| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210308195408.48aea2a5@archlinux>
Date: Mon, 8 Mar 2021 19:54:08 +0000
From: Jonathan Cameron <jic23@...nel.org>
To: <Eugen.Hristev@...rochip.com>
Cc: <robh+dt@...nel.org>, <Ludovic.Desroches@...rochip.com>,
<linux-iio@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 4/4] iio: adc: at91-sama5d2: add support for sama7g5
device
On Mon, 8 Mar 2021 13:27:48 +0000
<Eugen.Hristev@...rochip.com> wrote:
> On 06.03.2021 19:30, Jonathan Cameron wrote:
> > On Mon, 1 Mar 2021 16:32:56 +0200
> > Eugen Hristev <eugen.hristev@...rochip.com> wrote:
> >
> >> Add support to sama7g5 ADC which is similar with sama5d2/sam9x60 device.
> >> Differences are highlighted by compatible.
> >> Main differences include 16 channels instead of 12 and missing
> >> resistive touchscreen.
> >>
> >> Signed-off-by: Eugen Hristev <eugen.hristev@...rochip.com>
> >
> > Hi Eugen,
> >
> > What tends to end up cleaner than the many scattered places you have
> > had to bolt in part support here, is to use a per device type constant
> > structure. That structure can contain register addresses where that
> > is all the differs between parts, and callbacks for more complex cases.
> >
> > Along the lines of
> >
> > static const struct sam5d2_chip_info sam5d2_inf {
> > .eoc_register = 0x33,
> > .max_chan_idx = bob,
> > .ccr = bob_function,
> > ...
> > };
> >
> > Then you can just put a pointer to this in the match_data and look that
> > up in probe
>
> Hi Jonathan,
>
>
> Could you have a look a little at this driver though:
>
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/watchdog/sama5d4_wdt.c
>
> The specific support for 'sam9x60' was added by me, and the driver does
> not look so bad after all, having if/else clauses nearly everywhere, and
> getting that 'sam9x60_supported' bit from the compatible string comparison.
>
> That's the reason why I tried to have this ADC driver in a similar fashion.
>
> I like your approach as well, I guess it's just a matter of preference.
> I will start to change things to implement it as you suggested if you
> don't say otherwise.
It works, but starts to go wrong once we get to a 3rd type and experience
says there will probably be a 3rd type sooner or later.
Once you hit that then the if / else everywhere begins to get really ugly.
I think I'd prefer to take the long term view and wrap it all up in a structure.
thanks,
Jonathan
>
> Thanks for reviewing,
> Eugen
>
> >
> >> ---
> >> drivers/iio/adc/at91-sama5d2_adc.c | 287 +++++++++++++++++++++++------
> >> 1 file changed, 234 insertions(+), 53 deletions(-)
> >>
> >> diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c
> >> index 066d0ad644ca..d61fa32ef294 100644
> >> --- a/drivers/iio/adc/at91-sama5d2_adc.c
> >> +++ b/drivers/iio/adc/at91-sama5d2_adc.c
> >> @@ -1,9 +1,11 @@
> >> // SPDX-License-Identifier: GPL-2.0-only
> >> /*
> >> - * Atmel ADC driver for SAMA5D2 devices and compatible.
> >> + * Microchip ADC driver for SAMA5D2/SAMA7G5 devices and compatible.
> >> *
> >> * Copyright (C) 2015 Atmel,
> >> - * 2015 Ludovic Desroches <ludovic.desroches@...el.com>
> >> + * 2015 Ludovic Desroches <ludovic.desroches@...rochip.com>,
> >> + * 2021 Microchip Technology, Inc.,
> >> + * 2021 Eugen Hristev <eugen.hristev@...rochip.com>
> >> */
> >>
> >> #include <linux/bitops.h>
> >> @@ -117,14 +119,26 @@
> >> #define AT91_SAMA5D2_ISR 0x30
> >> /* Interrupt Status Register - Pen touching sense status */
> >> #define AT91_SAMA5D2_ISR_PENS BIT(31)
> >> +
> >> +/* End of Conversion Interrupt Enable Register */
> >> +#define AT91_SAMA7G5_EOC_IER 0x34
> >> +/* End of Conversion Interrupt Disable Register */
> >> +#define AT91_SAMA7G5_EOC_IDR 0x38
> >> +/* End of Conversion Interrupt Mask Register */
> >> +#define AT91_SAMA7G5_EOC_IMR 0x3c
> >> +/* End of Conversion Interrupt Status Register */
> >> +#define AT91_SAMA7G5_EOC_ISR 0x40
> >> +
> >> /* Last Channel Trigger Mode Register */
> >> #define AT91_SAMA5D2_LCTMR 0x34
> >> /* Last Channel Compare Window Register */
> >> #define AT91_SAMA5D2_LCCWR 0x38
> >> /* Overrun Status Register */
> >> #define AT91_SAMA5D2_OVER 0x3c
> >> +#define AT91_SAMA7G5_OVER 0x4c
> >> /* Extended Mode Register */
> >> #define AT91_SAMA5D2_EMR 0x40
> >> +#define AT91_SAMA7G5_EMR 0x50
> >> /* Extended Mode Register - Oversampling rate */
> >> #define AT91_SAMA5D2_EMR_OSR(V) ((V) << 16)
> >> #define AT91_SAMA5D2_EMR_OSR_MASK GENMASK(17, 16)
> >> @@ -142,6 +156,9 @@
> >> /* Channel Offset Register */
> >> #define AT91_SAMA5D2_COR 0x4c
> >> #define AT91_SAMA5D2_COR_DIFF_OFFSET 16
> >> +/* Channel Configuration Register */
> >> +#define AT91_SAMA7G5_CCR 0x5c
> >> +#define AT91_SAMA7G5_COR_DIFF_OFFSET 0
> >>
> >> /* Analog Control Register */
> >> #define AT91_SAMA5D2_ACR 0x94
> >> @@ -185,6 +202,7 @@
> >> #define AT91_SAMA5D2_PRESSR 0xbc
> >> /* Trigger Register */
> >> #define AT91_SAMA5D2_TRGR 0xc0
> >> +#define AT91_SAMA7G5_TRGR 0x100
> >> /* Mask for TRGMOD field of TRGR register */
> >> #define AT91_SAMA5D2_TRGR_TRGMOD_MASK GENMASK(2, 0)
> >> /* No trigger, only software trigger can start conversions */
> >> @@ -214,19 +232,26 @@
> >> #define AT91_SAMA5D2_WPSR 0xe8
> >> /* Version Register */
> >> #define AT91_SAMA5D2_VERSION 0xfc
> >> +#define AT91_SAMA7G5_VERSION 0x130
> >>
> >> #define AT91_SAMA5D2_HW_TRIG_CNT 3
> >> #define AT91_SAMA5D2_SINGLE_CHAN_CNT 12
> >> +#define AT91_SAMA7G5_SINGLE_CHAN_CNT 16
> >> #define AT91_SAMA5D2_DIFF_CHAN_CNT 6
> >> +#define AT91_SAMA7G5_DIFF_CHAN_CNT 8
> >>
> >> #define AT91_SAMA5D2_TIMESTAMP_CHAN_IDX (AT91_SAMA5D2_SINGLE_CHAN_CNT + \
> >> AT91_SAMA5D2_DIFF_CHAN_CNT + 1)
> >>
> >> +#define AT91_SAMA7G5_TIMESTAMP_CHAN_IDX (AT91_SAMA7G5_SINGLE_CHAN_CNT + \
> >> + AT91_SAMA7G5_DIFF_CHAN_CNT + 1)
> >> +
> >> #define AT91_SAMA5D2_TOUCH_X_CHAN_IDX (AT91_SAMA5D2_SINGLE_CHAN_CNT + \
> >> AT91_SAMA5D2_DIFF_CHAN_CNT * 2)
> >> #define AT91_SAMA5D2_TOUCH_Y_CHAN_IDX (AT91_SAMA5D2_TOUCH_X_CHAN_IDX + 1)
> >> #define AT91_SAMA5D2_TOUCH_P_CHAN_IDX (AT91_SAMA5D2_TOUCH_Y_CHAN_IDX + 1)
> >> #define AT91_SAMA5D2_MAX_CHAN_IDX AT91_SAMA5D2_TOUCH_P_CHAN_IDX
> >> +#define AT91_SAMA7G5_MAX_CHAN_IDX AT91_SAMA7G5_TIMESTAMP_CHAN_IDX
> >>
> >> #define AT91_SAMA5D2_TOUCH_SAMPLE_PERIOD_US 2000 /* 2ms */
> >> #define AT91_SAMA5D2_TOUCH_PEN_DETECT_DEBOUNCE_US 200
> >> @@ -239,8 +264,19 @@
> >> * Maximum number of bytes to hold conversion from all channels
> >> * without the timestamp.
> >> */
> >> -#define AT91_BUFFER_MAX_CONVERSION_BYTES ((AT91_SAMA5D2_SINGLE_CHAN_CNT + \
> >> - AT91_SAMA5D2_DIFF_CHAN_CNT) * 2)
> >> +#define AT91_SAMA5D2_BUFFER_MAX_CONVERSION_BYTES ( \
> >> + (AT91_SAMA5D2_SINGLE_CHAN_CNT + \
> >> + AT91_SAMA5D2_DIFF_CHAN_CNT) * 2)
> >> +
> >> +#define AT91_SAMA7G5_BUFFER_MAX_CONVERSION_BYTES ( \
> >> + (AT91_SAMA7G5_SINGLE_CHAN_CNT + \
> >> + AT91_SAMA7G5_DIFF_CHAN_CNT) * 2)
> >> +
> >> +#define AT91_BUFFER_MAX_CONVERSION_BYTES ( \
> >> + (AT91_SAMA7G5_BUFFER_MAX_CONVERSION_BYTES > \
> >> + AT91_SAMA5D2_BUFFER_MAX_CONVERSION_BYTES) ? \
> >> + AT91_SAMA7G5_BUFFER_MAX_CONVERSION_BYTES : \
> >> + AT91_SAMA5D2_BUFFER_MAX_CONVERSION_BYTES)
> >>
> >> /* This total must also include the timestamp */
> >> #define AT91_BUFFER_MAX_BYTES (AT91_BUFFER_MAX_CONVERSION_BYTES + 8)
> >> @@ -295,6 +331,27 @@
> >> .indexed = 1, \
> >> }
> >>
> >> +#define AT91_SAMA7G5_CHAN_DIFF(num, num2, addr) \
> >> + { \
> >> + .type = IIO_VOLTAGE, \
> >> + .differential = 1, \
> >> + .channel = num, \
> >> + .channel2 = num2, \
> >> + .address = addr, \
> >> + .scan_index = num + AT91_SAMA7G5_SINGLE_CHAN_CNT, \
> >> + .scan_type = { \
> >> + .sign = 's', \
> >> + .realbits = 14, \
> >> + .storagebits = 16, \
> >> + }, \
> >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> >> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ)|\
> >> + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
> >> + .datasheet_name = "CH"#num"-CH"#num2, \
> >> + .indexed = 1, \
> >> + }
> >> +
> >> #define AT91_SAMA5D2_CHAN_TOUCH(num, name, mod) \
> >> { \
> >> .type = IIO_POSITIONRELATIVE, \
> >> @@ -335,6 +392,8 @@ struct at91_adc_soc_info {
> >> unsigned startup_time;
> >> unsigned min_sample_rate;
> >> unsigned max_sample_rate;
> >> +#define AT91_ADC_SAMA7G5(st) ((st)->soc_info.sama7g5)
> >> + bool sama7g5;
> >> };
> >>
> >> struct at91_adc_trigger {
> >> @@ -436,7 +495,7 @@ static const struct at91_adc_trigger at91_adc_trigger_list[] = {
> >> },
> >> };
> >>
> >> -static const struct iio_chan_spec at91_adc_channels[] = {
> >> +static const struct iio_chan_spec at91_sama5d2_adc_channels[] = {
> >> AT91_SAMA5D2_CHAN_SINGLE(0, 0x50),
> >> AT91_SAMA5D2_CHAN_SINGLE(1, 0x54),
> >> AT91_SAMA5D2_CHAN_SINGLE(2, 0x58),
> >> @@ -461,6 +520,42 @@ static const struct iio_chan_spec at91_adc_channels[] = {
> >> AT91_SAMA5D2_CHAN_PRESSURE(AT91_SAMA5D2_TOUCH_P_CHAN_IDX, "pressure"),
> >> };
> >>
> >> +static const struct iio_chan_spec at91_sama7g5_adc_channels[] = {
> >> + AT91_SAMA5D2_CHAN_SINGLE(0, 0x60),
> >> + AT91_SAMA5D2_CHAN_SINGLE(1, 0x64),
> >> + AT91_SAMA5D2_CHAN_SINGLE(2, 0x68),
> >> + AT91_SAMA5D2_CHAN_SINGLE(3, 0x6c),
> >> + AT91_SAMA5D2_CHAN_SINGLE(4, 0x70),
> >> + AT91_SAMA5D2_CHAN_SINGLE(5, 0x74),
> >> + AT91_SAMA5D2_CHAN_SINGLE(6, 0x78),
> >> + AT91_SAMA5D2_CHAN_SINGLE(7, 0x7c),
> >> + AT91_SAMA5D2_CHAN_SINGLE(8, 0x80),
> >> + AT91_SAMA5D2_CHAN_SINGLE(9, 0x84),
> >> + AT91_SAMA5D2_CHAN_SINGLE(10, 0x88),
> >> + AT91_SAMA5D2_CHAN_SINGLE(11, 0x8c),
> >> + AT91_SAMA5D2_CHAN_SINGLE(12, 0x90),
> >> + AT91_SAMA5D2_CHAN_SINGLE(13, 0x94),
> >> + AT91_SAMA5D2_CHAN_SINGLE(14, 0x98),
> >> + AT91_SAMA5D2_CHAN_SINGLE(15, 0x9c),
> >> + AT91_SAMA7G5_CHAN_DIFF(0, 1, 0x60),
> >> + AT91_SAMA7G5_CHAN_DIFF(2, 3, 0x68),
> >> + AT91_SAMA7G5_CHAN_DIFF(4, 5, 0x70),
> >> + AT91_SAMA7G5_CHAN_DIFF(6, 7, 0x78),
> >> + AT91_SAMA7G5_CHAN_DIFF(8, 9, 0x80),
> >> + AT91_SAMA7G5_CHAN_DIFF(10, 11, 0x88),
> >> + AT91_SAMA7G5_CHAN_DIFF(12, 13, 0x90),
> >> + AT91_SAMA7G5_CHAN_DIFF(14, 15, 0x98),
> >> + IIO_CHAN_SOFT_TIMESTAMP(AT91_SAMA7G5_TIMESTAMP_CHAN_IDX),
> >> +};
> >> +
> >> +static unsigned int at91_adc_max_chan_idx(struct at91_adc_state *st)
> >> +{
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + return AT91_SAMA7G5_MAX_CHAN_IDX;
> >> + else
> >> + return AT91_SAMA5D2_MAX_CHAN_IDX;
> >> +}
> >> +
> >> static int at91_adc_chan_xlate(struct iio_dev *indio_dev, int chan)
> >> {
> >> int i;
> >> @@ -492,6 +587,7 @@ static unsigned int at91_adc_active_scan_mask_to_reg(struct iio_dev *indio_dev)
> >> {
> >> u32 mask = 0;
> >> u8 bit;
> >> + struct at91_adc_state *st = iio_priv(indio_dev);
> >>
> >> for_each_set_bit(bit, indio_dev->active_scan_mask,
> >> indio_dev->num_channels) {
> >> @@ -500,13 +596,78 @@ static unsigned int at91_adc_active_scan_mask_to_reg(struct iio_dev *indio_dev)
> >> mask |= BIT(chan->channel);
> >> }
> >>
> >> - return mask & GENMASK(11, 0);
> >> + return mask & GENMASK(at91_adc_max_chan_idx(st), 0);
> >> +}
> >> +
> >> +static void at91_adc_ccr(struct at91_adc_state *st,
> >> + struct iio_chan_spec const *chan)
> >> +{
> >> + u32 ccr, cur_ccr;
> >> +
> >> + ccr = (BIT(chan->channel) | BIT(chan->channel2));
> >> +
> >> + if (AT91_ADC_SAMA7G5(st)) {
> >> + cur_ccr = at91_adc_readl(st, AT91_SAMA7G5_CCR);
> >> + ccr <<= AT91_SAMA7G5_COR_DIFF_OFFSET;
> >> + if (chan->differential)
> >> + at91_adc_writel(st, AT91_SAMA7G5_CCR, cur_ccr | ccr);
> >> + else
> >> + at91_adc_writel(st, AT91_SAMA7G5_CCR, cur_ccr & ~ccr);
> >> + } else {
> >> + cur_ccr = at91_adc_readl(st, AT91_SAMA5D2_COR);
> >> + ccr <<= AT91_SAMA5D2_COR_DIFF_OFFSET;
> >> + if (chan->differential)
> >> + at91_adc_writel(st, AT91_SAMA5D2_COR, cur_ccr | ccr);
> >> + else
> >> + at91_adc_writel(st, AT91_SAMA5D2_COR, cur_ccr & ~ccr);
> >> + }
> >> +}
> >> +
> >> +static void at91_adc_irq_status(struct at91_adc_state *st, u32 *status,
> >> + u32 *eoc)
> >> +{
> >> + if (AT91_ADC_SAMA7G5(st)) {
> >> + *status = at91_adc_readl(st, AT91_SAMA5D2_ISR);
> >> + *eoc = at91_adc_readl(st, AT91_SAMA7G5_EOC_ISR);
> >> + } else {
> >> + *status = *eoc = at91_adc_readl(st, AT91_SAMA5D2_ISR);
> >> + }
> >> +}
> >> +
> >> +static void at91_adc_irq_mask(struct at91_adc_state *st, u32 *status, u32 *eoc)
> >> +{
> >> + if (AT91_ADC_SAMA7G5(st)) {
> >> + *status = at91_adc_readl(st, AT91_SAMA5D2_IMR);
> >> + *eoc = at91_adc_readl(st, AT91_SAMA7G5_EOC_IMR);
> >> + } else {
> >> + *status = *eoc = at91_adc_readl(st, AT91_SAMA5D2_IMR);
> >> + }
> >> +}
> >> +
> >> +static void at91_adc_eoc_dis(struct at91_adc_state *st, unsigned int channel)
> >> +{
> >> + if (!AT91_ADC_SAMA7G5(st))
> >> + at91_adc_writel(st, AT91_SAMA5D2_IDR, BIT(channel));
> >> + /* for SAMA7G5, Errata recommends not writing to EOC_IDR register */
> >> +}
> >> +
> >> +static void at91_adc_eoc_ena(struct at91_adc_state *st, unsigned int channel)
> >> +{
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + at91_adc_writel(st, AT91_SAMA7G5_EOC_IER, BIT(channel));
> >> + else
> >> + at91_adc_writel(st, AT91_SAMA5D2_IER, BIT(channel));
> >> }
> >>
> >> static void at91_adc_config_emr(struct at91_adc_state *st)
> >> {
> >> /* configure the extended mode register */
> >> - unsigned int emr = at91_adc_readl(st, AT91_SAMA5D2_EMR);
> >> + unsigned int emr;
> >> +
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + emr = at91_adc_readl(st, AT91_SAMA7G5_EMR);
> >> + else
> >> + emr = at91_adc_readl(st, AT91_SAMA5D2_EMR);
> >>
> >> /* select oversampling per single trigger event */
> >> emr |= AT91_SAMA5D2_EMR_ASTE(1);
> >> @@ -530,7 +691,10 @@ static void at91_adc_config_emr(struct at91_adc_state *st)
> >> break;
> >> }
> >>
> >> - at91_adc_writel(st, AT91_SAMA5D2_EMR, emr);
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + at91_adc_writel(st, AT91_SAMA7G5_EMR, emr);
> >> + else
> >> + at91_adc_writel(st, AT91_SAMA5D2_EMR, emr);
> >> }
> >>
> >> static int at91_adc_adjust_val_osr(struct at91_adc_state *st, int *val)
> >> @@ -726,7 +890,12 @@ static int at91_adc_configure_trigger(struct iio_trigger *trig, bool state)
> >> {
> >> struct iio_dev *indio = iio_trigger_get_drvdata(trig);
> >> struct at91_adc_state *st = iio_priv(indio);
> >> - u32 status = at91_adc_readl(st, AT91_SAMA5D2_TRGR);
> >> + u32 status;
> >> +
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + status = at91_adc_readl(st, AT91_SAMA7G5_TRGR);
> >> + else
> >> + status = at91_adc_readl(st, AT91_SAMA5D2_TRGR);
> >>
> >> /* clear TRGMOD */
> >> status &= ~AT91_SAMA5D2_TRGR_TRGMOD_MASK;
> >> @@ -735,7 +904,10 @@ static int at91_adc_configure_trigger(struct iio_trigger *trig, bool state)
> >> status |= st->selected_trig->trgmod_value;
> >>
> >> /* set/unset hw trigger */
> >> - at91_adc_writel(st, AT91_SAMA5D2_TRGR, status);
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + at91_adc_writel(st, AT91_SAMA7G5_TRGR, status);
> >> + else
> >> + at91_adc_writel(st, AT91_SAMA5D2_TRGR, status);
> >>
> >> return 0;
> >> }
> >> @@ -877,7 +1049,7 @@ static bool at91_adc_current_chan_is_touch(struct iio_dev *indio_dev)
> >>
> >> return !!bitmap_subset(indio_dev->active_scan_mask,
> >> &st->touch_st.channels_bitmask,
> >> - AT91_SAMA5D2_MAX_CHAN_IDX + 1);
> >> + at91_adc_max_chan_idx(st) + 1);
> >> }
> >>
> >> static int at91_adc_buffer_prepare(struct iio_dev *indio_dev)
> >> @@ -905,7 +1077,6 @@ static int at91_adc_buffer_prepare(struct iio_dev *indio_dev)
> >> indio_dev->num_channels) {
> >> struct iio_chan_spec const *chan =
> >> at91_adc_chan_get(indio_dev, bit);
> >> - u32 cor;
> >>
> >> if (!chan)
> >> continue;
> >> @@ -914,16 +1085,7 @@ static int at91_adc_buffer_prepare(struct iio_dev *indio_dev)
> >> chan->type == IIO_PRESSURE)
> >> continue;
> >>
> >> - cor = at91_adc_readl(st, AT91_SAMA5D2_COR);
> >> -
> >> - if (chan->differential)
> >> - cor |= (BIT(chan->channel) | BIT(chan->channel2)) <<
> >> - AT91_SAMA5D2_COR_DIFF_OFFSET;
> >> - else
> >> - cor &= ~(BIT(chan->channel) <<
> >> - AT91_SAMA5D2_COR_DIFF_OFFSET);
> >> -
> >> - at91_adc_writel(st, AT91_SAMA5D2_COR, cor);
> >> + at91_adc_ccr(st, chan);
> >>
> >> at91_adc_writel(st, AT91_SAMA5D2_CHER, BIT(chan->channel));
> >> }
> >> @@ -975,7 +1137,10 @@ static int at91_adc_buffer_postdisable(struct iio_dev *indio_dev)
> >> at91_adc_writel(st, AT91_SAMA5D2_IDR, AT91_SAMA5D2_IER_DRDY);
> >>
> >> /* read overflow register to clear possible overflow status */
> >> - at91_adc_readl(st, AT91_SAMA5D2_OVER);
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + at91_adc_readl(st, AT91_SAMA7G5_OVER);
> >> + else
> >> + at91_adc_readl(st, AT91_SAMA5D2_OVER);
> >>
> >> /* if we are using DMA we must clear registers and end DMA */
> >> if (st->dma_st.dma_chan)
> >> @@ -1018,13 +1183,15 @@ static void at91_adc_trigger_handler_nodma(struct iio_dev *indio_dev,
> >> u8 bit;
> >> u32 mask = at91_adc_active_scan_mask_to_reg(indio_dev);
> >> unsigned int timeout = 50;
> >> + u32 status, imr, eoc = 0, eoc_imr;
> >>
> >> /*
> >> * Check if the conversion is ready. If not, wait a little bit, and
> >> * in case of timeout exit with an error.
> >> */
> >> - while ((at91_adc_readl(st, AT91_SAMA5D2_ISR) & mask) != mask &&
> >> - timeout) {
> >> + while (((eoc & mask) != mask) && timeout) {
> >> + at91_adc_irq_status(st, &status, &eoc);
> >> + at91_adc_irq_mask(st, &imr, &eoc_imr);
> >> usleep_range(50, 100);
> >> timeout--;
> >> }
> >> @@ -1195,7 +1362,7 @@ static void at91_adc_touch_data_handler(struct iio_dev *indio_dev)
> >> int i = 0;
> >>
> >> for_each_set_bit(bit, indio_dev->active_scan_mask,
> >> - AT91_SAMA5D2_MAX_CHAN_IDX + 1) {
> >> + at91_adc_max_chan_idx(st) + 1) {
> >> struct iio_chan_spec const *chan =
> >> at91_adc_chan_get(indio_dev, bit);
> >>
> >> @@ -1262,12 +1429,14 @@ static irqreturn_t at91_adc_interrupt(int irq, void *private)
> >> {
> >> struct iio_dev *indio = private;
> >> struct at91_adc_state *st = iio_priv(indio);
> >> - u32 status = at91_adc_readl(st, AT91_SAMA5D2_ISR);
> >> - u32 imr = at91_adc_readl(st, AT91_SAMA5D2_IMR);
> >> + u32 status, eoc, imr, eoc_imr;
> >> u32 rdy_mask = AT91_SAMA5D2_IER_XRDY | AT91_SAMA5D2_IER_YRDY |
> >> AT91_SAMA5D2_IER_PRDY;
> >>
> >> - if (!(status & imr))
> >> + at91_adc_irq_status(st, &status, &eoc);
> >> + at91_adc_irq_mask(st, &imr, &eoc_imr);
> >> +
> >> + if (!(status & imr) && !(eoc & eoc_imr))
> >> return IRQ_NONE;
> >> if (status & AT91_SAMA5D2_IER_PEN) {
> >> /* pen detected IRQ */
> >> @@ -1309,7 +1478,6 @@ static int at91_adc_read_info_raw(struct iio_dev *indio_dev,
> >> struct iio_chan_spec const *chan, int *val)
> >> {
> >> struct at91_adc_state *st = iio_priv(indio_dev);
> >> - u32 cor = 0;
> >> u16 tmp_val;
> >> int ret;
> >>
> >> @@ -1355,13 +1523,9 @@ static int at91_adc_read_info_raw(struct iio_dev *indio_dev,
> >>
> >> st->chan = chan;
> >>
> >> - if (chan->differential)
> >> - cor = (BIT(chan->channel) | BIT(chan->channel2)) <<
> >> - AT91_SAMA5D2_COR_DIFF_OFFSET;
> >> -
> >> - at91_adc_writel(st, AT91_SAMA5D2_COR, cor);
> >> + at91_adc_ccr(st, chan);
> >> at91_adc_writel(st, AT91_SAMA5D2_CHER, BIT(chan->channel));
> >> - at91_adc_writel(st, AT91_SAMA5D2_IER, BIT(chan->channel));
> >> + at91_adc_eoc_ena(st, chan->channel);
> >> at91_adc_writel(st, AT91_SAMA5D2_CR, AT91_SAMA5D2_CR_START);
> >>
> >> ret = wait_event_interruptible_timeout(st->wq_data_available,
> >> @@ -1378,7 +1542,7 @@ static int at91_adc_read_info_raw(struct iio_dev *indio_dev,
> >> st->conversion_done = false;
> >> }
> >>
> >> - at91_adc_writel(st, AT91_SAMA5D2_IDR, BIT(chan->channel));
> >> + at91_adc_eoc_dis(st, st->chan->channel);
> >> at91_adc_writel(st, AT91_SAMA5D2_CHDR, BIT(chan->channel));
> >>
> >> /* Needed to ACK the DRDY interruption */
> >> @@ -1577,14 +1741,14 @@ static int at91_adc_update_scan_mode(struct iio_dev *indio_dev,
> >> struct at91_adc_state *st = iio_priv(indio_dev);
> >>
> >> if (bitmap_subset(scan_mask, &st->touch_st.channels_bitmask,
> >> - AT91_SAMA5D2_MAX_CHAN_IDX + 1))
> >> + at91_adc_max_chan_idx(st) + 1))
> >> return 0;
> >> /*
> >> * if the new bitmap is a combination of touchscreen and regular
> >> * channels, then we are not fine
> >> */
> >> if (bitmap_intersects(&st->touch_st.channels_bitmask, scan_mask,
> >> - AT91_SAMA5D2_MAX_CHAN_IDX + 1))
> >> + at91_adc_max_chan_idx(st) + 1))
> >> return -EINVAL;
> >> return 0;
> >> }
> >> @@ -1594,6 +1758,8 @@ static void at91_adc_hw_init(struct iio_dev *indio_dev)
> >> struct at91_adc_state *st = iio_priv(indio_dev);
> >>
> >> at91_adc_writel(st, AT91_SAMA5D2_CR, AT91_SAMA5D2_CR_SWRST);
> >> + if (AT91_ADC_SAMA7G5(st))
> >> + at91_adc_writel(st, AT91_SAMA7G5_EOC_IDR, 0xffffffff);
> >> at91_adc_writel(st, AT91_SAMA5D2_IDR, 0xffffffff);
> >> /*
> >> * Transfer field must be set to 2 according to the datasheet and
> >> @@ -1718,18 +1884,27 @@ static int at91_adc_probe(struct platform_device *pdev)
> >> indio_dev->name = dev_name(&pdev->dev);
> >> indio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
> >> indio_dev->info = &at91_adc_info;
> >> - indio_dev->channels = at91_adc_channels;
> >> - indio_dev->num_channels = ARRAY_SIZE(at91_adc_channels);
> >>
> >> st = iio_priv(indio_dev);
> >> st->indio_dev = indio_dev;
> >>
> >> - bitmap_set(&st->touch_st.channels_bitmask,
> >> - AT91_SAMA5D2_TOUCH_X_CHAN_IDX, 1);
> >> - bitmap_set(&st->touch_st.channels_bitmask,
> >> - AT91_SAMA5D2_TOUCH_Y_CHAN_IDX, 1);
> >> - bitmap_set(&st->touch_st.channels_bitmask,
> >> - AT91_SAMA5D2_TOUCH_P_CHAN_IDX, 1);
> >> + st->soc_info.sama7g5 = of_device_is_compatible(pdev->dev.of_node,
> >> + "microchip,sama7g5-adc");
> >
> > Better to use match_data to get an enum value which is used to index
> > into a table of support part description structures. Each of those
> > structures has all the registers etc + channel specs and callbacks
> > where needed for more complex handling.
> >
> > Other advantage is you can introduce the structures in a precursor patch with
> > just one entry for existing behaviour. The new device support is then added
> > in a second patch. All we need to do then is check first patch is a noop
> > and that second much shorter patch makes sense.
> >
> >> +
> >> + if (AT91_ADC_SAMA7G5(st)) {
> >> + indio_dev->channels = at91_sama7g5_adc_channels;
> >> + indio_dev->num_channels = ARRAY_SIZE(at91_sama7g5_adc_channels);
> >> + } else {
> >> + indio_dev->channels = at91_sama5d2_adc_channels;
> >> + indio_dev->num_channels = ARRAY_SIZE(at91_sama5d2_adc_channels);
> >> +
> >> + bitmap_set(&st->touch_st.channels_bitmask,
> >> + AT91_SAMA5D2_TOUCH_X_CHAN_IDX, 1);
> >> + bitmap_set(&st->touch_st.channels_bitmask,
> >> + AT91_SAMA5D2_TOUCH_Y_CHAN_IDX, 1);
> >> + bitmap_set(&st->touch_st.channels_bitmask,
> >> + AT91_SAMA5D2_TOUCH_P_CHAN_IDX, 1);
> >> + }
> >>
> >> st->oversampling_ratio = AT91_OSR_1SAMPLES;
> >>
> >> @@ -1853,9 +2028,12 @@ static int at91_adc_probe(struct platform_device *pdev)
> >> dev_info(&pdev->dev, "setting up trigger as %s\n",
> >> st->selected_trig->name);
> >>
> >> - dev_info(&pdev->dev, "version: %x\n",
> >> - readl_relaxed(st->base + AT91_SAMA5D2_VERSION));
> >> -
> >> + if (AT91_ADC_SAMA7G5(st))
> >
> > We may be better off with a look up table of all the registers
> > (+ if needed some callback functions) rather than a whole bunch of
> > if statements.
> >
> > You then just assign the right 'part number specific' structure
> > once in probe.
> >
> >> + dev_info(&pdev->dev, "version: %x\n",
> >> + at91_adc_readl(st, AT91_SAMA7G5_VERSION));
> >> + else
> >> + dev_info(&pdev->dev, "version: %x\n",
> >> + at91_adc_readl(st, AT91_SAMA5D2_VERSION));
> >> return 0;
> >>
> >> dma_disable:
> >> @@ -1957,6 +2135,8 @@ static SIMPLE_DEV_PM_OPS(at91_adc_pm_ops, at91_adc_suspend, at91_adc_resume);
> >> static const struct of_device_id at91_adc_dt_match[] = {
> >> {
> >> .compatible = "atmel,sama5d2-adc",
> >> + }, {
> >> + .compatible = "microchip,sama7g5-adc",
> >> }, {
> >> /* sentinel */
> >> }
> >> @@ -1967,13 +2147,14 @@ static struct platform_driver at91_adc_driver = {
> >> .probe = at91_adc_probe,
> >> .remove = at91_adc_remove,
> >> .driver = {
> >> - .name = "at91-sama5d2_adc",
> >> + .name = "at91-sama5d2-sama7g5_adc",
> >
> > Please keep the driver name the same. It's common to have a name of one
> > random part a driver supports used even if there are lots of others.
> > This (or wild cards) never scales as more parts are added to a driver.
> >
> >> .of_match_table = at91_adc_dt_match,
> >> .pm = &at91_adc_pm_ops,
> >> },
> >> };
> >> module_platform_driver(at91_adc_driver)
> >>
> >> -MODULE_AUTHOR("Ludovic Desroches <ludovic.desroches@...el.com>");
> >> -MODULE_DESCRIPTION("Atmel AT91 SAMA5D2 ADC");
> >> +MODULE_AUTHOR("Ludovic Desroches <ludovic.desroches@...rochip.com>");
> >> +MODULE_AUTHOR("Eugen Hristev <eugen.hristev@...rochip.com>");
> >> +MODULE_DESCRIPTION("Microchip AT91 SAMA5D2/SAMA7G5 ADC");
> >> MODULE_LICENSE("GPL v2");
> >
>
Powered by blists - more mailing lists