| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210308170522.4272-3-alcooperx@gmail.com>
Date: Mon, 8 Mar 2021 12:05:22 -0500
From: Al Cooper <alcooperx@...il.com>
To: linux-kernel@...r.kernel.org
Cc: Al Cooper <alcooperx@...il.com>,
bcm-kernel-feedback-list@...adcom.com, devicetree@...r.kernel.org,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Jiri Slaby <jirislaby@...nel.org>,
linux-serial@...r.kernel.org,
Masahiro Yamada <masahiroy@...nel.org>,
Rob Herring <robh+dt@...nel.org>
Subject: [PATCH v4 2/2] serial: 8250: Add new 8250-core based Broadcom STB driver
Add a UART driver for the new Broadcom 8250 based STB UART. The new
UART is backward compatible with the standard 8250, but has some
additional features. The new features include a high accuracy baud
rate clock system and DMA support.
The driver will use the new optional BAUD MUX clock to select the best
one of the four master clocks (81MHz, 108MHz, 64MHz and 48MHz) to feed
the baud rate selection logic for any requested baud rate. This allows
for more accurate BAUD rates when high speed baud rates are selected.
The driver will use the new UART DMA hardware if the UART DMA registers
are specified in Device Tree "reg" property.
The driver also sets the UPSTAT_AUTOCTS flag when hardware flow control
is enabled. This flag is needed for UARTs that don't assert a CTS
changed interrupt when CTS changes and AFE (Hardware Flow Control) is
enabled.
The driver also contains a workaround for a bug in the Synopsis 8250
core. The problem is that at high baud rates, the RX partial FIFO
timeout interrupt can occur but there is no RX data (DR not set in
the LSR register). In this case the driver will not read the Receive
Buffer Register, which clears the interrupt, and the system will get
continuous UART interrupts until the next RX character arrives. The
fix originally suggested by Synopsis was to read the Receive Buffer
Register and discard the character when the DR bit in the LSR was
not set, to clear the interrupt. The problem was that occasionally
a character would arrive just after the DR bit check and a valid
character would be discarded. The fix that was added will clear
receive interrupts to stop the interrupt, deassert RTS to insure
that no new data can arrive, wait for 1.5 character times for the
sender to react to RTS and then check for data and either do a dummy
read or a valid read. Debugfs error counters were also added and were
used to help create test software that would cause the error condition.
The counters can be found at:
/sys/kernel/debug/bcm7271-uart/<device-name>/stats
Signed-off-by: Al Cooper <alcooperx@...il.com>
---
MAINTAINERS | 8 +
drivers/tty/serial/8250/8250_bcm7271.c | 1207 ++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 10 +
drivers/tty/serial/8250/Makefile | 1 +
4 files changed, 1226 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_bcm7271.c
diff --git a/MAINTAINERS b/MAINTAINERS
index d92f85ca831d..834904841382 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3558,6 +3558,14 @@ S: Supported
F: Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml
F: drivers/i2c/busses/i2c-brcmstb.c
+BROADCOM BRCMSTB UART DRIVER
+M: Al Cooper <alcooperx@...il.com>
+L: linux-serial@...r.kernel.org
+L: bcm-kernel-feedback-list@...adcom.com
+S: Maintained
+F: Documentation/devicetree/bindings/serial/brcm,bcm7271-uart.yaml
+F: drivers/tty/serial/8250/8250_bcm7271.c
+
BROADCOM BRCMSTB USB EHCI DRIVER
M: Al Cooper <alcooperx@...il.com>
L: linux-usb@...r.kernel.org
diff --git a/drivers/tty/serial/8250/8250_bcm7271.c b/drivers/tty/serial/8250/8250_bcm7271.c
new file mode 100644
index 000000000000..3593a0a25abe
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_bcm7271.c
@@ -0,0 +1,1207 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) 2020, Broadcom */
+/*
+ * 8250-core based driver for Broadcom ns16550a UARTs
+ *
+ * This driver uses the standard 8250 driver core but adds additional
+ * optional features including the ability to use a baud rate clock
+ * mux for more accurate high speed baud rate selection and also
+ * an optional DMA engine.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/tty.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/dma-mapping.h>
+#include <linux/tty_flip.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+
+#include "8250.h"
+
+/* Register definitions for UART DMA block. Version 1.1 or later. */
+#define UDMA_ARB_RX 0x00
+#define UDMA_ARB_TX 0x04
+#define UDMA_ARB_REQ 0x00000001
+#define UDMA_ARB_GRANT 0x00000002
+
+#define UDMA_RX_REVISION 0x00
+#define UDMA_RX_REVISION_REQUIRED 0x00000101
+#define UDMA_RX_CTRL 0x04
+#define UDMA_RX_CTRL_BUF_CLOSE_MODE 0x00010000
+#define UDMA_RX_CTRL_MASK_WR_DONE 0x00008000
+#define UDMA_RX_CTRL_ENDIAN_OVERRIDE 0x00004000
+#define UDMA_RX_CTRL_ENDIAN 0x00002000
+#define UDMA_RX_CTRL_OE_IS_ERR 0x00001000
+#define UDMA_RX_CTRL_PE_IS_ERR 0x00000800
+#define UDMA_RX_CTRL_FE_IS_ERR 0x00000400
+#define UDMA_RX_CTRL_NUM_BUF_USED_MASK 0x000003c0
+#define UDMA_RX_CTRL_NUM_BUF_USED_SHIFT 6
+#define UDMA_RX_CTRL_BUF_CLOSE_CLK_SEL_SYS 0x00000020
+#define UDMA_RX_CTRL_BUF_CLOSE_ENA 0x00000010
+#define UDMA_RX_CTRL_TIMEOUT_CLK_SEL_SYS 0x00000008
+#define UDMA_RX_CTRL_TIMEOUT_ENA 0x00000004
+#define UDMA_RX_CTRL_ABORT 0x00000002
+#define UDMA_RX_CTRL_ENA 0x00000001
+#define UDMA_RX_STATUS 0x08
+#define UDMA_RX_STATUS_ACTIVE_BUF_MASK 0x0000000f
+#define UDMA_RX_TRANSFER_LEN 0x0c
+#define UDMA_RX_TRANSFER_TOTAL 0x10
+#define UDMA_RX_BUFFER_SIZE 0x14
+#define UDMA_RX_SRC_ADDR 0x18
+#define UDMA_RX_TIMEOUT 0x1c
+#define UDMA_RX_BUFFER_CLOSE 0x20
+#define UDMA_RX_BLOCKOUT_COUNTER 0x24
+#define UDMA_RX_BUF0_PTR_LO 0x28
+#define UDMA_RX_BUF0_PTR_HI 0x2c
+#define UDMA_RX_BUF0_STATUS 0x30
+#define UDMA_RX_BUFX_STATUS_OVERRUN_ERR 0x00000010
+#define UDMA_RX_BUFX_STATUS_FRAME_ERR 0x00000008
+#define UDMA_RX_BUFX_STATUS_PARITY_ERR 0x00000004
+#define UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED 0x00000002
+#define UDMA_RX_BUFX_STATUS_DATA_RDY 0x00000001
+#define UDMA_RX_BUF0_DATA_LEN 0x34
+#define UDMA_RX_BUF1_PTR_LO 0x38
+#define UDMA_RX_BUF1_PTR_HI 0x3c
+#define UDMA_RX_BUF1_STATUS 0x40
+#define UDMA_RX_BUF1_DATA_LEN 0x44
+
+#define UDMA_TX_REVISION 0x00
+#define UDMA_TX_REVISION_REQUIRED 0x00000101
+#define UDMA_TX_CTRL 0x04
+#define UDMA_TX_CTRL_ENDIAN_OVERRIDE 0x00000080
+#define UDMA_TX_CTRL_ENDIAN 0x00000040
+#define UDMA_TX_CTRL_NUM_BUF_USED_MASK 0x00000030
+#define UDMA_TX_CTRL_NUM_BUF_USED_1 0x00000010
+#define UDMA_TX_CTRL_ABORT 0x00000002
+#define UDMA_TX_CTRL_ENA 0x00000001
+#define UDMA_TX_DST_ADDR 0x08
+#define UDMA_TX_BLOCKOUT_COUNTER 0x10
+#define UDMA_TX_TRANSFER_LEN 0x14
+#define UDMA_TX_TRANSFER_TOTAL 0x18
+#define UDMA_TX_STATUS 0x20
+#define UDMA_TX_BUF0_PTR_LO 0x24
+#define UDMA_TX_BUF0_PTR_HI 0x28
+#define UDMA_TX_BUF0_STATUS 0x2c
+#define UDMA_TX_BUFX_LAST 0x00000002
+#define UDMA_TX_BUFX_EMPTY 0x00000001
+#define UDMA_TX_BUF0_DATA_LEN 0x30
+#define UDMA_TX_BUF0_DATA_SENT 0x34
+#define UDMA_TX_BUF1_PTR_LO 0x38
+
+#define UDMA_INTR_STATUS 0x00
+#define UDMA_INTR_ARB_TX_GRANT 0x00040000
+#define UDMA_INTR_ARB_RX_GRANT 0x00020000
+#define UDMA_INTR_TX_ALL_EMPTY 0x00010000
+#define UDMA_INTR_TX_EMPTY_BUF1 0x00008000
+#define UDMA_INTR_TX_EMPTY_BUF0 0x00004000
+#define UDMA_INTR_TX_ABORT 0x00002000
+#define UDMA_INTR_TX_DONE 0x00001000
+#define UDMA_INTR_RX_ERROR 0x00000800
+#define UDMA_INTR_RX_TIMEOUT 0x00000400
+#define UDMA_INTR_RX_READY_BUF7 0x00000200
+#define UDMA_INTR_RX_READY_BUF6 0x00000100
+#define UDMA_INTR_RX_READY_BUF5 0x00000080
+#define UDMA_INTR_RX_READY_BUF4 0x00000040
+#define UDMA_INTR_RX_READY_BUF3 0x00000020
+#define UDMA_INTR_RX_READY_BUF2 0x00000010
+#define UDMA_INTR_RX_READY_BUF1 0x00000008
+#define UDMA_INTR_RX_READY_BUF0 0x00000004
+#define UDMA_INTR_RX_READY_MASK 0x000003fc
+#define UDMA_INTR_RX_READY_SHIFT 2
+#define UDMA_INTR_RX_ABORT 0x00000002
+#define UDMA_INTR_RX_DONE 0x00000001
+#define UDMA_INTR_SET 0x04
+#define UDMA_INTR_CLEAR 0x08
+#define UDMA_INTR_MASK_STATUS 0x0c
+#define UDMA_INTR_MASK_SET 0x10
+#define UDMA_INTR_MASK_CLEAR 0x14
+
+
+#define UDMA_RX_INTERRUPTS ( \
+ UDMA_INTR_RX_ERROR | \
+ UDMA_INTR_RX_TIMEOUT | \
+ UDMA_INTR_RX_READY_BUF0 | \
+ UDMA_INTR_RX_READY_BUF1 | \
+ UDMA_INTR_RX_READY_BUF2 | \
+ UDMA_INTR_RX_READY_BUF3 | \
+ UDMA_INTR_RX_READY_BUF4 | \
+ UDMA_INTR_RX_READY_BUF5 | \
+ UDMA_INTR_RX_READY_BUF6 | \
+ UDMA_INTR_RX_READY_BUF7 | \
+ UDMA_INTR_RX_ABORT | \
+ UDMA_INTR_RX_DONE)
+
+#define UDMA_RX_ERR_INTERRUPTS ( \
+ UDMA_INTR_RX_ERROR | \
+ UDMA_INTR_RX_TIMEOUT | \
+ UDMA_INTR_RX_ABORT | \
+ UDMA_INTR_RX_DONE)
+
+#define UDMA_TX_INTERRUPTS ( \
+ UDMA_INTR_TX_ABORT | \
+ UDMA_INTR_TX_DONE)
+
+#define UDMA_IS_RX_INTERRUPT(status) ((status) & UDMA_RX_INTERRUPTS)
+#define UDMA_IS_TX_INTERRUPT(status) ((status) & UDMA_TX_INTERRUPTS)
+
+
+/* Current devices have 8 sets of RX buffer registers */
+#define UDMA_RX_BUFS_COUNT 8
+#define UDMA_RX_BUFS_REG_OFFSET (UDMA_RX_BUF1_PTR_LO - UDMA_RX_BUF0_PTR_LO)
+#define UDMA_RX_BUFx_PTR_LO(x) (UDMA_RX_BUF0_PTR_LO + \
+ ((x) * UDMA_RX_BUFS_REG_OFFSET))
+#define UDMA_RX_BUFx_PTR_HI(x) (UDMA_RX_BUF0_PTR_HI + \
+ ((x) * UDMA_RX_BUFS_REG_OFFSET))
+#define UDMA_RX_BUFx_STATUS(x) (UDMA_RX_BUF0_STATUS + \
+ ((x) * UDMA_RX_BUFS_REG_OFFSET))
+#define UDMA_RX_BUFx_DATA_LEN(x) (UDMA_RX_BUF0_DATA_LEN + \
+ ((x) * UDMA_RX_BUFS_REG_OFFSET))
+
+/* Current devices have 2 sets of TX buffer registers */
+#define UDMA_TX_BUFS_COUNT 2
+#define UDMA_TX_BUFS_REG_OFFSET (UDMA_TX_BUF1_PTR_LO - UDMA_TX_BUF0_PTR_LO)
+#define UDMA_TX_BUFx_PTR_LO(x) (UDMA_TX_BUF0_PTR_LO + \
+ ((x) * UDMA_TX_BUFS_REG_OFFSET))
+#define UDMA_TX_BUFx_PTR_HI(x) (UDMA_TX_BUF0_PTR_HI + \
+ ((x) * UDMA_TX_BUFS_REG_OFFSET))
+#define UDMA_TX_BUFx_STATUS(x) (UDMA_TX_BUF0_STATUS + \
+ ((x) * UDMA_TX_BUFS_REG_OFFSET))
+#define UDMA_TX_BUFx_DATA_LEN(x) (UDMA_TX_BUF0_DATA_LEN + \
+ ((x) * UDMA_TX_BUFS_REG_OFFSET))
+#define UDMA_TX_BUFx_DATA_SENT(x) (UDMA_TX_BUF0_DATA_SENT + \
+ ((x) * UDMA_TX_BUFS_REG_OFFSET))
+#define REGS_8250 0
+#define REGS_DMA_RX 1
+#define REGS_DMA_TX 2
+#define REGS_DMA_ISR 3
+#define REGS_DMA_ARB 4
+#define REGS_MAX 5
+
+#define TX_BUF_SIZE 4096
+#define RX_BUF_SIZE 4096
+#define RX_BUFS_COUNT 2
+#define KHZ 1000
+#define MHZ(x) ((x) * KHZ * KHZ)
+
+static const u32 brcmstb_rate_table[] = {
+ MHZ(81),
+ MHZ(108),
+ MHZ(64), /* Actually 64285715 for some chips */
+ MHZ(48),
+};
+
+static const u32 brcmstb_rate_table_7278[] = {
+ MHZ(81),
+ MHZ(108),
+ 0,
+ MHZ(48),
+};
+
+struct brcmuart_priv {
+ int line;
+ struct clk *baud_mux_clk;
+ unsigned long default_mux_rate;
+ u32 real_rates[ARRAY_SIZE(brcmstb_rate_table)];
+ const u32 *rate_table;
+ ktime_t char_wait;
+ struct uart_port *up;
+ struct hrtimer hrt;
+ bool shutdown;
+ bool dma_enabled;
+ struct uart_8250_dma dma;
+ void __iomem *regs[REGS_MAX];
+ dma_addr_t rx_addr;
+ void *rx_bufs;
+ size_t rx_size;
+ int rx_next_buf;
+ dma_addr_t tx_addr;
+ void *tx_buf;
+ size_t tx_size;
+ bool tx_running;
+ bool rx_running;
+ struct dentry *debugfs_dir;
+ struct dentry *debugfs_file;
+
+ /* stats exposed through debugfs */
+ u64 dma_rx_partial_buf;
+ u64 dma_rx_full_buf;
+ u32 rx_bad_timeout_late_char;
+ u32 rx_bad_timeout_no_char;
+ u32 rx_missing_close_timeout;
+ u32 rx_err;
+ u32 rx_timeout;
+ u32 rx_abort;
+};
+
+struct dentry *brcmuart_debugfs_root;
+
+/*
+ * Register access routines
+ */
+static u32 udma_readl(struct brcmuart_priv *priv,
+ int reg_type, int offset)
+{
+ return readl(priv->regs[reg_type] + offset);
+}
+
+static void udma_writel(struct brcmuart_priv *priv,
+ int reg_type, int offset, u32 value)
+{
+ writel(value, priv->regs[reg_type] + offset);
+}
+
+static void udma_set(struct brcmuart_priv *priv,
+ int reg_type, int offset, u32 bits)
+{
+ void __iomem *reg = priv->regs[reg_type] + offset;
+ u32 value;
+
+ value = readl(reg);
+ value |= bits;
+ writel(value, reg);
+}
+
+static void udma_unset(struct brcmuart_priv *priv,
+ int reg_type, int offset, u32 bits)
+{
+ void __iomem *reg = priv->regs[reg_type] + offset;
+ u32 value;
+
+ value = readl(reg);
+ value &= ~bits;
+ writel(value, reg);
+}
+
+/*
+ * The UART DMA engine hardware can be used by multiple UARTS, but
+ * only one at a time. Sharing is not currently supported so
+ * the first UART to request the DMA engine will get it and any
+ * subsequent requests by other UARTS will fail.
+ */
+static int brcmuart_arbitration(struct brcmuart_priv *priv, bool acquire)
+{
+ u32 rx_grant;
+ u32 tx_grant;
+ int waits;
+ int ret = 0;
+
+ if (acquire) {
+ udma_set(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ);
+ udma_set(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ);
+
+ waits = 1;
+ while (1) {
+ rx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_RX);
+ tx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_TX);
+ if (rx_grant & tx_grant & UDMA_ARB_GRANT)
+ return 0;
+ if (waits-- == 0)
+ break;
+ msleep(1);
+ }
+ ret = 1;
+ }
+
+ udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ);
+ udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ);
+ return ret;
+}
+
+static void brcmuart_init_dma_hardware(struct brcmuart_priv *priv)
+{
+ u32 daddr;
+ u32 value;
+ int x;
+
+ /* Start with all interrupts disabled */
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, 0xffffffff);
+
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_SIZE, RX_BUF_SIZE);
+
+ /*
+ * Setup buffer close to happen when 32 character times have
+ * elapsed since the last character was received.
+ */
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_CLOSE, 16*10*32);
+ value = (RX_BUFS_COUNT << UDMA_RX_CTRL_NUM_BUF_USED_SHIFT)
+ | UDMA_RX_CTRL_BUF_CLOSE_MODE
+ | UDMA_RX_CTRL_BUF_CLOSE_ENA;
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_CTRL, value);
+
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_BLOCKOUT_COUNTER, 0);
+ daddr = priv->rx_addr;
+ for (x = 0; x < RX_BUFS_COUNT; x++) {
+
+ /* Set RX transfer length to 0 for unknown */
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_TRANSFER_LEN, 0);
+
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_LO(x),
+ lower_32_bits(daddr));
+ udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_HI(x),
+ upper_32_bits(daddr));
+ daddr += RX_BUF_SIZE;
+ }
+
+ daddr = priv->tx_addr;
+ udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_LO(0),
+ lower_32_bits(daddr));
+ udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_HI(0),
+ upper_32_bits(daddr));
+ udma_writel(priv, REGS_DMA_TX, UDMA_TX_CTRL,
+ UDMA_TX_CTRL_NUM_BUF_USED_1);
+
+ /* clear all interrupts then enable them */
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, 0xffffffff);
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR,
+ UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS);
+
+}
+
+static void start_rx_dma(struct uart_8250_port *p)
+{
+ struct brcmuart_priv *priv = p->port.private_data;
+ int x;
+
+ udma_unset(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA);
+
+ /* Clear the RX ready bit for all buffers */
+ for (x = 0; x < RX_BUFS_COUNT; x++)
+ udma_unset(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(x),
+ UDMA_RX_BUFX_STATUS_DATA_RDY);
+
+ /* always start with buffer 0 */
+ udma_unset(priv, REGS_DMA_RX, UDMA_RX_STATUS,
+ UDMA_RX_STATUS_ACTIVE_BUF_MASK);
+ priv->rx_next_buf = 0;
+
+ udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA);
+ priv->rx_running = true;
+}
+
+static void stop_rx_dma(struct uart_8250_port *p)
+{
+ struct brcmuart_priv *priv = p->port.private_data;
+
+ /* If RX is running, set the RX ABORT */
+ if (priv->rx_running)
+ udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ABORT);
+}
+
+static int stop_tx_dma(struct uart_8250_port *p)
+{
+ struct brcmuart_priv *priv = p->port.private_data;
+ u32 value;
+
+ /* If TX is running, set the TX ABORT */
+ value = udma_readl(priv, REGS_DMA_TX, UDMA_TX_CTRL);
+ if (value & UDMA_TX_CTRL_ENA)
+ udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ABORT);
+ priv->tx_running = false;
+ return 0;
+}
+
+/*
+ * NOTE: printk's in this routine will hang the system if this is
+ * the console tty
+ */
+static int brcmuart_tx_dma(struct uart_8250_port *p)
+{
+ struct brcmuart_priv *priv = p->port.private_data;
+ struct circ_buf *xmit = &p->port.state->xmit;
+ u32 tx_size;
+
+ if (uart_tx_stopped(&p->port) || priv->tx_running ||
+ uart_circ_empty(xmit)) {
+ return 0;
+ }
+ tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
+
+ priv->dma.tx_err = 0;
+ memcpy(priv->tx_buf, &xmit->buf[xmit->tail], tx_size);
+ xmit->tail += tx_size;
+ xmit->tail &= UART_XMIT_SIZE - 1;
+ p->port.icount.tx += tx_size;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&p->port);
+
+ udma_writel(priv, REGS_DMA_TX, UDMA_TX_TRANSFER_LEN, tx_size);
+ udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUF0_DATA_LEN, tx_size);
+ udma_unset(priv, REGS_DMA_TX, UDMA_TX_BUF0_STATUS, UDMA_TX_BUFX_EMPTY);
+ udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ENA);
+ priv->tx_running = true;
+
+ return 0;
+}
+
+static void brcmuart_rx_buf_done_isr(struct uart_port *up, int index)
+{
+ struct brcmuart_priv *priv = up->private_data;
+ struct tty_port *tty_port = &up->state->port;
+ u32 status;
+ u32 length;
+ u32 copied;
+
+ /* Make sure we're still in sync with the hardware */
+ status = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(index));
+ length = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_DATA_LEN(index));
+
+ if ((status & UDMA_RX_BUFX_STATUS_DATA_RDY) == 0) {
+ dev_err(up->dev, "RX done interrupt but DATA_RDY not found\n");
+ return;
+ }
+ if (status & (UDMA_RX_BUFX_STATUS_OVERRUN_ERR |
+ UDMA_RX_BUFX_STATUS_FRAME_ERR |
+ UDMA_RX_BUFX_STATUS_PARITY_ERR)) {
+ if (status & UDMA_RX_BUFX_STATUS_OVERRUN_ERR) {
+ up->icount.overrun++;
+ dev_warn(up->dev, "RX OVERRUN Error\n");
+ }
+ if (status & UDMA_RX_BUFX_STATUS_FRAME_ERR) {
+ up->icount.frame++;
+ dev_warn(up->dev, "RX FRAMING Error\n");
+ }
+ if (status & UDMA_RX_BUFX_STATUS_PARITY_ERR) {
+ up->icount.parity++;
+ dev_warn(up->dev, "RX PARITY Error\n");
+ }
+ }
+ copied = (u32)tty_insert_flip_string(
+ tty_port,
+ priv->rx_bufs + (index * RX_BUF_SIZE),
+ length);
+ if (copied != length) {
+ dev_warn(up->dev, "Flip buffer overrun of %d bytes\n",
+ length - copied);
+ up->icount.overrun += length - copied;
+ }
+ up->icount.rx += length;
+ if (status & UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED)
+ priv->dma_rx_partial_buf++;
+ else if (length != RX_BUF_SIZE)
+ /*
+ * This is a bug in the controller that doesn't cause
+ * any problems but will be fixed in the future.
+ */
+ priv->rx_missing_close_timeout++;
+ else
+ priv->dma_rx_full_buf++;
+
+ tty_flip_buffer_push(tty_port);
+}
+
+static void brcmuart_rx_isr(struct uart_port *up, u32 rx_isr)
+{
+ struct brcmuart_priv *priv = up->private_data;
+ struct device *dev = up->dev;
+ u32 rx_done_isr;
+ u32 check_isr;
+
+ rx_done_isr = (rx_isr & UDMA_INTR_RX_READY_MASK);
+ while (rx_done_isr) {
+ check_isr = UDMA_INTR_RX_READY_BUF0 << priv->rx_next_buf;
+ if (check_isr & rx_done_isr) {
+ brcmuart_rx_buf_done_isr(up, priv->rx_next_buf);
+ } else {
+ dev_err(dev,
+ "RX buffer ready out of sequence, restarting RX DMA\n");
+ start_rx_dma(up_to_u8250p(up));
+ break;
+ }
+ if (rx_isr & UDMA_RX_ERR_INTERRUPTS) {
+ if (rx_isr & UDMA_INTR_RX_ERROR)
+ priv->rx_err++;
+ if (rx_isr & UDMA_INTR_RX_TIMEOUT) {
+ priv->rx_timeout++;
+ dev_err(dev, "RX TIMEOUT Error\n");
+ }
+ if (rx_isr & UDMA_INTR_RX_ABORT)
+ priv->rx_abort++;
+ priv->rx_running = false;
+ }
+ /* If not ABORT, re-enable RX buffer */
+ if (!(rx_isr & UDMA_INTR_RX_ABORT))
+ udma_unset(priv, REGS_DMA_RX,
+ UDMA_RX_BUFx_STATUS(priv->rx_next_buf),
+ UDMA_RX_BUFX_STATUS_DATA_RDY);
+ rx_done_isr &= ~check_isr;
+ priv->rx_next_buf++;
+ if (priv->rx_next_buf == RX_BUFS_COUNT)
+ priv->rx_next_buf = 0;
+ }
+}
+
+static void brcmuart_tx_isr(struct uart_port *up, u32 isr)
+{
+ struct brcmuart_priv *priv = up->private_data;
+ struct device *dev = up->dev;
+ struct uart_8250_port *port_8250 = up_to_u8250p(up);
+ struct circ_buf *xmit = &port_8250->port.state->xmit;
+ int length;
+
+ length = udma_readl(priv, REGS_DMA_TX, UDMA_TX_TRANSFER_TOTAL);
+ if (isr & UDMA_INTR_TX_ABORT) {
+ if (priv->tx_running)
+ dev_err(dev, "Unexpected TX_ABORT interrupt\n");
+ return;
+ }
+ priv->tx_running = false;
+ if (!uart_circ_empty(xmit) && !uart_tx_stopped(up))
+ brcmuart_tx_dma(port_8250);
+}
+
+static irqreturn_t brcmuart_isr(int irq, void *dev_id)
+{
+ struct uart_port *up = dev_id;
+ struct device *dev = up->dev;
+ struct brcmuart_priv *priv = up->private_data;
+ unsigned long flags;
+ u32 interrupts;
+ u32 rval;
+ u32 tval;
+
+ interrupts = udma_readl(priv, REGS_DMA_ISR, UDMA_INTR_STATUS);
+ if (interrupts == 0)
+ return IRQ_NONE;
+
+ spin_lock_irqsave(&up->lock, flags);
+
+ /* Clear all interrupts */
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, interrupts);
+
+ rval = UDMA_IS_RX_INTERRUPT(interrupts);
+ if (rval)
+ brcmuart_rx_isr(up, rval);
+ tval = UDMA_IS_TX_INTERRUPT(interrupts);
+ if (tval)
+ brcmuart_tx_isr(up, tval);
+ if ((rval | tval) == 0)
+ dev_warn(dev, "Spurious interrupt: 0x%x\n", interrupts);
+
+ spin_unlock_irqrestore(&up->lock, flags);
+ return IRQ_HANDLED;
+}
+
+static int brcmuart_startup(struct uart_port *port)
+{
+ int res;
+ struct uart_8250_port *up = up_to_u8250p(port);
+ struct brcmuart_priv *priv = up->port.private_data;
+
+ priv->shutdown = false;
+
+ /*
+ * prevent serial8250_do_startup() from allocating non-existent
+ * DMA resources
+ */
+ up->dma = NULL;
+
+ res = serial8250_do_startup(port);
+ if (!priv->dma_enabled)
+ return res;
+ /*
+ * Disable the Receive Data Interrupt because the DMA engine
+ * will handle this.
+ */
+ up->ier &= ~UART_IER_RDI;
+ serial_port_out(port, UART_IER, up->ier);
+
+ priv->tx_running = false;
+ priv->dma.rx_dma = NULL;
+ priv->dma.tx_dma = brcmuart_tx_dma;
+ up->dma = &priv->dma;
+
+ brcmuart_init_dma_hardware(priv);
+ start_rx_dma(up);
+ return res;
+}
+
+static void brcmuart_shutdown(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ struct brcmuart_priv *priv = up->port.private_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ priv->shutdown = true;
+ if (priv->dma_enabled) {
+ stop_rx_dma(up);
+ stop_tx_dma(up);
+ /* disable all interrupts */
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET,
+ UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS);
+ }
+
+ /*
+ * prevent serial8250_do_shutdown() from trying to free
+ * DMA resources that we never alloc'd for this driver.
+ */
+ up->dma = NULL;
+
+ spin_unlock_irqrestore(&port->lock, flags);
+ serial8250_do_shutdown(port);
+}
+
+/*
+ * Not all clocks run at the exact specified rate, so set each requested
+ * rate and then get the actual rate.
+ */
+static void init_real_clk_rates(struct device *dev, struct brcmuart_priv *priv)
+{
+ int x;
+ int rc;
+
+ priv->default_mux_rate = clk_get_rate(priv->baud_mux_clk);
+ for (x = 0; x < ARRAY_SIZE(priv->real_rates); x++) {
+ if (priv->rate_table[x] == 0) {
+ priv->real_rates[x] = 0;
+ continue;
+ }
+ rc = clk_set_rate(priv->baud_mux_clk, priv->rate_table[x]);
+ if (rc) {
+ dev_err(dev, "Error selecting BAUD MUX clock for %u\n",
+ priv->rate_table[x]);
+ priv->real_rates[x] = priv->rate_table[x];
+ } else {
+ priv->real_rates[x] = clk_get_rate(priv->baud_mux_clk);
+ }
+ }
+ clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate);
+}
+
+static void set_clock_mux(struct uart_port *up, struct brcmuart_priv *priv,
+ u32 baud)
+{
+ u32 percent;
+ u32 best_percent = UINT_MAX;
+ u32 quot;
+ u32 best_quot = 1;
+ u32 rate;
+ int best_index = -1;
+ u64 hires_rate;
+ u64 hires_baud;
+ u64 hires_err;
+ int rc;
+ int i;
+ int real_baud;
+
+ /* If the Baud Mux Clock was not specified, just return */
+ if (priv->baud_mux_clk == NULL)
+ return;
+
+ /* Find the closest match for specified baud */
+ for (i = 0; i < ARRAY_SIZE(priv->real_rates); i++) {
+ if (priv->real_rates[i] == 0)
+ continue;
+ rate = priv->real_rates[i] / 16;
+ quot = DIV_ROUND_CLOSEST(rate, baud);
+ if (!quot)
+ continue;
+
+ /* increase resolution to get xx.xx percent */
+ hires_rate = (u64)rate * 10000;
+ hires_baud = (u64)baud * 10000;
+
+ hires_err = div_u64(hires_rate, (u64)quot);
+
+ /* get the delta */
+ if (hires_err > hires_baud)
+ hires_err = (hires_err - hires_baud);
+ else
+ hires_err = (hires_baud - hires_err);
+
+ percent = (unsigned long)DIV_ROUND_CLOSEST_ULL(hires_err, baud);
+ dev_dbg(up->dev,
+ "Baud rate: %u, MUX Clk: %u, Error: %u.%u%%\n",
+ baud, priv->real_rates[i], percent / 100,
+ percent % 100);
+ if (percent < best_percent) {
+ best_percent = percent;
+ best_index = i;
+ best_quot = quot;
+ }
+ }
+ if (best_index == -1) {
+ dev_err(up->dev, "Error, %d BAUD rate is too fast.\n", baud);
+ return;
+ }
+ rate = priv->real_rates[best_index];
+ rc = clk_set_rate(priv->baud_mux_clk, rate);
+ if (rc)
+ dev_err(up->dev, "Error selecting BAUD MUX clock\n");
+
+ /* Error over 3 percent will cause data errors */
+ if (best_percent > 300)
+ dev_err(up->dev, "Error, baud: %d has %u.%u%% error\n",
+ baud, percent / 100, percent % 100);
+
+ real_baud = rate / 16 / best_quot;
+ dev_dbg(up->dev, "Selecting BAUD MUX rate: %u\n", rate);
+ dev_dbg(up->dev, "Requested baud: %u, Actual baud: %u\n",
+ baud, real_baud);
+
+ /* calc nanoseconds for 1.5 characters time at the given baud rate */
+ i = NSEC_PER_SEC / real_baud / 10;
+ i += (i / 2);
+ priv->char_wait = ns_to_ktime(i);
+
+ up->uartclk = rate;
+}
+
+static void brcmstb_set_termios(struct uart_port *up,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct uart_8250_port *p8250 = up_to_u8250p(up);
+ struct brcmuart_priv *priv = up->private_data;
+
+ if (priv->dma_enabled)
+ stop_rx_dma(p8250);
+ set_clock_mux(up, priv, tty_termios_baud_rate(termios));
+ serial8250_do_set_termios(up, termios, old);
+ if (p8250->mcr & UART_MCR_AFE)
+ p8250->port.status |= UPSTAT_AUTOCTS;
+ if (priv->dma_enabled)
+ start_rx_dma(p8250);
+}
+
+static int brcmuart_handle_irq(struct uart_port *p)
+{
+ unsigned int iir = serial_port_in(p, UART_IIR);
+ struct brcmuart_priv *priv = p->private_data;
+ struct uart_8250_port *up = up_to_u8250p(p);
+ unsigned int status;
+ unsigned long flags;
+ unsigned int ier;
+ unsigned int mcr;
+ int handled = 0;
+
+ /*
+ * There's a bug in some 8250 cores where we get a timeout
+ * interrupt but there is no data ready.
+ */
+ if (((iir & UART_IIR_ID) == UART_IIR_RX_TIMEOUT) && !(priv->shutdown)) {
+ spin_lock_irqsave(&p->lock, flags);
+ status = serial_port_in(p, UART_LSR);
+ if ((status & UART_LSR_DR) == 0) {
+
+ ier = serial_port_in(p, UART_IER);
+ /*
+ * if Receive Data Interrupt is enabled and
+ * we're uing hardware flow control, deassert
+ * RTS and wait for any chars in the pipline to
+ * arrive and then check for DR again.
+ */
+ if ((ier & UART_IER_RDI) && (up->mcr & UART_MCR_AFE)) {
+ ier &= ~(UART_IER_RLSI | UART_IER_RDI);
+ serial_port_out(p, UART_IER, ier);
+ mcr = serial_port_in(p, UART_MCR);
+ mcr &= ~UART_MCR_RTS;
+ serial_port_out(p, UART_MCR, mcr);
+ hrtimer_start(&priv->hrt, priv->char_wait,
+ HRTIMER_MODE_REL);
+ } else {
+ serial_port_in(p, UART_RX);
+ }
+
+ handled = 1;
+ }
+ spin_unlock_irqrestore(&p->lock, flags);
+ if (handled)
+ return 1;
+ }
+ return serial8250_handle_irq(p, iir);
+}
+
+static enum hrtimer_restart brcmuart_hrtimer_func(struct hrtimer *t)
+{
+ struct brcmuart_priv *priv = container_of(t, struct brcmuart_priv, hrt);
+ struct uart_port *p = priv->up;
+ struct uart_8250_port *up = up_to_u8250p(p);
+ unsigned int status;
+ unsigned long flags;
+
+ if (priv->shutdown)
+ return HRTIMER_NORESTART;
+
+ spin_lock_irqsave(&p->lock, flags);
+ status = serial_port_in(p, UART_LSR);
+
+ /*
+ * If a character did not arrive after the timeout, clear the false
+ * receive timeout.
+ */
+ if ((status & UART_LSR_DR) == 0) {
+ serial_port_in(p, UART_RX);
+ priv->rx_bad_timeout_no_char++;
+ } else {
+ priv->rx_bad_timeout_late_char++;
+ }
+
+ /* re-enable receive unless upper layer has disabled it */
+ if ((up->ier & (UART_IER_RLSI | UART_IER_RDI)) ==
+ (UART_IER_RLSI | UART_IER_RDI)) {
+ status = serial_port_in(p, UART_IER);
+ status |= (UART_IER_RLSI | UART_IER_RDI);
+ serial_port_out(p, UART_IER, status);
+ status = serial_port_in(p, UART_MCR);
+ status |= UART_MCR_RTS;
+ serial_port_out(p, UART_MCR, status);
+ }
+ spin_unlock_irqrestore(&p->lock, flags);
+ return HRTIMER_NORESTART;
+}
+
+static const struct of_device_id brcmuart_dt_ids[] = {
+ {
+ .compatible = "brcm,bcm7278-uart",
+ .data = brcmstb_rate_table_7278,
+ },
+ {
+ .compatible = "brcm,bcm7271-uart",
+ .data = brcmstb_rate_table,
+ },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, brcmuart_dt_ids);
+
+static void brcmuart_free_bufs(struct device *dev, struct brcmuart_priv *priv)
+{
+ if (priv->rx_bufs)
+ dma_free_coherent(dev, priv->rx_size, priv->rx_bufs,
+ priv->rx_addr);
+ if (priv->tx_buf)
+ dma_free_coherent(dev, priv->tx_size, priv->tx_buf,
+ priv->tx_addr);
+}
+
+static void brcmuart_throttle(struct uart_port *port)
+{
+ struct brcmuart_priv *priv = port->private_data;
+
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, UDMA_RX_INTERRUPTS);
+}
+
+static void brcmuart_unthrottle(struct uart_port *port)
+{
+ struct brcmuart_priv *priv = port->private_data;
+
+ udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR,
+ UDMA_RX_INTERRUPTS);
+}
+
+static int debugfs_stats_show(struct seq_file *s, void *unused)
+{
+ struct brcmuart_priv *priv = s->private;
+
+ seq_printf(s, "rx_err:\t\t\t\t%u\n",
+ priv->rx_err);
+ seq_printf(s, "rx_timeout:\t\t\t%u\n",
+ priv->rx_timeout);
+ seq_printf(s, "rx_abort:\t\t\t%u\n",
+ priv->rx_abort);
+ seq_printf(s, "rx_bad_timeout_late_char:\t%u\n",
+ priv->rx_bad_timeout_late_char);
+ seq_printf(s, "rx_bad_timeout_no_char:\t\t%u\n",
+ priv->rx_bad_timeout_no_char);
+ seq_printf(s, "rx_missing_close_timeout:\t%u\n",
+ priv->rx_missing_close_timeout);
+ if (priv->dma_enabled) {
+ seq_printf(s, "dma_rx_partial_buf:\t\t%llu\n",
+ priv->dma_rx_partial_buf);
+ seq_printf(s, "dma_rx_full_buf:\t\t%llu\n",
+ priv->dma_rx_full_buf);
+ }
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(debugfs_stats);
+
+static void brcmuart_init_debugfs(struct brcmuart_priv *priv,
+ const char *device)
+{
+ priv->debugfs_dir = debugfs_create_dir(device, brcmuart_debugfs_root);
+ priv->debugfs_file = debugfs_create_file("stats", 0444,
+ priv->debugfs_dir,
+ priv,
+ &debugfs_stats_fops);
+}
+
+
+static int brcmuart_probe(struct platform_device *pdev)
+{
+ struct resource *regs;
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *of_id = NULL;
+ struct uart_8250_port *new_port;
+ struct device *dev = &pdev->dev;
+ struct brcmuart_priv *priv;
+ struct clk *baud_mux_clk;
+ struct uart_8250_port up;
+ struct resource *irq;
+ void __iomem *membase = 0;
+ resource_size_t mapbase = 0;
+ u32 clk_rate = 0;
+ int ret;
+ int x;
+ int dma_irq;
+ static const char * const reg_names[REGS_MAX] = {
+ "uart", "dma_rx", "dma_tx", "dma_intr2", "dma_arb"
+ };
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!irq) {
+ dev_err(dev, "missing irq\n");
+ return -EINVAL;
+ }
+ priv = devm_kzalloc(dev, sizeof(struct brcmuart_priv),
+ GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ of_id = of_match_node(brcmuart_dt_ids, np);
+ if (!of_id || !of_id->data)
+ priv->rate_table = brcmstb_rate_table;
+ else
+ priv->rate_table = of_id->data;
+
+ for (x = 0; x < REGS_MAX; x++) {
+ regs = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ reg_names[x]);
+ if (!regs)
+ break;
+ priv->regs[x] = devm_ioremap(dev, regs->start,
+ resource_size(regs));
+ if (IS_ERR(priv->regs[x]))
+ return PTR_ERR(priv->regs[x]);
+ if (x == REGS_8250) {
+ mapbase = regs->start;
+ membase = priv->regs[x];
+ }
+ }
+
+ /* We should have just the uart base registers or all the registers */
+ if (x != 1 && x != REGS_MAX) {
+ dev_warn(dev, "%s registers not specified\n", reg_names[x]);
+ return -EINVAL;
+ }
+
+ /* if the DMA registers were specified, try to enable DMA */
+ if (x > REGS_DMA_RX) {
+ if (brcmuart_arbitration(priv, 1) == 0) {
+ u32 txrev = 0;
+ u32 rxrev = 0;
+
+ txrev = udma_readl(priv, REGS_DMA_RX, UDMA_RX_REVISION);
+ rxrev = udma_readl(priv, REGS_DMA_TX, UDMA_TX_REVISION);
+ if ((txrev >= UDMA_TX_REVISION_REQUIRED) &&
+ (rxrev >= UDMA_RX_REVISION_REQUIRED)) {
+
+ /* Enable the use of the DMA hardware */
+ priv->dma_enabled = true;
+ } else {
+ brcmuart_arbitration(priv, 0);
+ dev_err(dev,
+ "Unsupported DMA Hardware Revision\n");
+ }
+ } else {
+ dev_err(dev,
+ "Timeout arbitrating for UART DMA hardware\n");
+ }
+ }
+
+ of_property_read_u32(np, "clock-frequency", &clk_rate);
+
+ /* See if a Baud clock has been specified */
+ baud_mux_clk = of_clk_get_by_name(np, "sw_baud");
+ if (IS_ERR(baud_mux_clk)) {
+ if (PTR_ERR(baud_mux_clk) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ dev_info(dev, "BAUD MUX clock not specified\n");
+ } else {
+ dev_info(dev, "BAUD MUX clock found\n");
+ ret = clk_prepare_enable(baud_mux_clk);
+ if (ret)
+ return ret;
+ priv->baud_mux_clk = baud_mux_clk;
+ init_real_clk_rates(dev, priv);
+ clk_rate = priv->default_mux_rate;
+ }
+
+ if (clk_rate == 0) {
+ dev_err(dev, "clock-frequency or clk not defined\n");
+ return -EINVAL;
+ }
+
+ dev_info(dev, "DMA is %senabled\n", priv->dma_enabled ? "" : "not ");
+
+ memset(&up, 0, sizeof(up));
+ up.port.type = PORT_16550A;
+ up.port.uartclk = clk_rate;
+ up.port.dev = dev;
+ up.port.mapbase = mapbase;
+ up.port.membase = membase;
+ up.port.irq = irq->start;
+ up.port.handle_irq = brcmuart_handle_irq;
+ up.port.regshift = 2;
+ up.port.iotype = of_device_is_big_endian(np) ?
+ UPIO_MEM32BE : UPIO_MEM32;
+ up.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF
+ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
+ up.port.dev = dev;
+ up.port.private_data = priv;
+ up.capabilities = UART_CAP_FIFO | UART_CAP_AFE;
+ up.port.fifosize = 32;
+
+ /* Check for a fixed line number */
+ ret = of_alias_get_id(np, "serial");
+ if (ret >= 0)
+ up.port.line = ret;
+
+ /* setup HR timer */
+ hrtimer_init(&priv->hrt, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
+ priv->hrt.function = brcmuart_hrtimer_func;
+
+ up.port.shutdown = brcmuart_shutdown;
+ up.port.startup = brcmuart_startup;
+ up.port.throttle = brcmuart_throttle;
+ up.port.unthrottle = brcmuart_unthrottle;
+ up.port.set_termios = brcmstb_set_termios;
+
+ if (priv->dma_enabled) {
+ priv->rx_size = RX_BUF_SIZE * RX_BUFS_COUNT;
+ priv->rx_bufs = dma_alloc_coherent(dev,
+ priv->rx_size,
+ &priv->rx_addr, GFP_KERNEL);
+ if (!priv->rx_bufs)
+ goto err;
+ priv->tx_size = UART_XMIT_SIZE;
+ priv->tx_buf = dma_alloc_coherent(dev,
+ priv->tx_size,
+ &priv->tx_addr, GFP_KERNEL);
+ if (!priv->tx_buf)
+ goto err;
+ }
+
+ ret = serial8250_register_8250_port(&up);
+ if (ret < 0) {
+ dev_err(dev, "unable to register 8250 port\n");
+ goto err;
+ }
+ priv->line = ret;
+ new_port = serial8250_get_port(ret);
+ priv->up = &new_port->port;
+ if (priv->dma_enabled) {
+ dma_irq = platform_get_irq_byname(pdev, "dma");
+ if (dma_irq < 0) {
+ dev_err(dev, "no IRQ resource info\n");
+ goto err1;
+ }
+ ret = devm_request_irq(dev, dma_irq, brcmuart_isr,
+ IRQF_SHARED, "uart DMA irq", &new_port->port);
+ if (ret) {
+ dev_err(dev, "unable to register IRQ handler\n");
+ goto err1;
+ }
+ }
+ platform_set_drvdata(pdev, priv);
+ brcmuart_init_debugfs(priv, dev_name(&pdev->dev));
+ return 0;
+
+err1:
+ serial8250_unregister_port(priv->line);
+err:
+ brcmuart_free_bufs(dev, priv);
+ brcmuart_arbitration(priv, 0);
+ return -ENODEV;
+}
+
+static int brcmuart_remove(struct platform_device *pdev)
+{
+ struct brcmuart_priv *priv = platform_get_drvdata(pdev);
+
+ debugfs_remove_recursive(priv->debugfs_dir);
+ hrtimer_cancel(&priv->hrt);
+ serial8250_unregister_port(priv->line);
+ brcmuart_free_bufs(&pdev->dev, priv);
+ brcmuart_arbitration(priv, 0);
+ return 0;
+}
+
+static int __maybe_unused brcmuart_suspend(struct device *dev)
+{
+ struct brcmuart_priv *priv = dev_get_drvdata(dev);
+
+ serial8250_suspend_port(priv->line);
+ clk_disable_unprepare(priv->baud_mux_clk);
+
+ return 0;
+}
+
+static int __maybe_unused brcmuart_resume(struct device *dev)
+{
+ struct brcmuart_priv *priv = dev_get_drvdata(dev);
+ int ret;
+
+ ret = clk_prepare_enable(priv->baud_mux_clk);
+ if (ret)
+ dev_err(dev, "Error enabling BAUD MUX clock\n");
+
+ /*
+ * The hardware goes back to it's default after suspend
+ * so get the "clk" back in sync.
+ */
+ ret = clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate);
+ if (ret)
+ dev_err(dev, "Error restoring default BAUD MUX clock\n");
+ if (priv->dma_enabled) {
+ if (brcmuart_arbitration(priv, 1)) {
+ dev_err(dev, "Timeout arbitrating for DMA hardware on resume\n");
+ return(-EBUSY);
+ }
+ brcmuart_init_dma_hardware(priv);
+ start_rx_dma(serial8250_get_port(priv->line));
+ }
+ serial8250_resume_port(priv->line);
+ return 0;
+}
+
+static const struct dev_pm_ops brcmuart_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(brcmuart_suspend, brcmuart_resume)
+};
+
+static struct platform_driver brcmuart_platform_driver = {
+ .driver = {
+ .name = "bcm7271-uart",
+ .pm = &brcmuart_dev_pm_ops,
+ .of_match_table = brcmuart_dt_ids,
+ },
+ .probe = brcmuart_probe,
+ .remove = brcmuart_remove,
+};
+
+int __init brcmuart_init(void)
+{
+ brcmuart_debugfs_root = debugfs_create_dir(
+ brcmuart_platform_driver.driver.name, NULL);
+ return platform_driver_register(&brcmuart_platform_driver);
+}
+module_init(brcmuart_init);
+
+void __exit brcmuart_deinit(void)
+{
+ platform_driver_unregister(&brcmuart_platform_driver);
+ debugfs_remove_recursive(brcmuart_debugfs_root);
+}
+module_exit(brcmuart_deinit);
+
+MODULE_AUTHOR("Al Cooper");
+MODULE_DESCRIPTION("Broadcom NS16550A compatible serial port driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 603137da4736..d8891d03e8d1 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -510,6 +510,16 @@ config SERIAL_8250_TEGRA
Select this option if you have machine with an NVIDIA Tegra SoC and
wish to enable 8250 serial driver for the Tegra serial interfaces.
+config SERIAL_8250_BCM7271
+ bool "Broadcom 8250 based serial port"
+ depends on SERIAL_8250 && (ARCH_BRCMSTB || COMPILE_TEST)
+ default ARCH_BRCMSTB
+ help
+ If you have a Broadcom STB based board and want to use the
+ enhanced features of the Broadcom 8250 based serial port,
+ including DMA support and high accuracy BAUD rates, say
+ Y to this option. If unsure, say N.
+
config SERIAL_OF_PLATFORM
tristate "Devicetree based probing for 8250 ports"
depends on SERIAL_8250 && OF
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index a8bfb654d490..b9bcd73c8997 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o
obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o
obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o
obj-$(CONFIG_SERIAL_8250_TEGRA) += 8250_tegra.o
+obj-$(CONFIG_SERIAL_8250_BCM7271) += 8250_bcm7271.o
obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o
CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt
--
2.17.1
Powered by blists - more mailing lists