| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAJMQK-iYYGQ3N08PnkDzwSOc22ydEeekp_e1bXrm9Eas9xJQrA@mail.gmail.com>
Date: Wed, 3 Feb 2021 14:27:08 +0800
From: Hsin-Yi Wang <hsinyi@...omium.org>
To: Michael Kao <michael.kao@...iatek.com>
Cc: fan.chen@...iatek.com, Zhang Rui <rui.zhang@...el.com>,
Daniel Lezcano <daniel.lezcano@...aro.org>,
Linux PM <linux-pm@...r.kernel.org>,
srv_heupstream@...iatek.com,
Eduardo Valentin <edubezval@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Matthias Brugger <matthias.bgg@...il.com>,
Devicetree List <devicetree@...r.kernel.org>,
lkml <linux-kernel@...r.kernel.org>,
"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
<linux-arm-kernel@...ts.infradead.org>,
"moderated list:ARM/Mediatek SoC support"
<linux-mediatek@...ts.infradead.org>
Subject: Re: [v6,1/3] arm64: dts: mt8183: add thermal zone node
On Fri, Jan 29, 2021 at 6:10 PM Michael Kao <michael.kao@...iatek.com> wrote:
>
> From: "michael.kao" <michael.kao@...iatek.com>
>
> Add thermal zone node to Mediatek MT8183 dts file.
>
> Evaluate the thermal zone every 500ms while not cooling
> and every 100ms when passive cooling is performed.
>
> Signed-off-by: Matthias Kaehlcke <mka@...omium.org>
> Signed-off-by: Michael Kao <michael.kao@...iatek.com>
> ---
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 84 ++++++++++++++++++++++++
> 1 file changed, 84 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> index 5b782a4769e7..0aa31d338fb0 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> @@ -657,6 +657,87 @@
> status = "disabled";
> };
>
> + thermal: thermal@...0b000 {
> + #thermal-sensor-cells = <1>;
> + compatible = "mediatek,mt8183-thermal";
> + reg = <0 0x1100b000 0 0x1000>;
> + clocks = <&infracfg CLK_INFRA_THERM>,
> + <&infracfg CLK_INFRA_AUXADC>;
> + clock-names = "therm", "auxadc";
> + resets = <&infracfg MT8183_INFRACFG_AO_THERM_SW_RST>;
> + interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>;
> + mediatek,auxadc = <&auxadc>;
> + mediatek,apmixedsys = <&apmixedsys>;
> + nvmem-cells = <&thermal_calibration>;
> + nvmem-cell-names = "calibration-data";
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu_thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <500>;
> + thermal-sensors = <&thermal 0>;
> + sustainable-power = <5000>;
> + };
> +
> + /* The tzts1 ~ tzts6 don't need to polling */
> + /* The tzts1 ~ tzts6 don't need to thermal throttle */
> +
> + tzts1: tzts1 {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 1>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> +
> + tzts2: tzts2 {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 2>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> +
> + tzts3: tzts3 {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 3>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> +
> + tzts4: tzts4 {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 4>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> +
> + tzts5: tzts5 {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 5>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> +
> + tztsABB: tztsABB {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&thermal 6>;
> + sustainable-power = <5000>;
> + trips {};
> + cooling-maps {};
> + };
> + };
> +
> pwm0: pwm@...0e000 {
> compatible = "mediatek,mt8183-disp-pwm";
> reg = <0 0x1100e000 0 0x1000>;
> @@ -926,6 +1007,9 @@
> reg = <0 0x11f10000 0 0x1000>;
> #address-cells = <1>;
> #size-cells = <1>;
> + thermal_calibration: calib@180 {
> + reg = <0x180 0xc>;
> +
missing };
> mipi_tx_calibration: calib@190 {
> reg = <0x190 0xc>;
> };
> --
> 2.18.0
>
Powered by blists - more mailing lists