[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20210127150815.16991-3-a-govindraju@ti.com>
Date: Wed, 27 Jan 2021 20:38:15 +0530
From: Aswath Govindraju <a-govindraju@...com>
To: unlisted-recipients:; (no To-header on input)
CC: Vignesh Raghavendra <vigneshr@...com>,
Lokesh Vutla <lokeshvutla@...com>,
Kishon Vijay Abraham I <kishon@...com>,
Faiz Abbas <faiz_abbas@...com>,
Aswath Govindraju <a-govindraju@...com>,
Nishanth Menon <nm@...com>, Tero Kristo <kristo@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Also set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@...com>
---
performance test logs using EXT4 filesystem for eMMC HS400 speed mode,
https://pastebin.ubuntu.com/p/KFphDYXj93/
performance test logs using EXT4 filesystem for SD SDR104 speed mode,
https://pastebin.ubuntu.com/p/GQKtwGT8Qg/
.../dts/ti/k3-j7200-common-proc-board.dts | 31 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 3 +-
2 files changed, 33 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 4a7182abccf5..1e1a0022822d 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,29 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_sd_dv";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -70,6 +93,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -190,6 +219,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 75dffbb26d52..8392d771ef13 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -534,6 +534,8 @@
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -551,7 +553,6 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
dma-coherent;
};
--
2.17.1
Powered by blists - more mailing lists