Message-ID: <757b557a-b5f6-6018-caa4-34bffb1b60b7@codeaurora.org>
Date:   Fri, 19 Feb 2021 16:14:34 +0530
From:   Akhil P Oommen <akhilpo@...eaurora.org>
To:     Rob Clark <robdclark@...il.com>
Cc:     Jonathan Marek <jonathan@...ek.ca>,
        freedreno <freedreno@...ts.freedesktop.org>,
        Sean Paul <sean@...rly.run>, David Airlie <airlied@...ux.ie>,
        Daniel Vetter <daniel@...ll.ch>,
        Sai Prakash Ranjan <saiprakash.ranjan@...eaurora.org>,
        Eric Anholt <eric@...olt.net>,
        "open list:DRM DRIVER FOR MSM ADRENO GPU" 
        <linux-arm-msm@...r.kernel.org>,
        "open list:DRM DRIVER FOR MSM ADRENO GPU" 
        <dri-devel@...ts.freedesktop.org>,
        open list <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH] drm/msm/a6xx: fix for kernels without CONFIG_NVMEM

On 2/18/2021 9:41 PM, Rob Clark wrote:
> On Thu, Feb 18, 2021 at 4:28 AM Akhil P Oommen <akhilpo@...eaurora.org> wrote:
>>
>> On 2/18/2021 2:05 AM, Jonathan Marek wrote:
>>> On 2/17/21 3:18 PM, Rob Clark wrote:
>>>> On Wed, Feb 17, 2021 at 11:08 AM Jordan Crouse
>>>> <jcrouse@...eaurora.org> wrote:
>>>>>
>>>>> On Wed, Feb 17, 2021 at 07:14:16PM +0530, Akhil P Oommen wrote:
>>>>>> On 2/17/2021 8:36 AM, Rob Clark wrote:
>>>>>>> On Tue, Feb 16, 2021 at 12:10 PM Jonathan Marek <jonathan@...ek.ca>
>>>>>>> wrote:
>>>>>>>>
>>>>>>>> Ignore nvmem_cell_get() EOPNOTSUPP error in the same way as a
>>>>>>>> ENOENT error,
>>>>>>>> to fix the case where the kernel was compiled without CONFIG_NVMEM.
>>>>>>>>
>>>>>>>> Fixes: fe7952c629da ("drm/msm: Add speed-bin support to a618 gpu")
>>>>>>>> Signed-off-by: Jonathan Marek <jonathan@...ek.ca>
>>>>>>>> ---
>>>>>>>>    drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 6 +++---
>>>>>>>>    1 file changed, 3 insertions(+), 3 deletions(-)
>>>>>>>>
>>>>>>>> diff --git a/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
>>>>>>>> b/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
>>>>>>>> index ba8e9d3cf0fe..7fe5d97606aa 100644
>>>>>>>> --- a/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
>>>>>>>> +++ b/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
>>>>>>>> @@ -1356,10 +1356,10 @@ static int a6xx_set_supported_hw(struct
>>>>>>>> device *dev, struct a6xx_gpu *a6xx_gpu,
>>>>>>>>
>>>>>>>>           cell = nvmem_cell_get(dev, "speed_bin");
>>>>>>>>           /*
>>>>>>>> -        * -ENOENT means that the platform doesn't support
>>>>>>>> speedbin which is
>>>>>>>> -        * fine
>>>>>>>> +        * -ENOENT means no speed bin in device tree,
>>>>>>>> +        * -EOPNOTSUPP means kernel was built without CONFIG_NVMEM
>>>>>>>
>>>>>>> very minor nit, it would be nice to at least preserve the gist of the
>>>>>>> "which is fine" (ie. some variation of "this is an optional thing and
>>>>>>> things won't catch fire without it" ;-))
>>>>>>>
>>>>>>> (which is, I believe, is true, hopefully Akhil could confirm.. if not
>>>>>>> we should have a harder dependency on CONFIG_NVMEM..)
>>>>>> IIRC, if the gpu opp table in the DT uses the 'opp-supported-hw'
>>>>>> property,
>>>>>> we will see some error during boot up if we don't call
>>>>>> dev_pm_opp_set_supported_hw(). So calling "nvmem_cell_get(dev,
>>>>>> "speed_bin")"
>>>>>> is a way to test this.
>>>>>>
>>>>>> If there is no other harm, we can put a hard dependency on
>>>>>> CONFIG_NVMEM.
>>>>>
>>>>> I'm not sure if we want to go this far given the squishiness about
>>>>> module
>>>>> dependencies. As far as I know we are the only driver that uses this
>>>>> seriously
>>>>> on QCOM SoCs and this is only needed for certain targets. I don't
>>>>> know if we
>>>>> want to force every target to build NVMEM and QFPROM on our behalf.
>>>>> But maybe
>>>>> I'm just saying that because Kconfig dependencies tend to break my
>>>>> brain (and
>>>>> then Arnd has to send a patch to fix it).
>>>>>
>>>>
>>>> Hmm, good point.. looks like CONFIG_NVMEM itself doesn't have any
>>>> other dependencies, so I suppose it wouldn't be the end of the world
>>>> to select that.. but I guess we don't want to require QFPROM
>>>>
>>>> I guess at the end of the day, what is the failure mode if you have a
>>>> speed-bin device, but your kernel config misses QFPROM (and possibly
>>>> NVMEM)?  If the result is just not having the highest clk rate(s)
>>
>> Atleast on sc7180's gpu, using an unsupported FMAX breaks gmu. It won't
>> be very obvious what went wrong when this happens!
> 
> Ugg, ok..
> 
> I suppose we could select NVMEM, but not QFPROM, and then the case
> where QFPROM is not enabled on platforms that have the speed-bin field
> in DT will fail gracefully and all other platforms would continue on
> happily?
> 
> BR,
> -R

Sounds good to me.

-Akhil.

> 
>>
>>>> available, that isn't the end of the world.  But if it makes things
>>>> not-work, that is sub-optimal.  Generally, especially on ARM, kconfig
>>>> seems to be way harder than it should be to build a kernel that works,
>>>> if we could somehow not add to that problem (for both people with a6xx
>>>> and older gens) that would be nice ;-)
>>>>
>>>
>>> There is a "imply" kconfig option which solves exactly this problem.
>>> (you would "imply NVMEM" instead of "select NVMEM". then it would be
>>> possible to disable NVMEM but it would get enabled by default)
>>>
>>>> BR,
>>>> -R
>>>>
>>> _______________________________________________
>>> dri-devel mailing list
>>> dri-devel@...ts.freedesktop.org
>>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>>

Powered by blists - more mailing lists