| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1611034054-63867-4-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com>
Date: Tue, 19 Jan 2021 10:57:34 +0530
From: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@...inx.com>
To: Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Michal Simek <michal.simek@...inx.com>,
"Greg Kroah-Hartman" <gregkh@...uxfoundation.org>
CC: <linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-gpio@...r.kernel.org>, <git@...inx.com>,
<saikrishna12468@...il.com>,
Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@...inx.com>
Subject: [PATCH v2 3/3] pinctrl: Added Xilinx ZynqMP pinctrl driver support
Added pinctrl driver for Xilinx ZynqMP platform.
This driver queries pin information from firmware and registers
pin control accordingly.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@...inx.com>
---
drivers/pinctrl/Kconfig | 13 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-zynqmp.c | 1031 ++++++++++++++++++++++++++++++
3 files changed, 1045 insertions(+)
create mode 100644 drivers/pinctrl/pinctrl-zynqmp.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 815095326e2d..25d3c7208975 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -341,6 +341,19 @@ config PINCTRL_ZYNQ
help
This selects the pinctrl driver for Xilinx Zynq.
+config PINCTRL_ZYNQMP
+ bool "Pinctrl driver for Xilinx ZynqMP"
+ depends on ARCH_ZYNQMP
+ select PINMUX
+ select GENERIC_PINCONF
+ help
+ This selects the pinctrl driver for Xilinx ZynqMP platform.
+ This driver will query the pin information from the firmware
+ and allow configuring the pins.
+ Configuration can include the mux function to select on those
+ pin(s)/group(s), and various pin configuration parameters
+ such as pull-up, slew rate, etc.
+
config PINCTRL_INGENIC
bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
default MACH_INGENIC
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index f53933b2ff02..7e058739f0d5 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o
obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
+obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
obj-$(CONFIG_PINCTRL_INGENIC) += pinctrl-ingenic.o
obj-$(CONFIG_PINCTRL_RK805) += pinctrl-rk805.o
obj-$(CONFIG_PINCTRL_OCELOT) += pinctrl-ocelot.o
diff --git a/drivers/pinctrl/pinctrl-zynqmp.c b/drivers/pinctrl/pinctrl-zynqmp.c
new file mode 100644
index 000000000000..ec0a5d0e22d5
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-zynqmp.c
@@ -0,0 +1,1031 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP pin controller
+ *
+ * Copyright (C) 2020 Xilinx, Inc.
+ *
+ * Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@...inx.com>
+ * Rajan Vaja <rajanv@...inx.com>
+ */
+
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <linux/platform_device.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include "core.h"
+#include "pinctrl-utils.h"
+
+#define ZYNQMP_PIN_PREFIX "MIO"
+#define PINCTRL_GET_FUNC_NAME_RESP_LEN 16
+#define MAX_FUNC_NAME_LEN 16
+#define MAX_GROUP_PIN 50
+#define END_OF_FUNCTIONS "END_OF_FUNCTIONS"
+#define NUM_GROUPS_PER_RESP 6
+
+#define PINCTRL_GET_FUNC_GROUPS_RESP_LEN 12
+#define PINCTRL_GET_PIN_GROUPS_RESP_LEN 12
+#define NA_GROUP -1
+#define RESERVED_GROUP -2
+
+#define DRIVE_STRENGTH_2MA 2
+#define DRIVE_STRENGTH_4MA 4
+#define DRIVE_STRENGTH_8MA 8
+#define DRIVE_STRENGTH_12MA 12
+
+/**
+ * struct zynqmp_pmux_function - a pinmux function
+ * @name: Name of the pinmux function
+ * @groups: List of pingroups for this function
+ * @ngroups: Number of entries in @groups
+ * @node:` Firmware node matching with for function
+ *
+ * This structure holds information about pin control function
+ * and function group names supporting that function.
+ */
+struct zynqmp_pmux_function {
+ char name[MAX_FUNC_NAME_LEN];
+ const char * const *groups;
+ unsigned int ngroups;
+};
+
+/**
+ * struct zynqmp_pinctrl - driver data
+ * @pctrl: Pinctrl device
+ * @groups: Pingroups
+ * @ngroups: Number of @groups
+ * @funcs: Pinmux functions
+ * @nfuncs: Number of @funcs
+ *
+ * This struct is stored as driver data and used to retrieve
+ * information regarding pin control functions, groups and
+ * group pins.
+ */
+struct zynqmp_pinctrl {
+ struct pinctrl_dev *pctrl;
+ const struct zynqmp_pctrl_group *groups;
+ unsigned int ngroups;
+ const struct zynqmp_pmux_function *funcs;
+ unsigned int nfuncs;
+};
+
+/**
+ * struct zynqmp_pctrl_group - Pin control group info
+ * @name: Group name
+ * @pins: Group pin numbers
+ * @npins: Number of pins in group
+ */
+struct zynqmp_pctrl_group {
+ const char *name;
+ unsigned int pins[MAX_GROUP_PIN];
+ unsigned int npins;
+};
+
+/**
+ * enum zynqmp_pin_config_param - possible pin configuration parameters
+ * @PIN_CONFIG_IOSTANDARD: if the pin can select an IO standard,
+ * the argument to this parameter (on a
+ * custom format) tells the driver which
+ * alternative IO standard to use
+ */
+enum zynqmp_pin_config_param {
+ PIN_CONFIG_IOSTANDARD = PIN_CONFIG_END + 1,
+};
+
+static const struct pinconf_generic_params zynqmp_dt_params[] = {
+ {"io-standard", PIN_CONFIG_IOSTANDARD, IO_STANDARD_LVCMOS18},
+};
+
+#ifdef CONFIG_DEBUG_FS
+static const struct
+pin_config_item zynqmp_conf_items[ARRAY_SIZE(zynqmp_dt_params)] = {
+ PCONFDUMP(PIN_CONFIG_IOSTANDARD, "io-standard", NULL, true),
+};
+#endif
+
+static struct pinctrl_desc zynqmp_desc;
+
+/**
+ * zynqmp_pctrl_get_groups_count() - get group count
+ * @pctldev: Pincontrol device pointer.
+ *
+ * Get total groups count.
+ *
+ * Return: group count.
+ */
+static int zynqmp_pctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->ngroups;
+}
+
+/**
+ * zynqmp_pctrl_get_group_name() - get group name
+ * @pctldev: Pincontrol device pointer.
+ * @selector: Group ID.
+ *
+ * Get gorup's name.
+ *
+ * Return: group name.
+ */
+static const char *zynqmp_pctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->groups[selector].name;
+}
+
+/**
+ * zynqmp_pctrl_get_group_pins() - get group pins
+ * @pctldev: Pincontrol device pointer.
+ * @selector: Group ID.
+ * @pins: Pin numbers.
+ * @npins: Number of pins in group.
+ *
+ * Get gorup's pin count and pin number.
+ *
+ * Return: Success.
+ */
+static int zynqmp_pctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ const unsigned int **pins,
+ unsigned int *npins)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = pctrl->groups[selector].pins;
+ *npins = pctrl->groups[selector].npins;
+
+ return 0;
+}
+
+static const struct pinctrl_ops zynqmp_pctrl_ops = {
+ .get_groups_count = zynqmp_pctrl_get_groups_count,
+ .get_group_name = zynqmp_pctrl_get_group_name,
+ .get_group_pins = zynqmp_pctrl_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_all,
+ .dt_free_map = pinctrl_utils_free_map,
+};
+
+/**
+ * zynqmp_pinmux_request_pin() - Request a pin for muxing
+ * @pctldev: Pincontrol device pointer.
+ * @pin: Pin number.
+ *
+ * Request a pin from firmware for muxing.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinmux_request_pin(struct pinctrl_dev *pctldev,
+ unsigned int pin)
+{
+ int ret;
+
+ ret = zynqmp_pm_pinctrl_request(pin);
+ if (ret) {
+ dev_err(pctldev->dev, "request failed for pin %u\n", pin);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_pmux_get_functions_count() - get number of functions
+ * @pctldev: Pincontrol device pointer.
+ *
+ * Get total function count.
+ *
+ * Return: function count.
+ */
+static int zynqmp_pmux_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->nfuncs;
+}
+
+/**
+ * zynqmp_pmux_get_function_name() - get function name
+ * @pctldev: Pincontrol device pointer.
+ * @selector: Function ID.
+ *
+ * Get function's name.
+ *
+ * Return: function name.
+ */
+static const char *zynqmp_pmux_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->funcs[selector].name;
+}
+
+/**
+ * zynqmp_pmux_get_function_groups() - Get groups for the function
+ * @pctldev: Pincontrol device pointer.
+ * @selector: Function ID
+ * @groups: Group names.
+ * @num_groups: Number of function groups.
+ *
+ * Get function's group count and group names.
+ *
+ * Return: Success.
+ */
+static int zynqmp_pmux_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = pctrl->funcs[selector].groups;
+ *num_groups = pctrl->funcs[selector].ngroups;
+
+ return 0;
+}
+
+/**
+ * zynqmp_pinmux_set_mux() - Set requested function for the group
+ * @pctldev: Pincontrol device pointer.
+ * @function: Function ID.
+ * @group: Group ID.
+ *
+ * Loop though all pins of group and call firmware API
+ * to set requested function for all pins in group.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinmux_set_mux(struct pinctrl_dev *pctldev,
+ unsigned int function,
+ unsigned int group)
+{
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ const struct zynqmp_pctrl_group *pgrp = &pctrl->groups[group];
+ int ret, i;
+
+ for (i = 0; i < pgrp->npins; i++) {
+ unsigned int pin = pgrp->pins[i];
+
+ ret = zynqmp_pm_pinctrl_set_function(pin, function);
+ if (ret) {
+ dev_err(pctldev->dev, "set mux failed for pin %u\n",
+ pin);
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_pinmux_release_pin() - Release a pin
+ * @pctldev: Pincontrol device pointer.
+ * @pin: Pin number.
+ *
+ * Release a pin from firmware.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinmux_release_pin(struct pinctrl_dev *pctldev,
+ unsigned int pin)
+{
+ int ret;
+
+ ret = zynqmp_pm_pinctrl_release(pin);
+ if (ret) {
+ dev_err(pctldev->dev, "free pin failed for pin %u\n",
+ pin);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static const struct pinmux_ops zynqmp_pinmux_ops = {
+ .request = zynqmp_pinmux_request_pin,
+ .get_functions_count = zynqmp_pmux_get_functions_count,
+ .get_function_name = zynqmp_pmux_get_function_name,
+ .get_function_groups = zynqmp_pmux_get_function_groups,
+ .set_mux = zynqmp_pinmux_set_mux,
+ .free = zynqmp_pinmux_release_pin,
+};
+
+/**
+ * zynqmp_pinconf_cfg_get() - get config value for the pin
+ * @pctldev: Pin control device pointer.
+ * @pin: Pin number.
+ * @config: Value of config param.
+ *
+ * Get value of the requested configuration parameter for the
+ * given pin.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinconf_cfg_get(struct pinctrl_dev *pctldev,
+ unsigned int pin,
+ unsigned long *config)
+{
+ int ret;
+ unsigned int arg = 0, param = pinconf_to_config_param(*config);
+
+ if (pin >= zynqmp_desc.npins)
+ return -EOPNOTSUPP;
+
+ switch (param) {
+ case PIN_CONFIG_SLEW_RATE:
+ param = PM_PINCTRL_CONFIG_SLEW_RATE;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ param = PM_PINCTRL_CONFIG_PULL_CTRL;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ if (arg != PM_PINCTRL_BIAS_PULL_UP)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ param = PM_PINCTRL_CONFIG_PULL_CTRL;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ if (arg != PM_PINCTRL_BIAS_PULL_DOWN)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+ case PIN_CONFIG_BIAS_DISABLE:
+ param = PM_PINCTRL_CONFIG_BIAS_STATUS;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ if (arg != PM_PINCTRL_BIAS_DISABLE)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+ case PIN_CONFIG_IOSTANDARD:
+ param = PM_PINCTRL_CONFIG_VOLTAGE_STATUS;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ param = PM_PINCTRL_CONFIG_SCHMITT_CMOS;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ param = PM_PINCTRL_CONFIG_DRIVE_STRENGTH;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &arg);
+ switch (arg) {
+ case PM_PINCTRL_DRIVE_STRENGTH_2MA:
+ arg = DRIVE_STRENGTH_2MA;
+ break;
+ case PM_PINCTRL_DRIVE_STRENGTH_4MA:
+ arg = DRIVE_STRENGTH_4MA;
+ break;
+ case PM_PINCTRL_DRIVE_STRENGTH_8MA:
+ arg = DRIVE_STRENGTH_8MA;
+ break;
+ case PM_PINCTRL_DRIVE_STRENGTH_12MA:
+ arg = DRIVE_STRENGTH_12MA;
+ break;
+ default:
+ /* Invalid drive strength */
+ dev_warn(pctldev->dev,
+ "Invalid drive strength for pin %d\n",
+ pin);
+ return -EINVAL;
+ }
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ param = pinconf_to_config_param(*config);
+ *config = pinconf_to_config_packed(param, arg);
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinconf_cfg_set() - Set requested config for the pin
+ * @pctldev: Pincontrol device pointer.
+ * @pin: Pin number.
+ * @configs: Configuration to set.
+ * @num_configs: Number of configurations.
+ *
+ * Loop though all configurations and call firmware API
+ * to set requested configurations for the pin.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinconf_cfg_set(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *configs,
+ unsigned int num_configs)
+{
+ int i, ret;
+
+ if (pin >= zynqmp_desc.npins)
+ return -EOPNOTSUPP;
+
+ for (i = 0; i < num_configs; i++) {
+ unsigned int param = pinconf_to_config_param(configs[i]);
+ unsigned int arg = pinconf_to_config_argument(configs[i]);
+ unsigned int value;
+
+ switch (param) {
+ case PIN_CONFIG_SLEW_RATE:
+ param = PM_PINCTRL_CONFIG_SLEW_RATE;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, arg);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ param = PM_PINCTRL_CONFIG_PULL_CTRL;
+ arg = PM_PINCTRL_BIAS_PULL_UP;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, arg);
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ param = PM_PINCTRL_CONFIG_PULL_CTRL;
+ arg = PM_PINCTRL_BIAS_PULL_DOWN;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, arg);
+ break;
+ case PIN_CONFIG_BIAS_DISABLE:
+ param = PM_PINCTRL_CONFIG_BIAS_STATUS;
+ arg = PM_PINCTRL_BIAS_DISABLE;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, arg);
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ param = PM_PINCTRL_CONFIG_SCHMITT_CMOS;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, arg);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ switch (arg) {
+ case DRIVE_STRENGTH_2MA:
+ value = PM_PINCTRL_DRIVE_STRENGTH_2MA;
+ break;
+ case DRIVE_STRENGTH_4MA:
+ value = PM_PINCTRL_DRIVE_STRENGTH_4MA;
+ break;
+ case DRIVE_STRENGTH_8MA:
+ value = PM_PINCTRL_DRIVE_STRENGTH_8MA;
+ break;
+ case DRIVE_STRENGTH_12MA:
+ value = PM_PINCTRL_DRIVE_STRENGTH_12MA;
+ break;
+ default:
+ /* Invalid drive strength */
+ dev_warn(pctldev->dev,
+ "Invalid drive strength for pin %d\n",
+ pin);
+ return -EINVAL;
+ }
+
+ param = PM_PINCTRL_CONFIG_DRIVE_STRENGTH;
+ ret = zynqmp_pm_pinctrl_set_config(pin, param, value);
+ break;
+ case PIN_CONFIG_IOSTANDARD:
+ param = PM_PINCTRL_CONFIG_VOLTAGE_STATUS;
+ ret = zynqmp_pm_pinctrl_get_config(pin, param, &value);
+
+ if (arg != value)
+ dev_warn(pctldev->dev,
+ "Invalid IO Standard requested for pin %d\n",
+ pin);
+
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ case PIN_CONFIG_LOW_POWER_MODE:
+ /*
+ * These cases are mentioned in dts but configurable
+ * registers are unknown. So falling through to ignore
+ * boot time warnings as of now.
+ */
+ ret = 0;
+ break;
+ default:
+ dev_warn(pctldev->dev,
+ "unsupported configuration parameter '%u'\n",
+ param);
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+ if (ret)
+ dev_warn(pctldev->dev,
+ "%s failed: pin %u param %u value %u\n",
+ __func__, pin, param, arg);
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_pinconf_group_set() - Set requested config for the group
+ * @pctldev: Pincontrol device pointer.
+ * @selector: Group ID.
+ * @configs: Configuration to set.
+ * @num_configs: Number of configurations.
+ *
+ * Call function to set configs for each pin in group.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ unsigned long *configs,
+ unsigned int num_configs)
+{
+ int i, ret;
+ struct zynqmp_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ const struct zynqmp_pctrl_group *pgrp = &pctrl->groups[selector];
+
+ for (i = 0; i < pgrp->npins; i++) {
+ ret = zynqmp_pinconf_cfg_set(pctldev, pgrp->pins[i], configs,
+ num_configs);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct pinconf_ops zynqmp_pinconf_ops = {
+ .is_generic = true,
+ .pin_config_get = zynqmp_pinconf_cfg_get,
+ .pin_config_set = zynqmp_pinconf_cfg_set,
+ .pin_config_group_set = zynqmp_pinconf_group_set,
+};
+
+static struct pinctrl_desc zynqmp_desc = {
+ .name = "zynqmp_pinctrl",
+ .owner = THIS_MODULE,
+ .pctlops = &zynqmp_pctrl_ops,
+ .pmxops = &zynqmp_pinmux_ops,
+ .confops = &zynqmp_pinconf_ops,
+#ifdef CONFIG_DEBUG_FS
+ .custom_conf_items = zynqmp_conf_items,
+#endif
+};
+
+/**
+ * zynqmp_pinctrl_get_function_groups() - get groups for the function
+ * @fid: Function ID.
+ * @index: Group index.
+ * @groups: Groups data.
+ *
+ * Call firmware API to get groups for the given function.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_function_groups(u32 fid, u32 index, u16 *groups)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ qdata.qid = PM_QID_PINCTRL_GET_FUNCTION_GROUPS;
+ qdata.arg1 = fid;
+ qdata.arg2 = index;
+
+ ret = zynqmp_pm_query_data(qdata, ret_payload);
+ if (ret)
+ return ret;
+
+ memcpy(groups, &ret_payload[1], PINCTRL_GET_FUNC_GROUPS_RESP_LEN);
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_get_func_num_groups() - get number of groups in function
+ * @fid: Function ID.
+ * @ngroups: Number of groups in function.
+ *
+ * Call firmware API to get number of group in function.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_func_num_groups(u32 fid, unsigned int *ngroups)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ qdata.qid = PM_QID_PINCTRL_GET_NUM_FUNCTION_GROUPS;
+ qdata.arg1 = fid;
+
+ ret = zynqmp_pm_query_data(qdata, ret_payload);
+ if (ret)
+ return ret;
+
+ *ngroups = ret_payload[1];
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_prepare_func_groups() - prepare function and groups data
+ * @dev: Device pointer.
+ * @fid: Function ID.
+ * @func: Function data.
+ * @groups: Groups data.
+ *
+ * Query firmware to get group IDs for each function. Firmware returns
+ * group IDs. Based on gorup index for the function, group names in
+ * function are stored. For example, first gorup in "eth0" function
+ * is named as "eth0_0", second as "eth0_1" and so on.
+ *
+ * Based on group ID received from firmware, function stores name of
+ * group for that group ID. For an example, if "eth0" first group ID
+ * is x, groups[x] name will be stored as "eth0_0".
+ *
+ * Once done for each function, each function would have its group names,
+ * and each groups would also have their names.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_prepare_func_groups(struct device *dev, u32 fid,
+ struct zynqmp_pmux_function *func,
+ struct zynqmp_pctrl_group *groups)
+{
+ u16 resp[NUM_GROUPS_PER_RESP] = {0};
+ const char **fgroups;
+ int ret = 0, index, i;
+
+ fgroups = devm_kzalloc(dev, sizeof(*fgroups) * func->ngroups,
+ GFP_KERNEL);
+ if (!fgroups)
+ return -ENOMEM;
+
+ for (index = 0; index < func->ngroups; index += NUM_GROUPS_PER_RESP) {
+ ret = zynqmp_pinctrl_get_function_groups(fid, index, resp);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < NUM_GROUPS_PER_RESP; i++) {
+ if (resp[i] == (u16)NA_GROUP)
+ goto done;
+
+ if (resp[i] == (u16)RESERVED_GROUP)
+ continue;
+
+ fgroups[index + i] = devm_kasprintf(dev, GFP_KERNEL,
+ "%s_%d_grp",
+ func->name,
+ index + i);
+ groups[resp[i]].name = devm_kasprintf(dev, GFP_KERNEL,
+ "%s_%d_grp",
+ func->name,
+ index + i);
+ }
+ }
+done:
+ func->groups = fgroups;
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_get_function_name() - get function name
+ * @fid: Function ID.
+ * @name: Function name
+ *
+ * Call firmware API to get name of given function.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_function_name(u32 fid, char *name)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ qdata.qid = PM_QID_PINCTRL_GET_FUNCTION_NAME;
+ qdata.arg1 = fid;
+
+ zynqmp_pm_query_data(qdata, ret_payload);
+ memcpy(name, ret_payload, PINCTRL_GET_FUNC_NAME_RESP_LEN);
+
+ return 0;
+}
+
+/**
+ * zynqmp_pinctrl_get_num_functions() - get number of supported functions
+ * @nfuncs: Number of functions.
+ *
+ * Call firmware API to get number of functions supported by system/board.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_num_functions(unsigned int *nfuncs)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ qdata.qid = PM_QID_PINCTRL_GET_NUM_FUNCTIONS;
+
+ ret = zynqmp_pm_query_data(qdata, ret_payload);
+ if (ret)
+ return ret;
+
+ *nfuncs = ret_payload[1];
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_get_pin_groups() - get groups for the pin
+ * @pin: Pin number.
+ * @index: Group index.
+ * @groups: Groups data.
+ *
+ * Call firmware API to get groups for the given pin.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_pin_groups(u32 pin, u32 index, u16 *groups)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ qdata.qid = PM_QID_PINCTRL_GET_PIN_GROUPS;
+ qdata.arg1 = pin;
+ qdata.arg2 = index;
+
+ ret = zynqmp_pm_query_data(qdata, ret_payload);
+ if (ret)
+ return ret;
+
+ memcpy(groups, &ret_payload[1], PINCTRL_GET_PIN_GROUPS_RESP_LEN);
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_group_add_pin() - add pin to given group
+ * @group: Group data.
+ * @pin: Pin number.
+ *
+ * Add pin number to respective group's pin array at end and
+ * increment pin count for the group.
+ *
+ * Return: 0 on success else error code.
+ */
+static void zynqmp_pinctrl_group_add_pin(struct zynqmp_pctrl_group *group,
+ unsigned int pin)
+{
+ group->pins[group->npins++] = pin;
+}
+
+/**
+ * zynqmp_pinctrl_create_pin_groups() - assign pins to respective groups
+ * @dev: Device pointer.
+ * @groups: Groups data.
+ * @pin: Pin number.
+ *
+ * Query firmware to get groups available for the given pin.
+ * Based on firmware response(group IDs for the pin), add
+ * pin number to respective group's pin array.
+ *
+ * Once all pins are queries, each groups would have its number
+ * of pins and pin numbers data.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_create_pin_groups(struct device *dev,
+ struct zynqmp_pctrl_group *groups,
+ unsigned int pin)
+{
+ int ret, i, index = 0;
+ u16 resp[NUM_GROUPS_PER_RESP] = {0};
+
+ do {
+ ret = zynqmp_pinctrl_get_pin_groups(pin, index, resp);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < NUM_GROUPS_PER_RESP; i++) {
+ if (resp[i] == (u16)NA_GROUP)
+ return ret;
+
+ if (resp[i] == (u16)RESERVED_GROUP)
+ continue;
+
+ zynqmp_pinctrl_group_add_pin(&groups[resp[i]], pin);
+ }
+ index += NUM_GROUPS_PER_RESP;
+ } while (1);
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_prepare_group_pins() - prepare each group's pin data
+ * @dev: Device pointer.
+ * @groups: Groups data.
+ * @ngroups: Number of groups.
+ *
+ * Prepare pin number and number of pins data for each pins.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_prepare_group_pins(struct device *dev,
+ struct zynqmp_pctrl_group *groups,
+ unsigned int ngroups)
+{
+ unsigned int pin;
+ int ret = 0;
+
+ for (pin = 0; pin < zynqmp_desc.npins; pin++) {
+ ret = zynqmp_pinctrl_create_pin_groups(dev, groups, pin);
+ if (ret)
+ return ret;
+ }
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_prepare_function_info() - prepare function info
+ * @dev: Device pointer.
+ * @pctrl: Pin control driver data.
+ *
+ * Query firmware for functions, groups and pin information and
+ * prepare pin control driver data.
+ *
+ * Query number of functions and number of function groups (number
+ * of groups in given function) to allocate required memory buffers
+ * for functions and groups. Once buffers are allocated to store
+ * functions and groups data, query and store required information
+ * (numbe of groups and group names for each function, number of
+ * pins and pin numbers for each group).
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_prepare_function_info(struct device *dev,
+ struct zynqmp_pinctrl *pctrl)
+{
+ struct zynqmp_pmux_function *funcs;
+ struct zynqmp_pctrl_group *groups;
+ int ret, i;
+
+ ret = zynqmp_pinctrl_get_num_functions(&pctrl->nfuncs);
+ if (ret)
+ return ret;
+
+ funcs = devm_kzalloc(dev, sizeof(*funcs) * pctrl->nfuncs, GFP_KERNEL);
+ if (!funcs)
+ return -ENOMEM;
+
+ for (i = 0; i < pctrl->nfuncs; i++) {
+ zynqmp_pinctrl_get_function_name(i, funcs[i].name);
+
+ ret = zynqmp_pinctrl_get_func_num_groups(i, &funcs[i].ngroups);
+ if (ret)
+ return ret;
+
+ pctrl->ngroups += funcs[i].ngroups;
+ }
+
+ groups = devm_kzalloc(dev, sizeof(*groups) * pctrl->ngroups,
+ GFP_KERNEL);
+ if (!groups)
+ return -ENOMEM;
+
+ for (i = 0; i < pctrl->nfuncs; i++) {
+ ret = zynqmp_pinctrl_prepare_func_groups(dev, i, &funcs[i],
+ groups);
+ if (ret)
+ return ret;
+ }
+
+ ret = zynqmp_pinctrl_prepare_group_pins(dev, groups, pctrl->ngroups);
+ if (ret)
+ return ret;
+
+ pctrl->funcs = funcs;
+ pctrl->groups = groups;
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_get_num_pins() - get number of pins in system
+ * @npins: Number of pins in system/board.
+ *
+ * Call firmware API to get number of pins.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_get_num_pins(unsigned int *npins)
+{
+ struct zynqmp_pm_query_data qdata = {0};
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+ int ret;
+
+ qdata.qid = PM_QID_PINCTRL_GET_NUM_PINS;
+
+ ret = zynqmp_pm_query_data(qdata, ret_payload);
+ if (ret)
+ return ret;
+
+ *npins = ret_payload[1];
+
+ return ret;
+}
+
+/**
+ * zynqmp_pinctrl_prepare_pin_desc() - prepare pin description info
+ * @dev: Device pointer.
+ * @zynqmp_pins: Pin information.
+ * @npins: Number of pins.
+ *
+ * Query number of pins information from firmware and prepare pin
+ * description containing pin number and pin name.
+ *
+ * Return: 0 on success else error code.
+ */
+static int zynqmp_pinctrl_prepare_pin_desc(struct device *dev,
+ const struct pinctrl_pin_desc
+ **zynqmp_pins,
+ unsigned int *npins)
+{
+ struct pinctrl_pin_desc *pins, *pin;
+ int ret;
+ int i;
+
+ ret = zynqmp_pinctrl_get_num_pins(npins);
+ if (ret)
+ return ret;
+
+ pins = devm_kzalloc(dev, sizeof(*pins) * *npins, GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ for (i = 0; i < *npins; i++) {
+ pin = &pins[i];
+ pin->number = i;
+ pin->name = devm_kasprintf(dev, GFP_KERNEL, "%s%d",
+ ZYNQMP_PIN_PREFIX, i);
+ }
+
+ *zynqmp_pins = pins;
+
+ return 0;
+}
+
+static int zynqmp_pinctrl_probe(struct platform_device *pdev)
+{
+ struct zynqmp_pinctrl *pctrl;
+ int ret;
+
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ ret = zynqmp_pinctrl_prepare_pin_desc(&pdev->dev,
+ &zynqmp_desc.pins,
+ &zynqmp_desc.npins);
+ if (ret) {
+ dev_err(&pdev->dev, "%s() pin desc prepare fail with %d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ ret = zynqmp_pinctrl_prepare_function_info(&pdev->dev, pctrl);
+ if (ret) {
+ dev_err(&pdev->dev, "%s() function info prepare fail with %d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ pctrl->pctrl = pinctrl_register(&zynqmp_desc, &pdev->dev, pctrl);
+ if (IS_ERR(pctrl->pctrl)) {
+ ret = PTR_ERR(pctrl->pctrl);
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, pctrl);
+
+ dev_info(&pdev->dev, "zynqmp pinctrl initialized\n");
+
+ return ret;
+}
+
+static const struct of_device_id zynqmp_pinctrl_of_match[] = {
+ { .compatible = "xlnx,zynqmp-pinctrl" },
+ { }
+};
+
+static struct platform_driver zynqmp_pinctrl_driver = {
+ .driver = {
+ .name = "zynqmp-pinctrl",
+ .of_match_table = zynqmp_pinctrl_of_match,
+ },
+ .probe = zynqmp_pinctrl_probe,
+};
+builtin_platform_driver(zynqmp_pinctrl_driver);
--
2.17.1
Powered by blists - more mailing lists