| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210311033957.8978-1-rojay@codeaurora.org>
Date: Thu, 11 Mar 2021 09:09:57 +0530
From: Roja Rani Yarubandi <rojay@...eaurora.org>
To: agross@...nel.org, bjorn.andersson@...aro.org, robh+dt@...nel.org
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Rajendra Nayak <rnayak@...eaurora.org>,
akashast@...eaurora.org, msavaliy@....qualcomm.com,
Roja Rani Yarubandi <rojay@...eaurora.org>
Subject: [PATCH] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes
Add QSPI and QUP SE instances configuration for sc7280.
Signed-off-by: Roja Rani Yarubandi <rojay@...eaurora.org>
---
This patch depends on base dtsi and interconnect changes
[1] https://lore.kernel.org/patchwork/project/lkml/list/?series=487403
[2] https://lore.kernel.org/patchwork/project/lkml/list/?series=488429
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 140 ++-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 1296 ++++++++++++++++++++++-
2 files changed, 1430 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 950ecb25f281..e152d5a51c6b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -15,6 +15,7 @@ / {
aliases {
serial0 = &uart5;
+ hsuart0 = &uart7;
};
chosen {
@@ -22,26 +23,157 @@ chosen {
};
};
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /* TODO: Increase frequency after testing */
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&uart5 {
status = "okay";
};
+&uart7 {
+ status = "okay";
+
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+&qspi_cs0 {
+ pinconf {
+ pins = "gpio15";
+ bias-disable;
+ };
+};
+
+&qspi_clk {
+ pinconf {
+ pins = "gpio14";
+ bias-disable;
+ };
+};
+
+&qspi_data01 {
+ pinconf {
+ pins = "gpio12", "gpio13";
+
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+ };
+};
+
&qup_uart5_default {
- tx {
- pins = "gpio46";
+ pinconf-tx {
+ pins = "gpio22";
drive-strength = <2>;
bias-disable;
};
- rx {
- pins = "gpio47";
+ pinconf-rx {
+ pins = "gpio23";
drive-strength = <2>;
bias-pull-up;
};
};
+
+&qup_uart7_default {
+ pinconf-cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ pins = "gpio28";
+ bias-pull-down;
+ };
+
+ pinconf-rts-tx {
+ /* We'll drive RTS and TX, so no pull */
+ pins = "gpio29", "gpio30";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ pins = "gpio31";
+ bias-pull-up;
+ };
+};
+
+&tlmm {
+ qup_uart7_sleep: qup-uart7-sleep {
+ pinmux {
+ pins = "gpio28", "gpio29",
+ "gpio30", "gpio31";
+ function = "gpio";
+ };
+
+ pinconf-cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ pins = "gpio28";
+ bias-pull-down;
+ };
+
+ pinconf-rts {
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ pins = "gpio29";
+ bias-pull-down;
+ };
+
+ pinconf-tx {
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ pins = "gpio30";
+ bias-pull-up;
+ };
+
+ pinconf-rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ pins = "gpio31";
+ bias-pull-up;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index ecb2a77a1a6a..e6cafe568358 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -283,6 +283,25 @@ gcc: clock-controller@...000 {
#power-domain-cells = <1>;
};
+ qup_opp_table: qup-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-128000000 {
+ opp-hz = /bits/ 64 <128000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
qupv3_id_0: geniqup@...000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
@@ -292,8 +311,307 @@ qupv3_id_0: geniqup@...000 {
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ iommus = <&apps_smmu 0x123 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+ interconnect-names = "qup-core";
status = "disabled";
+ i2c0: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi0: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart0: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c1: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi1: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart1: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c2: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi2: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart2: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c3: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi3: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart3: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c4: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi4: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart4: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c5: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi5: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
uart5: serial@...000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x00994000 0 0x4000>;
@@ -302,6 +620,546 @@ uart5: serial@...000 {
pinctrl-names = "default";
pinctrl-0 = <&qup_uart5_default>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c6: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_default>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi6: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_default>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart6: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_default>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c7: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_default>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi7: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi7_default>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart7: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_default>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
+ qupv3_id_1: geniqup@...000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x2000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x43 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+ interconnect-names = "qup-core";
+ status = "disabled";
+
+ i2c8: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi8: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart8: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c9: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi9: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart9: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart9_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c10: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi10: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart10: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c11: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi11: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart11: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c12: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi12: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart12: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart12_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c13: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi13: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart13: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c14: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_default>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi14: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_default>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart14: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart14_default>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c15: i2c@...000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_default>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi15: spi@...000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_default>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart15: serial@...000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart15_default>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
status = "disabled";
};
};
@@ -349,9 +1207,407 @@ tlmm: pinctrl@...0000 {
gpio-ranges = <&tlmm 0 0 175>;
wakeup-parent = <&pdc>;
+ qspi_clk: qspi-clk {
+ pinmux {
+ pins = "gpio14";
+ function = "qspi_clk";
+ };
+ };
+
+ qspi_cs0: qspi-cs0 {
+ pinmux {
+ pins = "gpio15";
+ function = "qspi_cs";
+ };
+ };
+
+ qspi_cs1: qspi-cs1 {
+ pinmux {
+ pins = "gpio19";
+ function = "qspi_cs";
+ };
+ };
+
+ qspi_data01: qspi-data01 {
+ pinmux-data {
+ pins = "gpio12", "gpio13";
+ function = "qspi_data";
+ };
+ };
+
+ qspi_data12: qspi-data12 {
+ pinmux-data {
+ pins = "gpio16", "gpio17";
+ function = "qspi_data";
+ };
+ };
+
+ qup_i2c0_default: qup-i2c0-default {
+ pinmux {
+ pins = "gpio0", "gpio1";
+ function = "qup00";
+ };
+ };
+
+ qup_i2c1_default: qup-i2c1-default {
+ pinmux {
+ pins = "gpio4", "gpio5";
+ function = "qup01";
+ };
+ };
+
+ qup_i2c2_default: qup-i2c2-default {
+ pinmux {
+ pins = "gpio8", "gpio9";
+ function = "qup02";
+ };
+ };
+
+ qup_i2c3_default: qup-i2c3-default {
+ pinmux {
+ pins = "gpio12", "gpio13";
+ function = "qup03";
+ };
+ };
+
+ qup_i2c4_default: qup-i2c4-default {
+ pinmux {
+ pins = "gpio16", "gpio17";
+ function = "qup04";
+ };
+ };
+
+ qup_i2c5_default: qup-i2c5-default {
+ pinmux {
+ pins = "gpio20", "gpio21";
+ function = "qup05";
+ };
+ };
+
+ qup_i2c6_default: qup-i2c6-default {
+ pinmux {
+ pins = "gpio24", "gpio25";
+ function = "qup06";
+ };
+ };
+
+ qup_i2c7_default: qup-i2c7-default {
+ pinmux {
+ pins = "gpio28", "gpio29";
+ function = "qup07";
+ };
+ };
+
+ qup_i2c8_default: qup-i2c8-default {
+ pinmux {
+ pins = "gpio32", "gpio33";
+ function = "qup10";
+ };
+ };
+
+ qup_i2c9_default: qup-i2c9-default {
+ pinmux {
+ pins = "gpio36", "gpio37";
+ function = "qup11";
+ };
+ };
+
+ qup_i2c10_default: qup-i2c10-default {
+ pinmux {
+ pins = "gpio40", "gpio41";
+ function = "qup12";
+ };
+ };
+
+ qup_i2c11_default: qup-i2c11-default {
+ pinmux {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ };
+ };
+
+ qup_i2c12_default: qup-i2c12-default {
+ pinmux {
+ pins = "gpio48", "gpio49";
+ function = "qup14";
+ };
+ };
+
+ qup_i2c13_default: qup-i2c13-default {
+ pinmux {
+ pins = "gpio52", "gpio53";
+ function = "qup15";
+ };
+ };
+
+ qup_i2c14_default: qup-i2c14-default {
+ pinmux {
+ pins = "gpio56", "gpio57";
+ function = "qup16";
+ };
+ };
+
+ qup_i2c15_default: qup-i2c15-default {
+ pinmux {
+ pins = "gpio60", "gpio61";
+ function = "qup17";
+ };
+ };
+
+ qup_spi0_default: qup-spi0-default {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "qup00";
+ };
+ };
+
+ qup_spi1_default: qup-spi1-default {
+ pinmux {
+ pins = "gpio4", "gpio5",
+ "gpio6", "gpio7";
+ function = "qup01";
+ };
+ };
+
+ qup_spi2_default: qup-spi2-default {
+ pinmux {
+ pins = "gpio8", "gpio9",
+ "gpio10", "gpio11";
+ function = "qup02";
+ };
+ };
+
+ qup_spi3_default: qup-spi3-default {
+ pinmux {
+ pins = "gpio12", "gpio13",
+ "gpio14", "gpio15";
+ function = "qup03";
+ };
+ };
+
+ qup_spi4_default: qup-spi4-default {
+ pinmux {
+ pins = "gpio16", "gpio17",
+ "gpio18", "gpio19";
+ function = "qup04";
+ };
+ };
+
+ qup_spi5_default: qup-spi5-default {
+ pinmux {
+ pins = "gpio20", "gpio21",
+ "gpio22", "gpio23";
+ function = "qup05";
+ };
+ };
+
+ qup_spi6_default: qup-spi6-default {
+ pinmux {
+ pins = "gpio24", "gpio25",
+ "gpio26", "gpio27";
+ function = "qup06";
+ };
+ };
+
+ qup_spi7_default: qup-spi7-default {
+ pinmux {
+ pins = "gpio28", "gpio29",
+ "gpio30", "gpio31";
+ function = "qup07";
+ };
+ };
+
+ qup_spi8_default: qup-spi8-default {
+ pinmux {
+ pins = "gpio32", "gpio33",
+ "gpio34", "gpio35";
+ function = "qup10";
+ };
+ };
+
+ qup_spi9_default: qup-spi9-default {
+ pinmux {
+ pins = "gpio36", "gpio37",
+ "gpio38", "gpio39";
+ function = "qup11";
+ };
+ };
+
+ qup_spi10_default: qup-spi10-default {
+ pinmux {
+ pins = "gpio40", "gpio41",
+ "gpio42", "gpio43";
+ function = "qup12";
+ };
+ };
+
+ qup_spi11_default: qup-spi11-default {
+ pinmux {
+ pins = "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "qup13";
+ };
+ };
+
+ qup_spi12_default: qup-spi12-default {
+ pinmux {
+ pins = "gpio48", "gpio49",
+ "gpio50", "gpio51";
+ function = "qup14";
+ };
+ };
+
+ qup_spi13_default: qup-spi13-default {
+ pinmux {
+ pins = "gpio52", "gpio53",
+ "gpio54", "gpio55";
+ function = "qup15";
+ };
+ };
+
+ qup_spi14_default: qup-spi14-default {
+ pinmux {
+ pins = "gpio56", "gpio57",
+ "gpio58", "gpio59";
+ function = "qup16";
+ };
+ };
+
+ qup_spi15_default: qup-spi15-default {
+ pinmux {
+ pins = "gpio60", "gpio61",
+ "gpio62", "gpio63";
+ function = "qup17";
+ };
+ };
+
+ qup_uart0_default: qup-uart0-default {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "qup00";
+ };
+ };
+
+ qup_uart1_default: qup-uart1-default {
+ pinmux {
+ pins = "gpio4", "gpio5",
+ "gpio6", "gpio7";
+ function = "qup01";
+ };
+ };
+
+ qup_uart2_default: qup-uart2-default {
+ pinmux {
+ pins = "gpio8", "gpio9",
+ "gpio10", "gpio11";
+ function = "qup02";
+ };
+ };
+
+ qup_uart3_default: qup-uart3-default {
+ pinmux {
+ pins = "gpio12", "gpio13",
+ "gpio14", "gpio15";
+ function = "qup03";
+ };
+ };
+
+ qup_uart4_default: qup-uart4-default {
+ pinmux {
+ pins = "gpio16", "gpio17",
+ "gpio18", "gpio19";
+ function = "qup04";
+ };
+ };
+
qup_uart5_default: qup-uart5-default {
- pins = "gpio46", "gpio47";
- function = "qup13";
+ pinmux {
+ pins = "gpio20", "gpio21",
+ "gpio22", "gpio23";
+ function = "qup05";
+ };
+ };
+
+ qup_uart6_default: qup-uart6-default {
+ pinmux {
+ pins = "gpio24", "gpio25",
+ "gpio26", "gpio27";
+ function = "qup06";
+ };
+ };
+
+ qup_uart7_default: qup-uart7-default {
+ pinmux {
+ pins = "gpio28", "gpio29",
+ "gpio30", "gpio31";
+ function = "qup07";
+ };
+ };
+
+ qup_uart8_default: qup-uart8-default {
+ pinmux {
+ pins = "gpio32", "gpio33",
+ "gpio34", "gpio35";
+ function = "qup10";
+ };
+ };
+
+ qup_uart9_default: qup-uart9-default {
+ pinmux {
+ pins = "gpio36", "gpio37",
+ "gpio38", "gpio39";
+ function = "qup11";
+ };
+ };
+
+ qup_uart10_default: qup-uart10-default {
+ pinmux {
+ pins = "gpio40", "gpio41",
+ "gpio42", "gpio43";
+ function = "qup12";
+ };
+ };
+
+ qup_uart11_default: qup-uart11-default {
+ pinmux {
+ pins = "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "qup13";
+ };
+ };
+
+ qup_uart12_default: qup-uart12-default {
+ pinmux {
+ pins = "gpio48", "gpio49",
+ "gpio50", "gpio51";
+ function = "qup14";
+ };
+ };
+
+ qup_uart13_default: qup-uart13-default {
+ pinmux {
+ pins = "gpio52", "gpio53",
+ "gpio54", "gpio55";
+ function = "qup15";
+ };
+ };
+
+ qup_uart14_default: qup-uart14-default {
+ pinmux {
+ pins = "gpio56", "gpio57",
+ "gpio58", "gpio59";
+ function = "qup16";
+ };
+ };
+
+ qup_uart15_default: qup-uart15-default {
+ pinmux {
+ pins = "gpio60", "gpio61",
+ "gpio62", "gpio63";
+ function = "qup17";
+ };
};
};
@@ -444,6 +1700,42 @@ apps_smmu: iommu@...00000 {
<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
};
+ qspi_opp_table: qspi-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-150000000 {
+ opp-hz = /bits/ 64 <150000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
+ qspi: spi@...c000 {
+ compatible = "qcom,qspi-v1";
+ reg = <0 0x088dc000 0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+ clock-names = "iface", "core";
+ interconnects = <&gem_noc MASTER_APPSS_PROC 0
+ &cnoc2 SLAVE_QSPI_0 0>;
+ interconnect-names = "qspi-config";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qspi_opp_table>;
+ status = "disabled";
+ };
+
intc: interrupt-controller@...00000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Powered by blists - more mailing lists