| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210304211038.12511-4-grygorii.strashko@ti.com>
Date: Thu, 4 Mar 2021 23:10:37 +0200
From: Grygorii Strashko <grygorii.strashko@...com>
To: Nishanth Menon <nm@...com>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
Vignesh Raghavendra <vigneshr@...com>,
Lokesh Vutla <lokeshvutla@...com>
CC: <linux-kernel@...r.kernel.org>, Rob Herring <robh+dt@...nel.org>,
Kishon Vijay Abraham I <kishon@...com>,
Tero Kristo <kristo@...nel.org>,
Grygorii Strashko <grygorii.strashko@...com>
Subject: [PATCH v2 3/4] arm64: dts: ti: k3-am642-evm: add CPSW3g DT nodes
From: Vignesh Raghavendra <vigneshr@...com>
On am642-evm the CPSW3g ext. Port1 is directly connected to TI DP83867 PHY
and Port2 is connected to TI DP83869 PHY which is shared with ICSS
subsystem. The TI DP83869 PHY MII interface is configured using pinmux for
CPSW3g, while MDIO bus is connected through GPIO controllable 2:1 TMUX154E
switch (MDIO GPIO MUX) which has to be configured to route MDIO bus from
CPSW3g to TI DP83869 PHY.
Hence add networking support for am642-evm:
- add CPSW3g MDIO and RGMII pinmux entries for both ext. ports;
- add CPSW3g nodes;
- add mdio-mux-multiplexer DT nodes to represent above topology.
Signed-off-by: Vignesh Raghavendra <vigneshr@...com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@...com>
Reviewed-by: Lokesh Vutla <lokeshvutla@...com>
---
arch/arm64/boot/dts/ti/k3-am642-evm.dts | 93 +++++++++++++++++++++++++
1 file changed, 93 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
index 1f1787750fef..962ef807e286 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -6,6 +6,8 @@
/dts-v1/;
#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am642.dtsi"
/ {
@@ -101,6 +103,31 @@
default-state = "off";
};
};
+
+ mdio_mux: mux-controller {
+ compatible = "gpio-mux";
+ #mux-control-cells = <0>;
+
+ mux-gpios = <&exp1 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ mdio-mux-1 {
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mdio_mux>;
+ mdio-parent-bus = <&cpsw3g_mdio>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@1 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw3g_phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };
+ };
};
&main_pmx0 {
@@ -133,6 +160,47 @@
AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */
>;
};
+
+ mdio1_pins_default: mdio1-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
+ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
+ >;
+ };
+
+ rgmii1_pins_default: rgmii1-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */
+ AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */
+ AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */
+ AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */
+ AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */
+ AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */
+ AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */
+ AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */
+ AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */
+ AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
+ AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */
+ AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */
+ >;
+ };
+
+ rgmii2_pins_default: rgmii2-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */
+ AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */
+ AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */
+ AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */
+ AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */
+ AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
+ AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */
+ AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */
+ AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */
+ AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */
+ AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */
+ AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
+ >;
+ };
};
&main_uart0 {
@@ -244,3 +312,28 @@
ti,driver-strength-ohm = <50>;
disable-wp;
};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio1_pins_default
+ &rgmii1_pins_default
+ &rgmii2_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy3>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
--
2.17.1
Powered by blists - more mailing lists