| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <f74496fe-b393-4960-d58a-74e7831424d1@loongson.cn>
Date: Mon, 28 Dec 2020 09:28:26 +0800
From: zhangqing <zhangqing@...ngson.cn>
To: Huacai Chen <chenhc@...ote.com>
Cc: Mark Brown <broonie@...nel.org>, Rob Herring <robh+dt@...nel.org>,
ThomasBogendoerfer <tsbogend@...ha.franken.de>,
linux-spi@...r.kernel.org, Jiaxun Yang <jiaxun.yang@...goat.com>,
devicetree@...r.kernel.org,
"open list:MIPS" <linux-mips@...r.kernel.org>,
LKML <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v5 1/4] spi: LS7A: Add Loongson LS7A SPI controller driver
support
Hi, Huacai
On 12/28/2020 08:32 AM, Huacai Chen wrote:
> Hi, Qing,
>
> On Sat, Dec 26, 2020 at 5:13 PM Qing Zhang <zhangqing@...ngson.cn> wrote:
>> The SPI controller has the following characteristics:
>>
>> - Full-duplex synchronous serial data transmission
>> - Support up to 4 variable length byte transmission
>> - Main mode support
>> - Mode failure generates an error flag and issues an interrupt request
>> - Double buffer receiver
>> - Serial clock with programmable polarity and phase
>> - SPI can be controlled in wait mode
>> - Support boot from SPI
>>
>> Use mtd_debug tool to earse/write/read /dev/mtd0 on development.
>>
>> eg:
>>
>> [root@...ux mtd-utils-1.0.0]# mtd_debug erase /dev/mtd0 0x20000 0x40000
>> Erased 262144 bytes from address 0x00020000 in flash
>> [root@...ux mtd-utils-1.0.0]# mtd_debug write /dev/mtd0 0x20000 13 1.img
>> Copied 13 bytes from 1.img to address 0x00020000 in flash
>> [root@...ux mtd-utils-1.0.0]# mtd_debug read /dev/mtd0 0x20000 13 2.img
>> Copied 13 bytes from address 0x00020000 in flash to 2.img
>> [root@...ux mtd-utils-1.0.0]# cmp -l 1.img 2.img
>>
>> Signed-off-by: Qing Zhang <zhangqing@...ngson.cn>
>> ---
>>
>> v2:
>> - keep Kconfig and Makefile sorted
>> - make the entire comment a C++ one so things look more intentional
>> - Fix unclear indentation
>> - make conditional statements to improve legibility
>> - Don't use static inline
>> - the core handle message queue
>> - Add a new binding document
>> - Fix probe part mixed pdev and PCI
>>
>> v3:
>> - expose set_cs to the core and let it handle things
>> - replace transfer_one_message to transfer_one
>> - replace spi_alloc_master to devm_spi_alloc_master
>> - split out into prepare/unprepare_message
>> - releases pci regions before unregister master
>>
>> v4:
>> - names used in the manual
>> - rename ls7a_spi_do_transfer to ls7a_spi_setup_transfer
>> - change read the spcr and sper outside of this function
>> - mode configuration moved to prepare instead
>> - remove redundancy code about unprepare/prepare_message
>> - used 0x4 instead of 0x1,WFEMPTY instead of RFEMPTY
>>
>> v5:
>> - remove unnecessary blank lines
>>
>> ---
>> drivers/spi/Kconfig | 7 ++
>> drivers/spi/Makefile | 1 +
>> drivers/spi/spi-ls7a.c | 280 +++++++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 288 insertions(+)
>> create mode 100644 drivers/spi/spi-ls7a.c
>>
>> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
>> index aadaea0..af7c0d4 100644
>> --- a/drivers/spi/Kconfig
>> +++ b/drivers/spi/Kconfig
>> @@ -413,6 +413,13 @@ config SPI_LP8841_RTC
>> Say N here unless you plan to run the kernel on an ICP DAS
>> LP-8x4x industrial computer.
>>
>> +config SPI_LS7A
>> + tristate "Loongson LS7A SPI Controller Support"
>> + depends on CPU_LOONGSON64 || COMPILE_TEST
>> + help
>> + This drivers supports the Loongson LS7A SPI controller in master
>> + SPI mode.
>> +
>> config SPI_MPC52xx
>> tristate "Freescale MPC52xx SPI (non-PSC) controller support"
>> depends on PPC_MPC52xx
>> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
>> index 6fea582..d015cf2 100644
>> --- a/drivers/spi/Makefile
>> +++ b/drivers/spi/Makefile
>> @@ -61,6 +61,7 @@ obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
>> obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
>> obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
>> obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
>> +obj-$(CONFIG_SPI_LS7A) += spi-ls7a.o
>> obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
>> obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
>> obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o
>> diff --git a/drivers/spi/spi-ls7a.c b/drivers/spi/spi-ls7a.c
>> new file mode 100644
>> index 0000000..d24b6d91
>> --- /dev/null
>> +++ b/drivers/spi/spi-ls7a.c
>> @@ -0,0 +1,280 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +//
>> +// Loongson LS7A SPI Controller driver
>> +//
>> +// Copyright (C) 2020 Loongson Technology Corporation Limited.
>> +//
>> +
>> +#include <linux/module.h>
>> +#include <linux/pci.h>
>> +#include <linux/spi/spi.h>
>> +
>> +/* define spi register */
>> +#define SPCR 0x00
>> +#define SPSR 0x01
>> +#define FIFO 0x02
>> +#define SPER 0x03
>> +#define SFC_PARAM 0x04
>> +#define SFC_SOFTCS 0x05
>> +#define SFC_TIMING 0x06
>> +
>> +struct ls7a_spi {
>> + struct spi_master *master;
>> + void __iomem *base;
>> + unsigned int hz;
>> + unsigned int mode;
>> +};
>> +
>> +static void ls7a_spi_write_reg(struct ls7a_spi *spi,
>> + unsigned char reg,
>> + unsigned char data)
>> +{
>> + writeb(data, spi->base + reg);
>> +}
>> +
>> +static char ls7a_spi_read_reg(struct ls7a_spi *spi, unsigned char reg)
>> +{
>> + return readb(spi->base + reg);
>> +}
>> +
>> +static int ls7a_spi_prepare_message(struct spi_master *master,
>> + struct spi_message *msg)
>> +{
>> + struct ls7a_spi *ls7a_spi;
>> + struct spi_device *spi = msg->spi;
>> + unsigned char val;
>> +
>> + ls7a_spi = spi_master_get_devdata(master);
>> +
>> + if (ls7a_spi->mode != spi->mode) {
>> + val = ls7a_spi_read_reg(ls7a_spi, SPCR);
>> + val &= ~0xc;
>> + if (spi->mode & SPI_CPOL)
>> + val |= 8;
>> + if (spi->mode & SPI_CPHA)
>> + val |= 4;
>> + ls7a_spi_write_reg(ls7a_spi, SPCR, val);
>> + val = ls7a_spi_read_reg(ls7a_spi, SPER);
>> + ls7a_spi_write_reg(ls7a_spi, SPER, val);
>> + ls7a_spi->mode = spi->mode;
>> + }
>> + return 0;
> I'm sorry that I hadn't review very carefully in V4 and you need to
> send another new version. In kernel code we usually keep a blank line
> before the last "return xxx" in a function, and there are several
> other places with the same problem.
>
> Huacai
Thank you again for your reply and suggestions,
I will send v6 in the soon.
Thanks,
-Qing
>
>> +}
>> +
>> +static void ls7a_spi_set_cs(struct spi_device *spi, bool enable)
>> +{
>> + struct ls7a_spi *ls7a_spi;
>> + int cs;
>> +
>> + ls7a_spi = spi_master_get_devdata(spi->master);
>> +
>> + cs = ls7a_spi_read_reg(ls7a_spi, SFC_SOFTCS) & ~(0x11 << spi->chip_select);
>> +
>> + if (!!(spi->mode & SPI_CS_HIGH) == enable)
>> + ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x1 << spi->chip_select) | cs);
>> + else
>> + ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x11 << spi->chip_select) | cs);
>> +}
>> +
>> +static int ls7a_spi_setup_transfer(struct spi_device *spi,
>> + struct spi_transfer *t)
>> +{
>> + unsigned int hz;
>> + unsigned int div, div_tmp;
>> + unsigned int bit;
>> + unsigned long clk;
>> + unsigned char val;
>> + unsigned char spcr, sper;
>> + const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
>> + struct ls7a_spi *ls7a_spi;
>> +
>> + ls7a_spi = spi_master_get_devdata(spi->master);
>> +
>> + if (t) {
>> + hz = t->speed_hz;
>> + if (!hz)
>> + hz = spi->max_speed_hz;
>> + } else {
>> + hz = spi->max_speed_hz;
>> + }
>> +
>> + if (hz & (ls7a_spi->hz != hz)) {
>> + clk = 100000000;
>> +
>> + div = DIV_ROUND_UP(clk, hz);
>> + if (div < 2)
>> + div = 2;
>> + if (div > 4096)
>> + div = 4096;
>> +
>> + bit = fls(div) - 1;
>> + if ((1 << bit) == div)
>> + bit--;
>> + div_tmp = rdiv[bit];
>> +
>> + dev_dbg(&spi->dev, "clk = %ld hz = %d div_tmp = %d bit = %d\n",
>> + clk, hz, div_tmp, bit);
>> +
>> + ls7a_spi->hz = hz;
>> + spcr = div_tmp & 3;
>> + sper = (div_tmp >> 2) & 3;
>> +
>> + val = ls7a_spi_read_reg(ls7a_spi, SPCR);
>> + ls7a_spi_write_reg(ls7a_spi, SPCR, (val & ~3) | spcr);
>> + val = ls7a_spi_read_reg(ls7a_spi, SPER);
>> + ls7a_spi_write_reg(ls7a_spi, SPER, (val & ~3) | sper);
>> + }
>> + return 0;
>> +}
>> +
>> +static int ls7a_spi_setup(struct spi_device *spi)
>> +{
>> + return ls7a_spi_setup_transfer(spi, NULL);
>> +}
>> +
>> +static int ls7a_spi_write_read_8bit(struct spi_device *spi,
>> + const u8 **tx_buf, u8 **rx_buf,
>> + unsigned int num)
>> +{
>> + struct ls7a_spi *ls7a_spi;
>> +
>> + ls7a_spi = spi_master_get_devdata(spi->master);
>> +
>> + if (tx_buf && *tx_buf) {
>> + ls7a_spi_write_reg(ls7a_spi, FIFO, *((*tx_buf)++));
>> +
>> + while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x4) == 1)
>> + ;
>> + } else {
>> + ls7a_spi_write_reg(ls7a_spi, FIFO, 0);
>> +
>> + while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x1) == 1)
>> + ;
>> + }
>> +
>> + if (rx_buf && *rx_buf)
>> + *(*rx_buf)++ = ls7a_spi_read_reg(ls7a_spi, FIFO);
>> + else
>> + ls7a_spi_read_reg(ls7a_spi, FIFO);
>> +
>> + return 1;
>> +}
>> +
>> +static unsigned int ls7a_spi_write_read(struct spi_device *spi,
>> + struct spi_transfer *xfer)
>> +{
>> + unsigned int count;
>> + const u8 *tx = xfer->tx_buf;
>> + u8 *rx = xfer->rx_buf;
>> +
>> + count = xfer->len;
>> +
>> + do {
>> + if (ls7a_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
>> + goto out;
>> + count--;
>> + } while (count);
>> +
>> +out:
>> + return xfer->len - count;
>> +}
>> +
>> +static int ls7a_spi_transfer_one(struct spi_master *master,
>> + struct spi_device *spi,
>> + struct spi_transfer *t)
>> +{
>> + int status = 0;
>> +
>> + status = ls7a_spi_setup_transfer(spi, t);
>> + if (status < 0)
>> + return status;
>> +
>> + if (t->len)
>> + ls7a_spi_write_read(spi, t);
>> +
>> + return status;
>> +}
>> +
>> +static int ls7a_spi_pci_probe(struct pci_dev *pdev,
>> + const struct pci_device_id *ent)
>> +{
>> + struct spi_master *master;
>> + struct ls7a_spi *spi;
>> + int ret;
>> +
>> + master = devm_spi_alloc_master(&pdev->dev, sizeof(*spi));
>> + if (!master)
>> + return -ENOMEM;
>> +
>> + spi = spi_master_get_devdata(master);
>> + ret = pcim_enable_device(pdev);
>> + if (ret)
>> + goto err_free_master;
>> +
>> + ret = pci_request_regions(pdev, "ls7a-spi");
>> + if (ret)
>> + goto err_free_master;
>> +
>> + spi->base = pcim_iomap(pdev, 0, pci_resource_len(pdev, 0));
>> + if (!spi->base) {
>> + ret = -EINVAL;
>> + goto err_free_master;
>> + }
>> + ls7a_spi_write_reg(spi, SPCR, 0x51);
>> + ls7a_spi_write_reg(spi, SPER, 0x00);
>> + ls7a_spi_write_reg(spi, SFC_TIMING, 0x01);
>> + ls7a_spi_write_reg(spi, SFC_PARAM, 0x40);
>> + spi->mode = 0;
>> +
>> + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
>> + master->set_cs = ls7a_spi_set_cs;
>> + master->prepare_message = ls7a_spi_prepare_message;
>> + master->setup = ls7a_spi_setup;
>> + master->transfer_one = ls7a_spi_transfer_one;
>> + master->bits_per_word_mask = SPI_BPW_MASK(8);
>> + master->num_chipselect = 4;
>> + master->dev.of_node = pdev->dev.of_node;
>> +
>> + spi->master = master;
>> +
>> + pci_set_drvdata(pdev, master);
>> +
>> + ret = spi_register_master(master);
>> + if (ret)
>> + goto err_free_master;
>> +
>> + return 0;
>> +
>> +err_free_master:
>> + pci_release_regions(pdev);
>> + return ret;
>> +}
>> +
>> +static void ls7a_spi_pci_remove(struct pci_dev *pdev)
>> +{
>> + struct spi_master *master = pci_get_drvdata(pdev);
>> +
>> + spi_unregister_master(master);
>> + pci_release_regions(pdev);
>> +}
>> +
>> +static const struct pci_device_id ls7a_spi_pci_id_table[] = {
>> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
>> + { 0, }
>> +};
>> +
>> +MODULE_DEVICE_TABLE(pci, ls7a_spi_pci_id_table);
>> +
>> +static struct pci_driver ls7a_spi_pci_driver = {
>> + .name = "ls7a-spi",
>> + .id_table = ls7a_spi_pci_id_table,
>> + .probe = ls7a_spi_pci_probe,
>> + .remove = ls7a_spi_pci_remove,
>> +};
>> +
>> +module_pci_driver(ls7a_spi_pci_driver);
>> +
>> +MODULE_AUTHOR("Juxin Gao <gaojuxin@...ngson.cn>");
>> +MODULE_AUTHOR("Qing Zhang <zhangqing@...ngson.cn>");
>> +MODULE_DESCRIPTION("Loongson LS7A SPI controller driver");
>> +MODULE_LICENSE("GPL v2");
>> --
>> 2.1.0
>>
Powered by blists - more mailing lists