Message-ID: <20201224113727.GB15628@kozik-lap>
Date:   Thu, 24 Dec 2020 12:37:27 +0100
From:   Krzysztof Kozlowski <krzk@...nel.org>
To:     Tim Harvey <tharvey@...eworks.com>
Cc:     Rob Herring <robh+dt@...nel.org>, Shawn Guo <shawnguo@...nel.org>,
        Sascha Hauer <s.hauer@...gutronix.de>,
        Pengutronix Kernel Team <kernel@...gutronix.de>,
        Fabio Estevam <festevam@...il.com>,
        NXP Linux Team <linux-imx@....com>,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 2/2] arm64: dts: imx8mm: Add Gateworks IMX8MM Development
 Kits

On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote:
> The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development
> kits comprised of a GW700x SoM and a Baseboard.
> 
> The GW700x SoM contains:
>  - IMX8MM SoC

It's i.MX 8M Mini.
https://www.nxp.com/products/processors-and-microcontrollers/arm-processors/i-mx-applications-processors/i-mx-8-processors/i-mx-8m-mini-arm-cortex-a53-cortex-m4-audio-voice-video:i.MX8MMINI

>  - LPDDR4 DRAM
>  - eMMC FLASH
>  - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor)
>  - GbE PHY connected to the IMX8MM FEC
>  - Power Management IC
> 
> The GW71xx Baseboard contains:
>  - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM
>  - 1x RJ45 GbE (IMX8MM FEC)
>  - PCIe Clock generator
>  - GPS and accelerometer
>  - 1x USB 2.0 Front Panel connector
>  - wide range power supply
> 
> The GW72xx Baseboard contains:
>  - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM
>  - 2x RJ45 GbE (IMX8MM FEC and LAN743x)
>  - 1x MicroSD connector
>  - 1x USB 2.0 Front Panel connector
>  - 1x SPI connector
>  - PCIe Clock generator
>  - GPS and accelerometer
>  - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
>  - wide range power supply
> 
> The GW73xx Baseboard contains:
>  - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM
>  - 2x RJ45 GbE (IMX8MM FEC and LAN743x)
>  - 1x MicroSD connector
>  - 1x USB 2.0 Front Panel connector
>  - 1x SPI connector
>  - WiFi/BT
>  - PCIe Clock generator
>  - GPS and accelerometer
>  - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
>  - wide range power supply
> 
> Signed-off-by: Tim Harvey <tharvey@...eworks.com>
> ---
>  arch/arm64/boot/dts/freescale/Makefile             |   3 +
>  .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi   | 482 +++++++++++++++++++++
>  .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts |  19 +
>  .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi   | 186 ++++++++
>  .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts |  20 +
>  .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi   | 311 +++++++++++++
>  .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts |  19 +
>  .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi   | 363 ++++++++++++++++
>  8 files changed, 1403 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index f8d5943..ecdd233 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
> new file mode 100644
> index 00000000..7e1b96b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
> @@ -0,0 +1,482 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> +	memory@...00000 {
> +		device_type = "memory";
> +		reg = <0x0 0x40000000 0 0x80000000>;
> +	};
> +
> +	gpio_keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		user_pb {
> +			label = "user_pb";
> +			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
> +			linux,code = <BTN_0>;
> +		};
> +
> +		user_pb1x {
> +			label = "user_pb1x";
> +			linux,code = <BTN_1>;
> +			interrupt-parent = <&gsc>;
> +			interrupts = <0>;
> +		};
> +
> +		key_erased {
> +			label = "key-erased";

Above you use underscore, here hyphen. Make it consistent.

> +			linux,code = <BTN_2>;
> +			interrupt-parent = <&gsc>;
> +			interrupts = <1>;
> +		};
> +
> +		eeprom_wp {
> +			label = "eeprom_wp";
> +			linux,code = <BTN_3>;
> +			interrupt-parent = <&gsc>;
> +			interrupts = <2>;
> +		};
> +
> +		tamper {
> +			label = "tamper";
> +			linux,code = <BTN_4>;
> +			interrupt-parent = <&gsc>;
> +			interrupts = <5>;
> +		};
> +
> +		switch_hold {
> +			label = "switch_hold";
> +			linux,code = <BTN_5>;
> +			interrupt-parent = <&gsc>;
> +			interrupts = <7>;
> +		};
> +	};
> +};
> +
> +&A53_0 {
> +	cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_1 {
> +	cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_2 {
> +	cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_3 {
> +	cpu-supply = <&buck3_reg>;
> +};
> +
> +&ddrc {
> +	operating-points-v2 = <&ddrc_opp_table>;
> +
> +	ddrc_opp_table: opp-table {
> +		compatible = "operating-points-v2";
> +
> +		opp-25M {
> +			opp-hz = /bits/ 64 <25000000>;
> +		};
> +
> +		opp-100M {
> +			opp-hz = /bits/ 64 <100000000>;
> +		};
> +
> +		opp-750M {
> +			opp-hz = /bits/ 64 <750000000>;
> +		};
> +	};
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	gsc: gsc@20 {

Node name should describe class of a device so maybe
"system-controller"?

> +		compatible = "gw,gsc";
> +		reg = <0x20>;
> +		pinctrl-0 = <&pinctrl_gsc>;
> +		interrupt-parent = <&gpio2>;
> +		interrupts = <6 GPIO_ACTIVE_LOW>;

Wrong flag.

> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		adc {

Just to be sure - did you build it with W=1 to find any dtc warnings?

> +			compatible = "gw,gsc-adc";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			channel@6 {
> +				gw,mode = <0>;
> +				reg = <0x06>;
> +				label = "temp";
> +			};
> +
> +			channel@8 {
> +				gw,mode = <1>;
> +				reg = <0x08>;
> +				label = "vdd_bat";
> +			};
> +
> +			channel@16 {
> +				gw,mode = <4>;
> +				reg = <0x16>;
> +				label = "fan_tach";
> +			};
> +
> +			channel@82 {
> +				gw,mode = <2>;
> +				reg = <0x82>;
> +				label = "vdd_vin";
> +				gw,voltage-divider-ohms = <22100 1000>;
> +			};
> +
> +			channel@84 {
> +				gw,mode = <2>;
> +				reg = <0x84>;
> +				label = "vdd_adc1";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@86 {
> +				gw,mode = <2>;
> +				reg = <0x86>;
> +				label = "vdd_adc2";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@88 {
> +				gw,mode = <2>;
> +				reg = <0x88>;
> +				label = "vdd_dram";
> +			};
> +
> +			channel@8c {
> +				gw,mode = <2>;
> +				reg = <0x8c>;
> +				label = "vdd_1p2";
> +			};
> +
> +			channel@8e {
> +				gw,mode = <2>;
> +				reg = <0x8e>;
> +				label = "vdd_1p0";
> +			};
> +
> +			channel@90 {
> +				gw,mode = <2>;
> +				reg = <0x90>;
> +				label = "vdd_2p5";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@92 {
> +				gw,mode = <2>;
> +				reg = <0x92>;
> +				label = "vdd_3p3";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@98 {
> +				gw,mode = <2>;
> +				reg = <0x98>;
> +				label = "vdd_0p95";
> +			};
> +
> +			channel@9a {
> +				gw,mode = <2>;
> +				reg = <0x9a>;
> +				label = "vdd_1p8";
> +			};
> +
> +			channel@a2 {
> +				gw,mode = <2>;
> +				reg = <0xa2>;
> +				label = "vdd_gsc";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +		};
> +
> +		fan-controller@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;

These do not seem needed.

> +			compatible = "gw,gsc-fan";
> +			reg = <0x0a>;
> +		};
> +	};
> +
> +	gsc_gpio: pca9555@23 {

Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be
sure your board validate against dt-schema.

> +		compatible = "nxp,pca9555";
> +		reg = <0x23>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		interrupt-parent = <&gsc>;
> +		interrupts = <4>;
> +	};
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c02";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +
> +	eeprom@51 {
> +		compatible = "atmel,24c02";
> +		reg = <0x51>;
> +		pagesize = <16>;
> +	};
> +
> +	eeprom@52 {
> +		compatible = "atmel,24c32";
> +		reg = <0x52>;
> +		pagesize = <32>;
> +	};
> +
> +	eeprom@53 {
> +		compatible = "atmel,24c32";
> +		reg = <0x53>;
> +		pagesize = <32>;
> +	};
> +
> +	pmic@69 {
> +		compatible = "mps,mp5416";
> +		reg = <0x69>;
> +
> +		regulators {
> +			buck1 {
> +				regulator-name = "vdd_0p95";
> +				regulator-min-microvolt = <805000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-max-microamp = <2500000>;
> +				regulator-boot-on;
> +			};
> +
> +			buck2 {
> +				regulator-name = "vdd_soc";
> +				regulator-min-microvolt = <805000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-max-microamp = <1000000>;
> +				regulator-boot-on;
> +			};
> +
> +			buck3_reg: buck3 {
> +				regulator-name = "vdd_arm";
> +				regulator-min-microvolt = <805000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-max-microamp = <2200000>;
> +				regulator-boot-on;
> +			};
> +
> +			buck4 {
> +				regulator-name = "vdd_1p8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-max-microamp = <500000>;
> +				regulator-boot-on;
> +			};
> +
> +			ldo1 {
> +				regulator-name = "nvcc_snvs_1p8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-max-microamp = <300000>;
> +				regulator-boot-on;
> +			};
> +
> +			ldo2 {
> +				regulator-name = "vdd_snvs_0p8";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-boot-on;
> +			};
> +
> +			ldo3 {
> +				regulator-name = "vdd_0p95";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-boot-on;
> +			};
> +
> +			ldo4 {
> +				regulator-name = "vdd_1p8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +
> +	eeprom@52 {
> +		compatible = "atmel,24c32";
> +		reg = <0x52>;
> +		pagesize = <32>;
> +	};
> +};
> +
> +&uart2 { /* console */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +&usdhc3 { /* eMMC */
> +	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
> +	assigned-clock-rates = <400000000>;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
> +			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
> +			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
> +			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
> +			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
> +			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
> +			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
> +			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
> +			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
> +			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
> +			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
> +			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
> +			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
> +			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
> +			MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0			0x19
> +		>;
> +	};
> +
> +	pinctrl_gsc: gscirq {

grp suffix. I think dtbs_check should point this out.

> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6	0x159
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c3
> +			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
> +			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
> +			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x140
> +		>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x190
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d0
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d0
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d0
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d0
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d0
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d0
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d0
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d0
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d0
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x190
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {

Ditto

> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x194
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d4
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d4
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d4
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x194
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {

Ditto

> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x196
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d6
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d6
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d6
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d6
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d6
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d6
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d6
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d6
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d6
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x196
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
> new file mode 100644
> index 00000000..3f88c4a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
> @@ -0,0 +1,19 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm.dtsi"
> +#include "imx8mm-venice-gw700x.dtsi"
> +#include "imx8mm-venice-gw71xx.dtsi"
> +
> +/ {
> +	model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit";
> +	compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
> new file mode 100644
> index 00000000..a4eeb0d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi

This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy.

> @@ -0,0 +1,186 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/ {
> +	aliases {
> +		usb0 = &usbotg1;
> +		usb1 = &usbotg2;
> +	};
> +
> +	leds {

led-controller

> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		user1 { /* GRN */

led-0

> +			label = "user1";

label is now deprecated. See the common bindings.

> +			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		user2 { /* RED */

led-1

> +			label = "user2";
> +			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	pps {
> +		compatible = "pps-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pps>;
> +		gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
> +		status = "okay";
> +	};
> +
> +	reg_usb_otg1_vbus: regulator-usb-otg1 {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usb1_en>;
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_otg1_vbus";
> +		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +};
> +
> +&ecspi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi2>;
> +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +
> +	accel@19 {

accelerometer

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_accel>;
> +		compatible = "st,lis2de12";
> +		reg = <0x19>;
> +		st,drdy-int-pin = <1>;
> +		interrupt-parent = <&gpio4>;
> +		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-names = "INT1";
> +	};
> +};
> +
> +&i2c3 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	status = "okay";
> +};
> +
> +&sai3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_sai3>;
> +	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> +	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> +	assigned-clock-rates = <24576000>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	status = "okay";
> +};
> +
> +&usbotg1 {
> +	dr_mode = "otg";
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	pinctrl_hog: hoggrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3		0x40000041 /* PLUG_TEST */
> +			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6	0x40000041 /* PCI_USBSEL */
> +			MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7	0x40000041 /* PCIE_WDIS# */
> +			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x40000041 /* DIO0 */
> +			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x40000041 /* DIO1 */
> +			MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3	0x40000041 /* DIO2 */
> +			MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4	0x40000041 /* DIO2 */
> +		>;
> +	};
> +
> +	pinctrl_accel: accelirq {

Same comments as before.

> +		fsl,pins = <
> +			MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5	0x159
> +		>;
> +	};
> +
> +	pinctrl_gpio_leds: gpioledgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5	0x19
> +			MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4		0x19
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
> +			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
> +		>;
> +	};
> +
> +	pinctrl_pps: ppsgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x41
> +		>;
> +	};
> +
> +	pinctrl_reg_usb1_en: regusb1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x41
> +			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
> +		>;
> +	};
> +
> +	pinctrl_spi2: spi2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
> +			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
> +			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
> +			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
> +			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x140
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x140
> +			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
> new file mode 100644
> index 00000000..b1e7540
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
> @@ -0,0 +1,20 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm.dtsi"
> +#include "imx8mm-venice-gw700x.dtsi"
> +#include "imx8mm-venice-gw72xx.dtsi"

The same - empty DTS just to include DTSI. Don't multiply files. This is
development kit, carrier board, so entire contents of
imx8mm-venice-gw72xx.dtsi is *here*.

> +
> +/ {
> +	model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit";
> +	compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
> new file mode 100644
> index 00000000..3fb0213
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/ {
> +	aliases {
> +		usb0 = &usbotg1;
> +		usb1 = &usbotg2;
> +	};
> +
> +	leds {

It seems my comments apply to all your files, so I will finish the
review here.

Best regards,
Krzysztof


> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		user1 { /* GRN */
> +			label = "user1";
> +			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		user2 { /* RED */
> +			label = "user2";
> +			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};

Powered by blists - more mailing lists