| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <e5af848c-6fb8-0423-5499-a8d33329209f@xs4all.nl>
Date: Wed, 27 Jan 2021 16:28:42 +0100
From: Hans Verkuil <hverkuil-cisco@...all.nl>
To: Maxime Ripard <maxime@...no.tech>, Eric Anholt <eric@...olt.net>,
Maarten Lankhorst <maarten.lankhorst@...ux.intel.com>,
Thomas Zimmermann <tzimmermann@...e.de>,
Daniel Vetter <daniel.vetter@...el.com>,
David Airlie <airlied@...ux.ie>
Cc: linux-rpi-kernel@...ts.infradead.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
dri-devel@...ts.freedesktop.org,
bcm-kernel-feedback-list@...adcom.com,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Dave Stevenson <dave.stevenson@...pberrypi.com>,
linux-media@...r.kernel.org
Subject: Re: [PATCH v2 00/15] drm/vc4: hdmi: Add CEC support for the BCM2711
On 18/01/2021 14:55, Hans Verkuil wrote:
> On 12/01/2021 16:24, Hans Verkuil wrote:
>> Hi Maxime,
>>
>> On 11/01/2021 15:22, Maxime Ripard wrote:
>>> Hi,
>>>
>>> Here's a series introducing the CEC support for the BCM2711 found on the
>>> RaspberryPi4.
>>>
>>> The BCM2711 HDMI controller uses a similar layout for the CEC registers, the
>>> main difference being that the interrupt handling part is now shared between
>>> both HDMI controllers.
>>>
>>> This series is mainly about fixing a couple of bugs, reworking the driver to
>>> support having two different interrupts, one for each direction, provided by an
>>> external irqchip, and enables the irqchip driver for the controller we have.
>>>
>>> This has been tested on an RPi3 and RPi4, but requires the latest firmware.
>>> It's is based on the 10 and 12 bpc series.
>>
>> Thank you for this series, I plan to test this later this week.
>
> Testing is delayed: my microHDMI to HDMI adapter has problems with the CEC pin
> (possibly not connected at all). I've ordered adapter cables (hopefully of better
> quality), but those haven't arrived yet. I expect them later this week.
After testing this you can add my:
Acked-by: Hans Verkuil <hverkuil-cisco@...all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@...all.nl>
for the patches in this series.
Thank you for working on this!
Regards,
Hans
>
> Regards,
>
> Hans
>
>>
>> Regards,
>>
>> Hans
>>
>>>
>>> Here is the cec-compliance output:
>>>
>>> pi@...pberrypi:~$ cec-ctl --tuner -p 1.0.0.0
>>> The CEC adapter doesn't allow setting the physical address manually, ignore this option.
>>>
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : 1.0.0.0
>>> Logical Address Mask : 0x0008
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Tuner
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : 3 (Tuner 1)
>>> Primary Device Type : Tuner
>>> Logical Address Type : Tuner
>>> All Device Types : Tuner
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> pi@...pberrypi:~$ cec-compliance
>>> cec-compliance SHA : not available
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : 1.0.0.0
>>> Logical Address Mask : 0x0008
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Tuner
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : 3 (Tuner 1)
>>> Primary Device Type : Tuner
>>> Logical Address Type : Tuner
>>> All Device Types : Tuner
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> Compliance test for device /dev/cec0:
>>>
>>> The test results mean the following:
>>> OK Supported correctly by the device.
>>> OK (Not Supported) Not supported and not mandatory for the device.
>>> OK (Presumed) Presumably supported. Manually check to confirm.
>>> OK (Unexpected) Supported correctly but is not expected to be supported for this device.
>>> OK (Refused) Supported by the device, but was refused.
>>> FAIL Failed and was expected to be supported by this device.
>>>
>>> Find remote devices:
>>> Polling: OK
>>>
>>> Network topology:
>>> System Information for device 0 (TV) from device 3 (Tuner 1):
>>> CEC Version : 2.0
>>> Physical Address : 0.0.0.0
>>> Primary Device Type : TV
>>> Vendor ID : 0x000c03
>>> OSD Name : 'TV '
>>> Power Status : Tx, OK, Rx, OK, Feature Abort
>>>
>>> Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
>>>
>>> pi@...pberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0
>>> The CEC adapter doesn't allow setting the physical address manually, ignore this option.
>>>
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : 1.0.0.0
>>> Logical Address Mask : 0x0008
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Tuner
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : 3 (Tuner 1)
>>> Primary Device Type : Tuner
>>> Logical Address Type : Tuner
>>> All Device Types : Tuner
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> pi@...pberrypi:~$ cec-compliance -d1
>>> cec-compliance SHA : not available
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : 1.0.0.0
>>> Logical Address Mask : 0x0008
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Tuner
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : 3 (Tuner 1)
>>> Primary Device Type : Tuner
>>> Logical Address Type : Tuner
>>> All Device Types : Tuner
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> Compliance test for device /dev/cec1:
>>>
>>> The test results mean the following:
>>> OK Supported correctly by the device.
>>> OK (Not Supported) Not supported and not mandatory for the device.
>>> OK (Presumed) Presumably supported. Manually check to confirm.
>>> OK (Unexpected) Supported correctly but is not expected to be supported for this device.
>>> OK (Refused) Supported by the device, but was refused.
>>> FAIL Failed and was expected to be supported by this device.
>>>
>>> Find remote devices:
>>> Polling: OK
>>>
>>> Network topology:
>>> System Information for device 0 (TV) from device 3 (Tuner 1):
>>> CEC Version : 2.0
>>> Physical Address : 0.0.0.0
>>> Primary Device Type : TV
>>> Vendor ID : 0x000c03
>>> OSD Name : 'TV '
>>> Power Status : Tx, OK, Rx, OK, Feature Abort
>>>
>>> Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
>>>
>>> And for the hotplug detect test:
>>>
>>> pi@...pberrypi:~$ cec-ctl --playback
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : f.f.f.f
>>> Logical Address Mask : 0x0000
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Playback
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : Not Allocated
>>> Primary Device Type : Playback
>>> Logical Address Type : Playback
>>> All Device Types : Playback
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> pi@...pberrypi:~$ cec-ctl -t0 --image-view-on
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : f.f.f.f
>>> Logical Address Mask : 0x0000
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Playback
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : Not Allocated
>>> Primary Device Type : Playback
>>> Logical Address Type : Playback
>>> All Device Types : Playback
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> Transmit from Unregistered to TV (15 to 0):
>>> CEC_MSG_IMAGE_VIEW_ON (0x04)
>>> Sequence: 1 Tx Timestamp: 9182.611s
>>> pi@...pberrypi:~$ cec-ctl -d1 --playback
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : f.f.f.f
>>> Logical Address Mask : 0x0000
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Playback
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : Not Allocated
>>> Primary Device Type : Playback
>>> Logical Address Type : Playback
>>> All Device Types : Playback
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> pi@...pberrypi:~$ cec-ctl -d1 -t0 --image-view-on
>>> Driver Info:
>>> Driver Name : vc4_hdmi
>>> Adapter Name : vc4
>>> Capabilities : 0x0000010e
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Driver version : 5.10.0
>>> Available Logical Addresses: 1
>>> Physical Address : f.f.f.f
>>> Logical Address Mask : 0x0000
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : Playback
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : Not Allocated
>>> Primary Device Type : Playback
>>> Logical Address Type : Playback
>>> All Device Types : Playback
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> Transmit from Unregistered to TV (15 to 0):
>>> CEC_MSG_IMAGE_VIEW_ON (0x04)
>>> Sequence: 1 Tx Timestamp: 9207.191s
>>>
>>> With the pulse-eight side reporting:
>>>
>>> $ sudo cec-ctl -M
>>> Driver Info:
>>> Driver Name : pulse8-cec
>>> Adapter Name : serio0
>>> Capabilities : 0x0000003f
>>> Physical Address
>>> Logical Addresses
>>> Transmit
>>> Passthrough
>>> Remote Control Support
>>> Monitor All
>>> Driver version : 5.9.16
>>> Available Logical Addresses: 1
>>> Connector Info : None
>>> Physical Address : 0.0.0.0
>>> Logical Address Mask : 0x0001
>>> CEC Version : 2.0
>>> Vendor ID : 0x000c03 (HDMI)
>>> OSD Name : 'TV '
>>> Logical Addresses : 1 (Allow RC Passthrough)
>>>
>>> Logical Address : 0 (TV)
>>> Primary Device Type : TV
>>> Logical Address Type : TV
>>> All Device Types : TV
>>> RC TV Profile : None
>>> Device Features :
>>> None
>>>
>>> Initial Event: State Change: PA: 0.0.0.0, LA mask: 0x0001, Conn Info: no
>>>
>>> Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)
>>> Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)
>>>
>>> Let me know what you think,
>>> Maxime
>>>
>>> Changes from v1:
>>> - Removed the irqchip patch in favor of a select in mach-bcm
>>> - Fixed HDMI1 interrupt numbers
>>> - Removed redundant call to drm_connector_update_edid_property
>>> - Fixed the condition in vc4_hdmi_connector_detect
>>> - Added the tags
>>> - Rebased on top of drm-misc-next-2021-01-06
>>>
>>> Dom Cobley (5):
>>> drm/vc4: hdmi: Move hdmi reset to bind
>>> drm/vc4: hdmi: Fix register offset with longer CEC messages
>>> drm/vc4: hdmi: Fix up CEC registers
>>> drm/vc4: hdmi: Restore cec physical address on reconnect
>>> drm/vc4: hdmi: Remove cec_available flag
>>>
>>> Maxime Ripard (10):
>>> ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
>>> drm/vc4: hdmi: Compute the CEC clock divider from the clock rate
>>> drm/vc4: hdmi: Update the CEC clock divider on HSM rate change
>>> drm/vc4: hdmi: Introduce a CEC clock
>>> drm/vc4: hdmi: Split the interrupt handlers
>>> drm/vc4: hdmi: Support BCM2711 CEC interrupt setup
>>> drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
>>> dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
>>> ARM: dts: bcm2711: Add the BSC interrupt controller
>>> ARM: dts: bcm2711: Add the CEC interrupt controller
>>>
>>> .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +-
>>> arch/arm/boot/dts/bcm2711.dtsi | 30 +++
>>> arch/arm/mach-bcm/Kconfig | 1 +
>>> arch/arm64/Kconfig.platforms | 1 +
>>> drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++----
>>> drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +-
>>> drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +-
>>> 7 files changed, 234 insertions(+), 56 deletions(-)
>>>
>>
>
Powered by blists - more mailing lists