linux-kernel - [PATCH 0/3] drm/mipi-dbi: Type B bus support, drm/tiny: MRB2801

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <1605684945-29727-1-git-send-email-mikhail_durnev@mentor.com>
Date:   Wed, 18 Nov 2020 17:35:42 +1000
From:   mdurnev@...il.com
To:     linux-kernel@...r.kernel.org
Cc:     mikhail_durnev@...tor.com, dri-devel@...ts.freedesktop.org,
        noralf@...nnes.org
Subject: [PATCH 0/3] drm/mipi-dbi: Type B bus support, drm/tiny: MRB2801

From: Mikhail Durnev <mikhail_durnev@...tor.com>

Hi All,

This patch series is aiming at extending the mipi-dbi bus driver
to support Intel 8080 type parallel bus (Type B) over GPIO and
adding a new driver for ILI9341 display panels with 8- or 16-bit
parallel interface.

It was tested with the MRB2801 display module [1] that had
a connector compatible with the ALIENTEK STM32 development board.
The module was connected to Raspberry Pi 3 via GPIO pins.

The parallel bus is implemented partially. It supports only write
operations from the host to the display. Read operations would
require switching GPIO mode between input and output back and
forth. But this implementation is very simple, and GPIO mode can
be set for all used pins to output once at initialization.
The RD pin of the display has to always receive the logic high
signal to make sure the data bus pins from the dislay side are
always in the high impedance state. Otherwise the display module
as well as the GPIO controller of the host can be damaged.
To be on the safe side I recommend using protective resistors
for all GPIO pins conneced to DB pins of the display. Resistors
of 10 kOhms are just fine for RPi 3. The WR and DC pins may not
work well with 10K resistors. Although there is no need to protect
them, you can try using 1K resistors if you want.

Bit banging is used to transmit data over the parallel bus from
host to display. There are two numbers that contol timings. They
should be defined in the device tree via the wr-up-down-delays
property. The first number is related to the write control pulse
duration, and the second number is related to the write cycle
duration. For ILI9341, the write pulse cannot be shorter than 15 ns,
and the write duration cannot be shorter than 66 ns. Delays of
10 and 51 ns respectively allow to meet the specifications on
RPi 3. Faster machines may need values closer to 15 and 66.

[1] http://www.lcdwiki.com/2.8inch_16BIT_Module_ILI9341_SKU:MRB2801

Mikhail Durnev (3):
  drm/mipi-dbi: Add support for Type B
  drm/tiny: Add driver for ili9341 with parallel bus
  dt-bindings: panel: Add bindings for MRB2801

 .../devicetree/bindings/display/ronbo,mrb2801.txt  |  42 +++
 drivers/gpu/drm/drm_mipi_dbi.c                     | 116 ++++++++-
 drivers/gpu/drm/tiny/Kconfig                       |  13 +
 drivers/gpu/drm/tiny/Makefile                      |   1 +
 drivers/gpu/drm/tiny/ili9341_gpio.c                | 290 +++++++++++++++++++++
 include/drm/drm_mipi_dbi.h                         |  30 ++-
 6 files changed, 490 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/ronbo,mrb2801.txt
 create mode 100644 drivers/gpu/drm/tiny/ili9341_gpio.c

-- 
2.7.4