>
> ---
>  drivers/remoteproc/pru_rproc.c | 141 ++++++++++++++++++++++++++++++---
>  1 file changed, 132 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
> index 33806ddcbd5d..04c9f07799e2 100644
> --- a/drivers/remoteproc/pru_rproc.c
> +++ b/drivers/remoteproc/pru_rproc.c
> @@ -46,9 +46,13 @@
>  #define PRU_DEBUG_GPREG(x)	(0x0000 + (x) * 4)
>  #define PRU_DEBUG_CT_REG(x)	(0x0080 + (x) * 4)
>  
> -/* PRU Core IRAM address masks */
> +/* PRU/RTU/Tx_PRU Core IRAM address masks */
>  #define PRU0_IRAM_ADDR_MASK	0x34000
>  #define PRU1_IRAM_ADDR_MASK	0x38000
> +#define RTU0_IRAM_ADDR_MASK	0x4000
> +#define RTU1_IRAM_ADDR_MASK	0x6000
> +#define TX_PRU0_IRAM_ADDR_MASK	0xa000
> +#define TX_PRU1_IRAM_ADDR_MASK	0xc000
>  
>  /* PRU device addresses for various type of PRU RAMs */
>  #define PRU_IRAM_DA	0	/* Instruction RAM */
> @@ -73,12 +77,38 @@ enum pru_iomem {
>  	PRU_IOMEM_MAX,
>  };
>  
> +/**
> + * enum pru_type - PRU core type identifier
> + *
> + * @PRU_TYPE_PRU: Programmable Real-time Unit
> + * @PRU_TYPE_RTU: Auxiliary Programmable Real-Time Unit
> + * @PRU_TYPE_TX_PRU: Transmit Programmable Real-Time Unit
> + * @PRU_TYPE_MAX: just keep this one at the end
> + */
> +enum pru_type {
> +	PRU_TYPE_PRU = 0,
> +	PRU_TYPE_RTU,
> +	PRU_TYPE_TX_PRU,
> +	PRU_TYPE_MAX,
> +};
> +
> +/**
> + * struct pru_private_data - device data for a PRU core
> + * @type: type of the PRU core (PRU, RTU, Tx_PRU)
> + * @is_k3: flag used to identify the need for special load & event handling
> + */
> +struct pru_private_data {
> +	enum pru_type type;
> +	unsigned int is_k3 : 1;
> +};
> +
>  /**
>   * struct pru_rproc - PRU remoteproc structure
>   * @id: id of the PRU core within the PRUSS
>   * @dev: PRU core device pointer
>   * @pruss: back-reference to parent PRUSS structure
>   * @rproc: remoteproc pointer for this PRU core
> + * @data: PRU core specific data
>   * @mem_regions: data for each of the PRU memory regions
>   * @fw_name: name of firmware image used during loading
>   * @mapped_irq: virtual interrupt numbers of created fw specific mapping
> @@ -93,6 +123,7 @@ struct pru_rproc {
>  	struct device *dev;
>  	struct pruss *pruss;
>  	struct rproc *rproc;
> +	const struct pru_private_data *data;
>  	struct pruss_mem_region mem_regions[PRU_IOMEM_MAX];
>  	const char *fw_name;
>  	int *mapped_irq;
> @@ -318,11 +349,12 @@ static int pru_rproc_start(struct rproc *rproc)
>  {
>  	struct device *dev = &rproc->dev;
>  	struct pru_rproc *pru = rproc->priv;
> +	const char *names[PRU_TYPE_MAX] = { "PRU", "RTU", "Tx_PRU" };
>  	u32 val;
>  	int ret;
>  
> -	dev_dbg(dev, "starting PRU%d: entry-point = 0x%llx\n",
> -		pru->id, (rproc->bootaddr >> 2));
> +	dev_dbg(dev, "starting %s%d: entry-point = 0x%llx\n",
> +		names[pru->data->type], pru->id, (rproc->bootaddr >> 2));
>  
>  	ret = pru_handle_intrmap(rproc);
>  	/*
> @@ -344,9 +376,10 @@ static int pru_rproc_stop(struct rproc *rproc)
>  {
>  	struct device *dev = &rproc->dev;
>  	struct pru_rproc *pru = rproc->priv;
> +	const char *names[PRU_TYPE_MAX] = { "PRU", "RTU", "Tx_PRU" };
>  	u32 val;
>  
> -	dev_dbg(dev, "stopping PRU%d\n", pru->id);
> +	dev_dbg(dev, "stopping %s%d\n", names[pru->data->type], pru->id);
>  
>  	val = pru_control_read_reg(pru, PRU_CTRL_CTRL);
>  	val &= ~CTRL_CTRL_EN;
> @@ -458,9 +491,53 @@ static struct rproc_ops pru_rproc_ops = {
>  	.da_to_va	= pru_rproc_da_to_va,
>  };
>  
> +/*
> + * Custom memory copy implementation for ICSSG PRU/RTU Cores

Please update this to add Tx_PRU as well to the list here and in the below
description.

> + *
> + * The ICSSG PRU/RTU cores have a memory copying issue with IRAM memories, that
> + * is not seen on previous generation SoCs. The data is reflected properly in
> + * the IRAM memories only for integer (4-byte) copies. Any unaligned copies
> + * result in all the other pre-existing bytes zeroed out within that 4-byte
> + * boundary, thereby resulting in wrong text/code in the IRAMs. Also, the
> + * IRAM memory port interface does not allow any 8-byte copies (as commonly
> + * used by ARM64 memcpy implementation) and throws an exception. The DRAM
> + * memory ports do not show this behavior. Use this custom copying function
> + * to properly load the PRU/RTU firmware images on all memories for simplicity.

This last line is obsolete now that we use regular memcpy for Data RAM copies.

regards
Suman

> + */
> +static int pru_rproc_memcpy(void *dest, const void *src, size_t count)
> +{
> +	const int *s = src;
> +	int *d = dest;
> +	int size = count / 4;
> +	int *tmp_src = NULL;
> +
> +	/*
> +	 * TODO: relax limitation of 4-byte aligned dest addresses and copy
> +	 * sizes
> +	 */
> +	if ((long)dest % 4 || count % 4)
> +		return -EINVAL;
> +
> +	/* src offsets in ELF firmware image can be non-aligned */
> +	if ((long)src % 4) {
> +		tmp_src = kmemdup(src, count, GFP_KERNEL);
> +		if (!tmp_src)
> +			return -ENOMEM;
> +		s = tmp_src;
> +	}
> +
> +	while (size--)
> +		*d++ = *s++;
> +
> +	kfree(tmp_src);
> +
> +	return 0;
> +}
> +
>  static int
>  pru_rproc_load_elf_segments(struct rproc *rproc, const struct firmware *fw)
>  {
> +	struct pru_rproc *pru = rproc->priv;
>  	struct device *dev = &rproc->dev;
>  	struct elf32_hdr *ehdr;
>  	struct elf32_phdr *phdr;
> @@ -512,7 +589,17 @@ pru_rproc_load_elf_segments(struct rproc *rproc, const struct firmware *fw)
>  		if (!phdr->p_filesz)
>  			continue;
>  
> -		memcpy(ptr, elf_data + phdr->p_offset, filesz);
> +		if (pru->data->is_k3 && is_iram) {
> +			ret = pru_rproc_memcpy(ptr, elf_data + phdr->p_offset,
> +					       filesz);
> +			if (ret) {
> +				dev_err(dev, "PRU memory copy failed for da 0x%x memsz 0x%x\n",
> +					da, memsz);
> +				break;
> +			}
> +		} else {
> +			memcpy(ptr, elf_data + phdr->p_offset, filesz);
> +		}
>  	}
>  
>  	return ret;
> @@ -619,9 +706,17 @@ static int pru_rproc_set_id(struct pru_rproc *pru)
>  	int ret = 0;
>  
>  	switch (pru->mem_regions[PRU_IOMEM_IRAM].pa & 0x3ffff) {
> +	case TX_PRU0_IRAM_ADDR_MASK:
> +		fallthrough;
> +	case RTU0_IRAM_ADDR_MASK:
> +		fallthrough;
>  	case PRU0_IRAM_ADDR_MASK:
>  		pru->id = 0;
>  		break;
> +	case TX_PRU1_IRAM_ADDR_MASK:
> +		fallthrough;
> +	case RTU1_IRAM_ADDR_MASK:
> +		fallthrough;
>  	case PRU1_IRAM_ADDR_MASK:
>  		pru->id = 1;
>  		break;
> @@ -642,8 +737,13 @@ static int pru_rproc_probe(struct platform_device *pdev)
>  	struct rproc *rproc = NULL;
>  	struct resource *res;
>  	int i, ret;
> +	const struct pru_private_data *data;
>  	const char *mem_names[PRU_IOMEM_MAX] = { "iram", "control", "debug" };
>  
> +	data = of_device_get_match_data(&pdev->dev);
> +	if (!data)
> +		return -ENODEV;
> +
>  	ret = of_property_read_string(np, "firmware-name", &fw_name);
>  	if (ret) {
>  		dev_err(dev, "unable to retrieve firmware-name %d\n", ret);
> @@ -676,6 +776,7 @@ static int pru_rproc_probe(struct platform_device *pdev)
>  
>  	pru = rproc->priv;
>  	pru->dev = dev;
> +	pru->data = data;
>  	pru->pruss = platform_get_drvdata(ppdev);
>  	pru->rproc = rproc;
>  	pru->fw_name = fw_name;
> @@ -727,11 +828,33 @@ static int pru_rproc_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> +static const struct pru_private_data pru_data = {
> +	.type = PRU_TYPE_PRU,
> +};
> +
> +static const struct pru_private_data k3_pru_data = {
> +	.type = PRU_TYPE_PRU,
> +	.is_k3 = 1,
> +};
> +
> +static const struct pru_private_data k3_rtu_data = {
> +	.type = PRU_TYPE_RTU,
> +	.is_k3 = 1,
> +};
> +
> +static const struct pru_private_data k3_tx_pru_data = {
> +	.type = PRU_TYPE_TX_PRU,
> +	.is_k3 = 1,
> +};
> +
>  static const struct of_device_id pru_rproc_match[] = {
> -	{ .compatible = "ti,am3356-pru", },
> -	{ .compatible = "ti,am4376-pru", },
> -	{ .compatible = "ti,am5728-pru", },
> -	{ .compatible = "ti,k2g-pru",    },
> +	{ .compatible = "ti,am3356-pru",	.data = &pru_data },
> +	{ .compatible = "ti,am4376-pru",	.data = &pru_data },
> +	{ .compatible = "ti,am5728-pru",	.data = &pru_data },
> +	{ .compatible = "ti,k2g-pru",		.data = &pru_data },
> +	{ .compatible = "ti,am654-pru",		.data = &k3_pru_data },
> +	{ .compatible = "ti,am654-rtu",		.data = &k3_rtu_data },
> +	{ .compatible = "ti,am654-tx-pru",	.data = &k3_tx_pru_data },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, pru_rproc_match);
> 

Powered by blists - more mailing lists