[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20210121102922.17439-12-johan@kernel.org>
Date: Thu, 21 Jan 2021 11:29:22 +0100
From: Johan Hovold <johan@...nel.org>
To: linux-usb@...r.kernel.org
Cc: Manivannan Sadhasivam <mani@...nel.org>,
linux-kernel@...r.kernel.org, Johan Hovold <johan@...nel.org>
Subject: [PATCH 10/10] USB: serial: xr: fix B0 handling
Fix up B0 handling which should leave the baud rate unchanged and
specifically not report back a non-B0 rate when B0 is requested; must
temporarily disable hardware flow control so that RTS can be deasserted;
and should reassert DTR/RTS when moving from B0.
Fixes: a8f54b7bd132 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@...nel.org>
---
drivers/usb/serial/xr_serial.c | 23 ++++++++++++++---------
1 file changed, 14 insertions(+), 9 deletions(-)
diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
index f67e7dba9509..483d07dee19d 100644
--- a/drivers/usb/serial/xr_serial.c
+++ b/drivers/usb/serial/xr_serial.c
@@ -341,8 +341,11 @@ static int xr_set_baudrate(struct tty_struct *tty,
u16 tx_mask, rx_mask;
int ret;
- baud = clamp(tty->termios.c_ospeed, XR21V141X_MIN_SPEED,
- XR21V141X_MAX_SPEED);
+ baud = tty->termios.c_ospeed;
+ if (!baud)
+ return 0;
+
+ baud = clamp(baud, XR21V141X_MIN_SPEED, XR21V141X_MAX_SPEED);
divisor = XR_INT_OSC_HZ / baud;
idx = ((32 * XR_INT_OSC_HZ) / baud) & 0x1f;
tx_mask = xr21v141x_txrx_clk_masks[idx].tx;
@@ -399,7 +402,8 @@ static int xr_set_baudrate(struct tty_struct *tty,
}
static void xr_set_flow_mode(struct tty_struct *tty,
- struct usb_serial_port *port)
+ struct usb_serial_port *port,
+ struct ktermios *old_termios)
{
u8 flow, gpio_mode;
int ret;
@@ -411,7 +415,7 @@ static void xr_set_flow_mode(struct tty_struct *tty,
/* Set GPIO mode for controlling the pins manually by default. */
gpio_mode &= ~XR21V141X_UART_MODE_GPIO_MASK;
- if (C_CRTSCTS(tty)) {
+ if (C_CRTSCTS(tty) && C_BAUD(tty) != B0) {
dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
gpio_mode |= XR21V141X_UART_MODE_RTS_CTS;
flow = XR21V141X_UART_FLOW_MODE_HW;
@@ -438,6 +442,11 @@ static void xr_set_flow_mode(struct tty_struct *tty,
xr_uart_enable(port);
xr_set_reg_uart(port, XR21V141X_REG_GPIO_MODE, gpio_mode);
+
+ if (C_BAUD(tty) == B0)
+ xr_dtr_rts(port, 0);
+ else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+ xr_dtr_rts(port, 1);
}
static void xr_set_termios(struct tty_struct *tty,
@@ -493,11 +502,7 @@ static void xr_set_termios(struct tty_struct *tty,
if (ret)
return;
- /* If baud rate is B0, clear DTR and RTS */
- if (C_BAUD(tty) == B0)
- xr_dtr_rts(port, 0);
-
- xr_set_flow_mode(tty, port);
+ xr_set_flow_mode(tty, port, old_termios);
}
static int xr_open(struct tty_struct *tty, struct usb_serial_port *port)
--
2.26.2
Powered by blists - more mailing lists