linux-kernel - [PATCH v5 11/16] ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20210115200141.1397785-12-paul.kocialkowski@bootlin.com>
Date:   Fri, 15 Jan 2021 21:01:36 +0100
From:   Paul Kocialkowski <paul.kocialkowski@...tlin.com>
To:     linux-media@...r.kernel.org, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        linux-doc@...r.kernel.org, devel@...verdev.osuosl.org,
        linux-sunxi@...glegroups.com
Cc:     Yong Deng <yong.deng@...ewell.com>,
        Mauro Carvalho Chehab <mchehab@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Maxime Ripard <mripard@...nel.org>,
        Chen-Yu Tsai <wens@...e.org>,
        Jernej Skrabec <jernej.skrabec@...l.net>,
        Paul Kocialkowski <paul.kocialkowski@...tlin.com>,
        Jonathan Corbet <corbet@....net>,
        Kishon Vijay Abraham I <kishon@...com>,
        Vinod Koul <vkoul@...nel.org>,
        Helen Koike <helen.koike@...labora.com>,
        Dafna Hirschfeld <dafna.hirschfeld@...labora.com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Philipp Zabel <p.zabel@...gutronix.de>,
        Sakari Ailus <sakari.ailus@...ux.intel.com>,
        Hans Verkuil <hans.verkuil@...co.com>,
        Thomas Petazzoni <thomas.petazzoni@...tlin.com>,
        kevin.lhopital@...mail.com,
        Ezequiel Garcia <ezequiel@...guardiasur.com.ar>
Subject: [PATCH v5 11/16] ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support

MIPI CSI-2 is supported on the V3s with an A31-based MIPI CSI-2 bridge
controller. The controller uses a separate D-PHY, which is the same
that is otherwise used for MIPI DSI, but used in Rx mode.

On the V3s, the CSI0 controller is dedicated to MIPI CSI-2 as it does
not have access to any parallel interface pins.

Add all the necessary nodes (CSI0, MIPI CSI-2 bridge and D-PHY) to
support the MIPI CSI-2 interface.

Note that a fwnode graph link is created between CSI0 and MIPI CSI-2
even when no sensor is connected. This will result in a probe failure
for the controller as long as no sensor is connected but this is fine
since no other interface is available.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@...tlin.com>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 68 ++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index f8f19d8fa795..7eae0295ba73 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -530,6 +530,31 @@ spi0: spi@...8000 {
 			#size-cells = <0>;
 		};
 
+		csi0: camera@...0000 {
+			compatible = "allwinner,sun8i-v3s-csi";
+			reg = <0x01cb0000 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+
+					csi0_in_mipi_csi2: endpoint {
+						remote-endpoint = <&mipi_csi2_out_csi0>;
+					};
+				};
+			};
+		};
+
 		csi1: camera@...4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
@@ -552,5 +577,48 @@ gic: interrupt-controller@...1000 {
 			#interrupt-cells = <3>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		mipi_csi2: csi@...1000 {
+			compatible = "allwinner,sun8i-v3s-mipi-csi2",
+				     "allwinner,sun6i-a31-mipi-csi2";
+			reg = <0x01cb1000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			phys = <&dphy>;
+			phy-names = "dphy";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi_csi2_in: port@0 {
+					reg = <0>;
+				};
+
+				mipi_csi2_out: port@1 {
+					reg = <1>;
+
+					mipi_csi2_out_csi0: endpoint {
+						remote-endpoint = <&csi0_in_mipi_csi2>;
+					};
+				};
+			};
+		};
+
+		dphy: d-phy@...2000 {
+			compatible = "allwinner,sun6i-a31-mipi-dphy";
+			reg = <0x01cb2000 0x1000>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_MIPI_CSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+			#phy-cells = <0>;
+		};
 	};
 };
-- 
2.30.0