Message-ID: <BYAPR02MB5896566D19BADC73FEA9A65DC19E9@BYAPR02MB5896.namprd02.prod.outlook.com>
Date:   Thu, 25 Feb 2021 11:41:42 +0000
From:   Manish Narani <MNARANI@...inx.com>
To:     Michael Grzeschik <mgr@...gutronix.de>
CC:     "gregkh@...uxfoundation.org" <gregkh@...uxfoundation.org>,
        "robh+dt@...nel.org" <robh+dt@...nel.org>,
        Michal Simek <michals@...inx.com>,
        "balbi@...nel.org" <balbi@...nel.org>,
        "p.zabel@...gutronix.de" <p.zabel@...gutronix.de>,
        "devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
        "linux-usb@...r.kernel.org" <linux-usb@...r.kernel.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        git <git@...inx.com>,
        "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>
Subject: RE: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx platforms

HI Michael,

> -----Original Message-----
> From: Michael Grzeschik <mgr@...gutronix.de>
> Sent: Monday, February 22, 2021 9:01 PM
> To: Manish Narani <MNARANI@...inx.com>
> Cc: gregkh@...uxfoundation.org; robh+dt@...nel.org; Michal Simek
> <michals@...inx.com>; balbi@...nel.org; p.zabel@...gutronix.de;
> devicetree@...r.kernel.org; linux-usb@...r.kernel.org; linux-
> kernel@...r.kernel.org; git <git@...inx.com>; linux-arm-
> kernel@...ts.infradead.org
> Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
> platforms
> 
> Hi Manish!
> 
> On Tue, Dec 15, 2020 at 12:24:51PM +0530, Manish Narani wrote:
> >Add a new driver for supporting Xilinx platforms. This driver is used
> >for some sequence of operations required for Xilinx USB controllers.
> >This driver is also used to choose between PIPE clock coming from SerDes
> >and the Suspend Clock. Before the controller is out of reset, the clock
> >selection should be changed to PIPE clock in order to make the USB
> >controller work. There is a register added in Xilinx USB controller
> >register space for the same.
> >
> >Signed-off-by: Manish Narani <manish.narani@...inx.com>
> >---
> > drivers/usb/dwc3/Kconfig          |   9 +
> > drivers/usb/dwc3/Makefile         |   1 +
> > drivers/usb/dwc3/dwc3-of-simple.c |   1 -
> > drivers/usb/dwc3/dwc3-xilinx.c    | 334
> ++++++++++++++++++++++++++++++
> > 4 files changed, 344 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/usb/dwc3/dwc3-xilinx.c
> >
> >diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> >index 7a2304565a73..0e00e6dfccd8 100644
> >--- a/drivers/usb/dwc3/Kconfig
> >+++ b/drivers/usb/dwc3/Kconfig
> >@@ -139,4 +139,13 @@ config USB_DWC3_QCOM
> > 	  for peripheral mode support.
> > 	  Say 'Y' or 'M' if you have one such device.
> >
> >+config USB_DWC3_XILINX
> >+	tristate "Xilinx Platforms"
> >+	depends on (ARCH_ZYNQMP || ARCH_VERSAL) && OF
> >+	default USB_DWC3
> >+	help
> >+	  Support Xilinx SoCs with DesignWare Core USB3 IP.
> >+	  This driver handles both ZynqMP and Versal SoC operations.
> >+	  Say 'Y' or 'M' if you have one such device.
> >+
> > endif
> >diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> >index ae86da0dc5bd..add567578b1f 100644
> >--- a/drivers/usb/dwc3/Makefile
> >+++ b/drivers/usb/dwc3/Makefile
> >@@ -51,3 +51,4 @@ obj-$(CONFIG_USB_DWC3_MESON_G12A)	+=
> dwc3-meson-g12a.o
> > obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
> > obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
> > obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
> >+obj-$(CONFIG_USB_DWC3_XILINX)		+= dwc3-xilinx.o
> >diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-
> of-simple.c
> >index e62ecd22b3ed..71fd620c5161 100644
> >--- a/drivers/usb/dwc3/dwc3-of-simple.c
> >+++ b/drivers/usb/dwc3/dwc3-of-simple.c
> >@@ -172,7 +172,6 @@ static const struct dev_pm_ops
> dwc3_of_simple_dev_pm_ops = {
> >
> > static const struct of_device_id of_dwc3_simple_match[] = {
> > 	{ .compatible = "rockchip,rk3399-dwc3" },
> >-	{ .compatible = "xlnx,zynqmp-dwc3" },
> > 	{ .compatible = "cavium,octeon-7130-usb-uctl" },
> > 	{ .compatible = "sprd,sc9860-dwc3" },
> > 	{ .compatible = "allwinner,sun50i-h6-dwc3" },
> >diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-
> xilinx.c
> >new file mode 100644
> >index 000000000000..7e485951d2f7
> >--- /dev/null
> >+++ b/drivers/usb/dwc3/dwc3-xilinx.c
> >@@ -0,0 +1,334 @@
> >+// SPDX-License-Identifier: GPL-2.0
> >+/**
> >+ * dwc3-xilinx.c - Xilinx DWC3 controller specific glue driver
> >+ *
> >+ * Authors: Manish Narani <manish.narani@...inx.com>
> >+ *          Anurag Kumar Vulisha <anurag.kumar.vulisha@...inx.com>
> >+ */
> >+
> >+#include <linux/module.h>
> >+#include <linux/kernel.h>
> >+#include <linux/slab.h>
> >+#include <linux/clk.h>
> >+#include <linux/of.h>
> >+#include <linux/platform_device.h>
> >+#include <linux/dma-mapping.h>
> >+#include <linux/of_platform.h>
> >+#include <linux/pm_runtime.h>
> >+#include <linux/reset.h>
> >+#include <linux/of_address.h>
> >+#include <linux/delay.h>
> >+#include <linux/firmware/xlnx-zynqmp.h>
> >+#include <linux/io.h>
> >+
> >+#include <linux/phy/phy.h>
> >+
> >+/* USB phy reset mask register */
> >+#define XLNX_USB_PHY_RST_EN			0x001C
> >+#define XLNX_PHY_RST_MASK			0x1
> >+
> >+/* Xilinx USB 3.0 IP Register */
> >+#define XLNX_USB_TRAFFIC_ROUTE_CONFIG		0x005C
> >+#define XLNX_USB_TRAFFIC_ROUTE_FPD		0x1
> >+
> >+/* Versal USB Reset ID */
> >+#define VERSAL_USB_RESET_ID			0xC104036
> >+
> >+#define XLNX_USB_FPD_PIPE_CLK			0x7c
> >+#define PIPE_CLK_DESELECT			1
> >+#define PIPE_CLK_SELECT				0
> >+#define XLNX_USB_FPD_POWER_PRSNT		0x80
> >+#define PIPE_POWER_ON				1
> >+#define PIPE_POWER_OFF				0
> >+
> >+struct dwc3_xlnx {
> >+	int				num_clocks;
> >+	struct clk_bulk_data		*clks;
> >+	struct device			*dev;
> >+	void __iomem			*regs;
> >+	int				(*pltfm_init)(struct dwc3_xlnx *data);
> >+};
> >+
> >+static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool
> mask)
> >+{
> >+	u32 reg;
> >+
> >+	/*
> >+	 * Enable or disable ULPI PHY reset from USB Controller.
> >+	 * This does not actually reset the phy, but just controls
> >+	 * whether USB controller can or cannot reset ULPI PHY.
> >+	 */
> >+	reg = readl(priv_data->regs + XLNX_USB_PHY_RST_EN);
> >+
> >+	if (mask)
> >+		reg &= ~XLNX_PHY_RST_MASK;
> >+	else
> >+		reg |= XLNX_PHY_RST_MASK;
> >+
> >+	writel(reg, priv_data->regs + XLNX_USB_PHY_RST_EN);
> >+}
> >+
> >+static int dwc3_xlnx_init_versal(struct dwc3_xlnx *priv_data)
> >+{
> >+	struct device		*dev = priv_data->dev;
> >+	int			ret;
> >+
> >+	dwc3_xlnx_mask_phy_rst(priv_data, false);
> >+
> >+	/* Assert and De-assert reset */
> >+	ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> >+				     PM_RESET_ACTION_ASSERT);
> >+	if (ret < 0) {
> >+		dev_err_probe(dev, ret, "failed to assert Reset\n");
> >+		return ret;
> >+	}
> >+
> >+	ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> >+				     PM_RESET_ACTION_RELEASE);
> >+	if (ret < 0) {
> >+		dev_err_probe(dev, ret, "failed to De-assert Reset\n");
> >+		return ret;
> >+	}
> >+
> >+	dwc3_xlnx_mask_phy_rst(priv_data, true);
> >+
> >+	return 0;
> >+}
> >+
> >+static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> >+{
> >+	struct device		*dev = priv_data->dev;
> >+	struct reset_control	*crst, *hibrst, *apbrst;
> >+	struct phy		*usb3_phy;
> >+	int			ret;
> >+	u32			reg;
> >+
> >+	crst = devm_reset_control_get_exclusive(dev, "usb_crst");
> >+	if (IS_ERR(crst)) {
> >+		ret = PTR_ERR(crst);
> >+		dev_err_probe(dev, ret,
> >+			      "failed to get core reset signal\n");
> >+		goto err;
> >+	}
> >+
> >+	hibrst = devm_reset_control_get_exclusive(dev, "usb_hibrst");
> >+	if (IS_ERR(hibrst)) {
> >+		ret = PTR_ERR(hibrst);
> >+		dev_err_probe(dev, ret,
> >+			      "failed to get hibernation reset signal\n");
> >+		goto err;
> >+	}
> >+
> >+	apbrst = devm_reset_control_get_exclusive(dev, "usb_apbrst");
> >+	if (IS_ERR(apbrst)) {
> >+		ret = PTR_ERR(apbrst);
> >+		dev_err_probe(dev, ret,
> >+			      "failed to get APB reset signal\n");
> >+		goto err;
> >+	}
> >+
> >+	ret = reset_control_assert(crst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to assert core reset\n");
> >+		goto err;
> >+	}
> >+
> >+	ret = reset_control_assert(hibrst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to assert hibernation reset\n");
> >+		goto err;
> >+	}
> >+
> >+	ret = reset_control_assert(apbrst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to assert APB reset\n");
> >+		goto err;
> >+	}
> >+
> >+	usb3_phy = devm_phy_get(dev, "usb3-phy");
> 
> You should move this phy get to probe code and skip the call of
> pltfm_init if no phy was found.
> 
> As I understand this glue now, you will set an defined fixed-clock
> frequency from dts in the ps-gtr phy. If no phy and therefor also no
> clock is defined, the call of dwc3_xlnx_init_zynqmp can be skipped, as
> you will not need to switch the clocks to an external lane source.
> 
> For example for the host case with node option dr_mode = "host" set and
> no external physical external clksrc connected, this glue still needs to
> be used. The current version would break this case.

OK Michael. I will take care of the same in the next version of the driver.

Thanks,
Manish

> 
> Thanks,
> Michael
> 
> >+	ret = phy_init(usb3_phy);
> >+	if (ret < 0) {
> >+		phy_exit(usb3_phy);
> >+		goto err;
> >+	}
> >+
> >+	ret = reset_control_deassert(apbrst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to release APB reset\n");
> >+		goto err;
> >+	}
> >+
> >+	/* Set PIPE Power Present signal in FPD Power Present Register*/
> >+	writel(PIPE_POWER_ON, priv_data->regs +
> XLNX_USB_FPD_POWER_PRSNT);
> >+
> >+	/* Set the PIPE Clock Select bit in FPD PIPE Clock register */
> >+	writel(PIPE_CLK_SELECT, priv_data->regs +
> XLNX_USB_FPD_PIPE_CLK);
> >+
> >+	ret = reset_control_deassert(crst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to release core reset\n");
> >+		goto err;
> >+	}
> >+
> >+	ret = reset_control_deassert(hibrst);
> >+	if (ret < 0) {
> >+		dev_err(dev, "Failed to release hibernation reset\n");
> >+		goto err;
> >+	}
> >+
> >+	ret = phy_power_on(usb3_phy);
> >+	if (ret < 0) {
> >+		phy_exit(usb3_phy);
> >+		goto err;
> >+	}
> >+
> >+	/*
> >+	 * This routes the USB DMA traffic to go through FPD path instead
> >+	 * of reaching DDR directly. This traffic routing is needed to
> >+	 * make SMMU and CCI work with USB DMA.
> >+	 */
> >+	if (of_dma_is_coherent(dev->of_node) ||
> device_iommu_mapped(dev)) {
> >+		reg = readl(priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> >+		reg |= XLNX_USB_TRAFFIC_ROUTE_FPD;
> >+		writel(reg, priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> >+	}
> >+
> >+err:
> >+	return ret;
> >+}
> >+
> >+static const struct of_device_id dwc3_xlnx_of_match[] = {
> >+	{
> >+		.compatible = "xlnx,zynqmp-dwc3",
> >+		.data = &dwc3_xlnx_init_zynqmp,
> >+	},
> >+	{
> >+		.compatible = "xlnx,versal-dwc3",
> >+		.data = &dwc3_xlnx_init_versal,
> >+	},
> >+	{ /* Sentinel */ }
> >+};
> >+MODULE_DEVICE_TABLE(of, dwc3_xlnx_of_match);
> >+
> >+static int dwc3_xlnx_probe(struct platform_device *pdev)
> >+{
> >+	struct dwc3_xlnx		*priv_data;
> >+	struct device			*dev = &pdev->dev;
> >+	struct device_node		*np = dev->of_node;
> >+	const struct of_device_id	*match;
> >+	void __iomem			*regs;
> >+	int				ret;
> >+
> >+	priv_data = devm_kzalloc(dev, sizeof(*priv_data), GFP_KERNEL);
> >+	if (!priv_data)
> >+		return -ENOMEM;
> >+
> >+	regs = devm_platform_ioremap_resource(pdev, 0);
> >+	if (IS_ERR(regs)) {
> >+		ret = PTR_ERR(regs);
> >+		dev_err_probe(dev, ret, "failed to map registers\n");
> >+		return ret;
> >+	}
> >+
> >+	match = of_match_node(dwc3_xlnx_of_match, pdev->dev.of_node);
> >+
> >+	priv_data->pltfm_init = match->data;
> >+	priv_data->regs = regs;
> >+	priv_data->dev = dev;
> >+
> >+	platform_set_drvdata(pdev, priv_data);
> >+
> >+	ret = devm_clk_bulk_get_all(priv_data->dev, &priv_data->clks);
> >+	if (ret < 0)
> >+		return ret;
> >+
> >+	priv_data->num_clocks = ret;
> >+
> >+	ret = clk_bulk_prepare_enable(priv_data->num_clocks, priv_data-
> >clks);
> >+	if (ret)
> >+		return ret;
> >+
> >+	ret = priv_data->pltfm_init(priv_data);
> >+	if (ret)
> >+		goto err_clk_put;
> >+
> >+	ret = of_platform_populate(np, NULL, NULL, dev);
> >+	if (ret)
> >+		goto err_clk_put;
> >+
> >+	pm_runtime_set_active(dev);
> >+	pm_runtime_enable(dev);
> >+	pm_suspend_ignore_children(dev, false);
> >+	pm_runtime_get_sync(dev);
> >+
> >+	return 0;
> >+
> >+err_clk_put:
> >+	clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data-
> >clks);
> >+	clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> >+
> >+	return ret;
> >+}
> >+
> >+static int dwc3_xlnx_remove(struct platform_device *pdev)
> >+{
> >+	struct dwc3_xlnx	*priv_data = platform_get_drvdata(pdev);
> >+	struct device		*dev = &pdev->dev;
> >+
> >+	of_platform_depopulate(dev);
> >+
> >+	clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data-
> >clks);
> >+	clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> >+	priv_data->num_clocks = 0;
> >+
> >+	pm_runtime_disable(dev);
> >+	pm_runtime_put_noidle(dev);
> >+	pm_runtime_set_suspended(dev);
> >+
> >+	return 0;
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_suspend_common(struct device
> *dev)
> >+{
> >+	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> >+
> >+	clk_bulk_disable(priv_data->num_clocks, priv_data->clks);
> >+
> >+	return 0;
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_resume_common(struct device
> *dev)
> >+{
> >+	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> >+
> >+	return clk_bulk_enable(priv_data->num_clocks, priv_data->clks);
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_runtime_idle(struct device *dev)
> >+{
> >+	pm_runtime_mark_last_busy(dev);
> >+	pm_runtime_autosuspend(dev);
> >+
> >+	return 0;
> >+}
> >+
> >+static UNIVERSAL_DEV_PM_OPS(dwc3_xlnx_dev_pm_ops,
> dwc3_xlnx_suspend_common,
> >+			    dwc3_xlnx_resume_common,
> dwc3_xlnx_runtime_idle);
> >+
> >+static struct platform_driver dwc3_xlnx_driver = {
> >+	.probe		= dwc3_xlnx_probe,
> >+	.remove		= dwc3_xlnx_remove,
> >+	.driver		= {
> >+		.name		= "dwc3-xilinx",
> >+		.of_match_table	= dwc3_xlnx_of_match,
> >+		.pm		= &dwc3_xlnx_dev_pm_ops,
> >+	},
> >+};
> >+
> >+module_platform_driver(dwc3_xlnx_driver);
> >+
> >+MODULE_LICENSE("GPL v2");
> >+MODULE_DESCRIPTION("Xilinx DWC3 controller specific glue driver");
> >+MODULE_AUTHOR("Manish Narani <manish.narani@...inx.com>");
> >+MODULE_AUTHOR("Anurag Kumar Vulisha
> <anurag.kumar.vulisha@...inx.com>");
> >--
> >2.17.1
> >
> >
> >_______________________________________________
> >linux-arm-kernel mailing list
> >linux-arm-kernel@...ts.infradead.org
> >http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
> 
> --
> Pengutronix e.K.                           |                             |
> Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
> 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Powered by blists - more mailing lists