linux-kernel - [PATCH] drivers: nvmem: Fix voltage settings for QTI qfprom-efuse

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <1612524533-3970-1-git-send-email-rbokka@codeaurora.org>
Date:   Fri,  5 Feb 2021 16:58:52 +0530
From:   Ravi Kumar Bokka <rbokka@...eaurora.org>
To:     Srinivas Kandagatla <srinivas.kandagatla@...aro.org>,
        Douglas Anderson <dianders@...omium.org>
Cc:     linux-kernel@...r.kernel.org, devicetree@...r.kernel.org,
        rnayak@...eaurora.org, saiprakash.ranjan@...eaurora.org,
        dhavalp@...eaurora.org, mturney@...eaurora.org,
        Ravi Kumar Bokka <rbokka@...eaurora.org>
Subject: [PATCH] drivers: nvmem: Fix voltage settings for QTI qfprom-efuse

QFPROM controller hardware requires 1.8V min for fuse blowing.
So, this change sets the voltage to 1.8V, required to blow the fuse
for qfprom-efuse controller.

To disable fuse blowing, we set the voltage to 0V since this may
be a shared rail and may be able to run at a lower rate when we're
not blowing fuses.

Fixes: 93b4e49f8c86 ("nvmem: qfprom: Add fuse blowing support")
Reported-by: Douglas Anderson <dianders@...omium.org>
Suggested-by: Douglas Anderson <dianders@...omium.org>
Signed-off-by: Ravi Kumar Bokka <rbokka@...eaurora.org>
---
 drivers/nvmem/qfprom.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/drivers/nvmem/qfprom.c b/drivers/nvmem/qfprom.c
index 6cace24..100d69d 100644
--- a/drivers/nvmem/qfprom.c
+++ b/drivers/nvmem/qfprom.c
@@ -127,6 +127,16 @@ static void qfprom_disable_fuse_blowing(const struct qfprom_priv *priv,
 {
 	int ret;
 
+	/*
+	 * This may be a shared rail and may be able to run at a lower rate
+	 * when we're not blowing fuses.  At the moment, the regulator framework
+	 * applies voltage constraints even on disabled rails, so remove our
+	 * constraints and allow the rail to be adjusted by other users.
+	 */
+	ret = regulator_set_voltage(priv->vcc, 0, INT_MAX);
+	if (ret)
+		dev_warn(priv->dev, "Failed to set 0 voltage (ignoring)\n");
+
 	ret = regulator_disable(priv->vcc);
 	if (ret)
 		dev_warn(priv->dev, "Failed to disable regulator (ignoring)\n");
@@ -172,6 +182,17 @@ static int qfprom_enable_fuse_blowing(const struct qfprom_priv *priv,
 		goto err_clk_prepared;
 	}
 
+	/*
+	 * Hardware requires 1.8V min for fuse blowing; this may be
+	 * a rail shared do don't specify a max--regulator constraints
+	 * will handle.
+	 */
+	ret = regulator_set_voltage(priv->vcc, 1800000, INT_MAX);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set 1.8 voltage\n");
+		goto err_clk_rate_set;
+	}
+
 	ret = regulator_enable(priv->vcc);
 	if (ret) {
 		dev_err(priv->dev, "Failed to enable regulator\n");
-- 
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by the Linux Foundation.