| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5dda3c71-5faf-683b-c25a-37aa1849fb62@xs4all.nl>
Date: Tue, 12 Jan 2021 16:24:22 +0100
From: Hans Verkuil <hverkuil-cisco@...all.nl>
To: Maxime Ripard <maxime@...no.tech>, Eric Anholt <eric@...olt.net>,
Maarten Lankhorst <maarten.lankhorst@...ux.intel.com>,
Thomas Zimmermann <tzimmermann@...e.de>,
Daniel Vetter <daniel.vetter@...el.com>,
David Airlie <airlied@...ux.ie>
Cc: linux-rpi-kernel@...ts.infradead.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
dri-devel@...ts.freedesktop.org,
bcm-kernel-feedback-list@...adcom.com,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Dave Stevenson <dave.stevenson@...pberrypi.com>,
linux-media@...r.kernel.org
Subject: Re: [PATCH v2 00/15] drm/vc4: hdmi: Add CEC support for the BCM2711
Hi Maxime,
On 11/01/2021 15:22, Maxime Ripard wrote:
> Hi,
>
> Here's a series introducing the CEC support for the BCM2711 found on the
> RaspberryPi4.
>
> The BCM2711 HDMI controller uses a similar layout for the CEC registers, the
> main difference being that the interrupt handling part is now shared between
> both HDMI controllers.
>
> This series is mainly about fixing a couple of bugs, reworking the driver to
> support having two different interrupts, one for each direction, provided by an
> external irqchip, and enables the irqchip driver for the controller we have.
>
> This has been tested on an RPi3 and RPi4, but requires the latest firmware.
> It's is based on the 10 and 12 bpc series.
Thank you for this series, I plan to test this later this week.
Regards,
Hans
>
> Here is the cec-compliance output:
>
> pi@...pberrypi:~$ cec-ctl --tuner -p 1.0.0.0
> The CEC adapter doesn't allow setting the physical address manually, ignore this option.
>
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : 1.0.0.0
> Logical Address Mask : 0x0008
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Tuner
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : 3 (Tuner 1)
> Primary Device Type : Tuner
> Logical Address Type : Tuner
> All Device Types : Tuner
> RC TV Profile : None
> Device Features :
> None
>
> pi@...pberrypi:~$ cec-compliance
> cec-compliance SHA : not available
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : 1.0.0.0
> Logical Address Mask : 0x0008
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Tuner
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : 3 (Tuner 1)
> Primary Device Type : Tuner
> Logical Address Type : Tuner
> All Device Types : Tuner
> RC TV Profile : None
> Device Features :
> None
>
> Compliance test for device /dev/cec0:
>
> The test results mean the following:
> OK Supported correctly by the device.
> OK (Not Supported) Not supported and not mandatory for the device.
> OK (Presumed) Presumably supported. Manually check to confirm.
> OK (Unexpected) Supported correctly but is not expected to be supported for this device.
> OK (Refused) Supported by the device, but was refused.
> FAIL Failed and was expected to be supported by this device.
>
> Find remote devices:
> Polling: OK
>
> Network topology:
> System Information for device 0 (TV) from device 3 (Tuner 1):
> CEC Version : 2.0
> Physical Address : 0.0.0.0
> Primary Device Type : TV
> Vendor ID : 0x000c03
> OSD Name : 'TV '
> Power Status : Tx, OK, Rx, OK, Feature Abort
>
> Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
>
> pi@...pberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0
> The CEC adapter doesn't allow setting the physical address manually, ignore this option.
>
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : 1.0.0.0
> Logical Address Mask : 0x0008
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Tuner
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : 3 (Tuner 1)
> Primary Device Type : Tuner
> Logical Address Type : Tuner
> All Device Types : Tuner
> RC TV Profile : None
> Device Features :
> None
>
> pi@...pberrypi:~$ cec-compliance -d1
> cec-compliance SHA : not available
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : 1.0.0.0
> Logical Address Mask : 0x0008
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Tuner
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : 3 (Tuner 1)
> Primary Device Type : Tuner
> Logical Address Type : Tuner
> All Device Types : Tuner
> RC TV Profile : None
> Device Features :
> None
>
> Compliance test for device /dev/cec1:
>
> The test results mean the following:
> OK Supported correctly by the device.
> OK (Not Supported) Not supported and not mandatory for the device.
> OK (Presumed) Presumably supported. Manually check to confirm.
> OK (Unexpected) Supported correctly but is not expected to be supported for this device.
> OK (Refused) Supported by the device, but was refused.
> FAIL Failed and was expected to be supported by this device.
>
> Find remote devices:
> Polling: OK
>
> Network topology:
> System Information for device 0 (TV) from device 3 (Tuner 1):
> CEC Version : 2.0
> Physical Address : 0.0.0.0
> Primary Device Type : TV
> Vendor ID : 0x000c03
> OSD Name : 'TV '
> Power Status : Tx, OK, Rx, OK, Feature Abort
>
> Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
>
> And for the hotplug detect test:
>
> pi@...pberrypi:~$ cec-ctl --playback
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : f.f.f.f
> Logical Address Mask : 0x0000
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Playback
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : Not Allocated
> Primary Device Type : Playback
> Logical Address Type : Playback
> All Device Types : Playback
> RC TV Profile : None
> Device Features :
> None
>
> pi@...pberrypi:~$ cec-ctl -t0 --image-view-on
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : f.f.f.f
> Logical Address Mask : 0x0000
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Playback
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : Not Allocated
> Primary Device Type : Playback
> Logical Address Type : Playback
> All Device Types : Playback
> RC TV Profile : None
> Device Features :
> None
>
> Transmit from Unregistered to TV (15 to 0):
> CEC_MSG_IMAGE_VIEW_ON (0x04)
> Sequence: 1 Tx Timestamp: 9182.611s
> pi@...pberrypi:~$ cec-ctl -d1 --playback
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : f.f.f.f
> Logical Address Mask : 0x0000
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Playback
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : Not Allocated
> Primary Device Type : Playback
> Logical Address Type : Playback
> All Device Types : Playback
> RC TV Profile : None
> Device Features :
> None
>
> pi@...pberrypi:~$ cec-ctl -d1 -t0 --image-view-on
> Driver Info:
> Driver Name : vc4_hdmi
> Adapter Name : vc4
> Capabilities : 0x0000010e
> Logical Addresses
> Transmit
> Passthrough
> Driver version : 5.10.0
> Available Logical Addresses: 1
> Physical Address : f.f.f.f
> Logical Address Mask : 0x0000
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : Playback
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : Not Allocated
> Primary Device Type : Playback
> Logical Address Type : Playback
> All Device Types : Playback
> RC TV Profile : None
> Device Features :
> None
>
> Transmit from Unregistered to TV (15 to 0):
> CEC_MSG_IMAGE_VIEW_ON (0x04)
> Sequence: 1 Tx Timestamp: 9207.191s
>
> With the pulse-eight side reporting:
>
> $ sudo cec-ctl -M
> Driver Info:
> Driver Name : pulse8-cec
> Adapter Name : serio0
> Capabilities : 0x0000003f
> Physical Address
> Logical Addresses
> Transmit
> Passthrough
> Remote Control Support
> Monitor All
> Driver version : 5.9.16
> Available Logical Addresses: 1
> Connector Info : None
> Physical Address : 0.0.0.0
> Logical Address Mask : 0x0001
> CEC Version : 2.0
> Vendor ID : 0x000c03 (HDMI)
> OSD Name : 'TV '
> Logical Addresses : 1 (Allow RC Passthrough)
>
> Logical Address : 0 (TV)
> Primary Device Type : TV
> Logical Address Type : TV
> All Device Types : TV
> RC TV Profile : None
> Device Features :
> None
>
> Initial Event: State Change: PA: 0.0.0.0, LA mask: 0x0001, Conn Info: no
>
> Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)
> Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)
>
> Let me know what you think,
> Maxime
>
> Changes from v1:
> - Removed the irqchip patch in favor of a select in mach-bcm
> - Fixed HDMI1 interrupt numbers
> - Removed redundant call to drm_connector_update_edid_property
> - Fixed the condition in vc4_hdmi_connector_detect
> - Added the tags
> - Rebased on top of drm-misc-next-2021-01-06
>
> Dom Cobley (5):
> drm/vc4: hdmi: Move hdmi reset to bind
> drm/vc4: hdmi: Fix register offset with longer CEC messages
> drm/vc4: hdmi: Fix up CEC registers
> drm/vc4: hdmi: Restore cec physical address on reconnect
> drm/vc4: hdmi: Remove cec_available flag
>
> Maxime Ripard (10):
> ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
> drm/vc4: hdmi: Compute the CEC clock divider from the clock rate
> drm/vc4: hdmi: Update the CEC clock divider on HSM rate change
> drm/vc4: hdmi: Introduce a CEC clock
> drm/vc4: hdmi: Split the interrupt handlers
> drm/vc4: hdmi: Support BCM2711 CEC interrupt setup
> drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
> dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
> ARM: dts: bcm2711: Add the BSC interrupt controller
> ARM: dts: bcm2711: Add the CEC interrupt controller
>
> .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +-
> arch/arm/boot/dts/bcm2711.dtsi | 30 +++
> arch/arm/mach-bcm/Kconfig | 1 +
> arch/arm64/Kconfig.platforms | 1 +
> drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++----
> drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +-
> drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +-
> 7 files changed, 234 insertions(+), 56 deletions(-)
>
Powered by blists - more mailing lists