| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210315131512.133720-18-jacopo+renesas@jmondi.org>
Date: Mon, 15 Mar 2021 14:15:11 +0100
From: Jacopo Mondi <jacopo+renesas@...ndi.org>
To: kieran.bingham+renesas@...asonboard.com,
laurent.pinchart+renesas@...asonboard.com,
niklas.soderlund+renesas@...natech.se, geert@...ux-m68k.org
Cc: Jacopo Mondi <jacopo+renesas@...ndi.org>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
linux-media@...r.kernel.org, linux-renesas-soc@...r.kernel.org,
linux-kernel@...r.kernel.org,
Laurent Pinchart <laurent.pinchart@...asonboard.com>
Subject: [PATCH v2 17/18] media: gmsl: Reimplement initialization sequence
The current probe() procedure of the RDACM20 and RDACM20 GMSL cameras is
performed with the embedded MAX9271 serializer's noise immunity
threshold disabled. Once the camera has been initialized by probing the
embedded chips, the threshold is enabled and then compensated on the
deserializer's side by increasing the reverse channel signal amplitude
once all cameras have bound.
The probe routine is thus run without noise immunity activated which
in noisy environment conditions makes the probe sequence less reliable as
the chips configuration requires a relatively high amount of i2c
transactions.
Break chip initialization in two:
- At probe time only configure the serializer's reverse channel with
noise immunity activated, to reduce the number of transactions
performed without noise immunity protection enabled
- Move the chips initialization to the .init() core subdev operation
called by the deserializer after all camera have probed and
have increased their noise immunity threshold
The initialization routine looks like the following:
MAX9286 RDACM20/21
probe()
|
---------------------> |
probe() {
enable_threshold()
}
|<--------------------|
v4l2 async bound {
compensate_amplitude()
call subdev init()
|-------------------->|
init() {
access camera registers()
}
|<-------------------
}
Reviewed-by: Laurent Pinchart <laurent.pinchart@...asonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@...asonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@...ndi.org>
---
drivers/media/i2c/max9286.c | 19 ++++++++---
drivers/media/i2c/rdacm20.c | 63 ++++++++++++++++++++++---------------
drivers/media/i2c/rdacm21.c | 63 ++++++++++++++++++++++---------------
3 files changed, 91 insertions(+), 54 deletions(-)
diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
index 9124d5fa6ea3..b6347639901e 100644
--- a/drivers/media/i2c/max9286.c
+++ b/drivers/media/i2c/max9286.c
@@ -563,17 +563,28 @@ static int max9286_notify_bound(struct v4l2_async_notifier *notifier,
if (priv->bound_sources != priv->source_mask)
return 0;
+ /*
+ * Initialize all the remote camera. Increase the channel amplitude
+ * to compensate for the remote noise immunity threshold.
+ */
+ max9286_reverse_channel_setup(priv, MAX9286_REV_AMP_HIGH);
+ for_each_source(priv, source) {
+ ret = v4l2_subdev_call(source->sd, core, init, 0);
+ if (ret) {
+ dev_err(&priv->client->dev,
+ "Failed to initialize camera device %u\n",
+ index);
+ return ret;
+ }
+ }
+
/*
* All enabled sources have probed and enabled their reverse control
* channels:
- *
- * - Increase the reverse channel amplitude to compensate for the
- * remote ends high threshold
* - Verify all configuration links are properly detected
* - Disable auto-ack as communication on the control channel are now
* stable.
*/
- max9286_reverse_channel_setup(priv, MAX9286_REV_AMP_HIGH);
max9286_check_config_link(priv, priv->source_mask);
/*
diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c
index 2265ef7c65d4..57bf4d362cad 100644
--- a/drivers/media/i2c/rdacm20.c
+++ b/drivers/media/i2c/rdacm20.c
@@ -437,35 +437,12 @@ static int rdacm20_get_fmt(struct v4l2_subdev *sd,
return 0;
}
-static const struct v4l2_subdev_video_ops rdacm20_video_ops = {
- .s_stream = rdacm20_s_stream,
-};
-
-static const struct v4l2_subdev_pad_ops rdacm20_subdev_pad_ops = {
- .enum_mbus_code = rdacm20_enum_mbus_code,
- .get_fmt = rdacm20_get_fmt,
- .set_fmt = rdacm20_get_fmt,
-};
-
-static const struct v4l2_subdev_ops rdacm20_subdev_ops = {
- .video = &rdacm20_video_ops,
- .pad = &rdacm20_subdev_pad_ops,
-};
-
-static int rdacm20_initialize(struct rdacm20_device *dev)
+static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val)
{
+ struct rdacm20_device *dev = sd_to_rdacm20(sd);
unsigned int i;
int ret;
- /* Verify communication with the MAX9271: ping to wakeup. */
- dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
- max9271_wake_up(&dev->serializer);
-
- /* Serial link disabled during config as it needs a valid pixel clock. */
- ret = max9271_set_serial_link(&dev->serializer, false);
- if (ret)
- return ret;
-
/*
* Ensure that we have a good link configuration before attempting to
* identify the device.
@@ -548,6 +525,42 @@ static int rdacm20_initialize(struct rdacm20_device *dev)
dev_info(dev->dev, "Identified RDACM20 camera module\n");
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops rdacm20_core_ops = {
+ .init = rdacm20_init,
+};
+
+static const struct v4l2_subdev_video_ops rdacm20_video_ops = {
+ .s_stream = rdacm20_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops rdacm20_subdev_pad_ops = {
+ .enum_mbus_code = rdacm20_enum_mbus_code,
+ .get_fmt = rdacm20_get_fmt,
+ .set_fmt = rdacm20_get_fmt,
+};
+
+static const struct v4l2_subdev_ops rdacm20_subdev_ops = {
+ .core = &rdacm20_core_ops,
+ .video = &rdacm20_video_ops,
+ .pad = &rdacm20_subdev_pad_ops,
+};
+
+static int rdacm20_initialize(struct rdacm20_device *dev)
+{
+ int ret;
+
+ /* Verify communication with the MAX9271: ping to wakeup. */
+ dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
+ max9271_wake_up(&dev->serializer);
+
+ /* Serial link disabled during config as it needs a valid pixel clock. */
+ ret = max9271_set_serial_link(&dev->serializer, false);
+ if (ret)
+ return ret;
+
/*
* Set reverse channel high threshold to increase noise immunity.
*
diff --git a/drivers/media/i2c/rdacm21.c b/drivers/media/i2c/rdacm21.c
index 07cf077d8efd..0fc339d43d98 100644
--- a/drivers/media/i2c/rdacm21.c
+++ b/drivers/media/i2c/rdacm21.c
@@ -314,21 +314,6 @@ static int rdacm21_get_fmt(struct v4l2_subdev *sd,
return 0;
}
-static const struct v4l2_subdev_video_ops rdacm21_video_ops = {
- .s_stream = rdacm21_s_stream,
-};
-
-static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = {
- .enum_mbus_code = rdacm21_enum_mbus_code,
- .get_fmt = rdacm21_get_fmt,
- .set_fmt = rdacm21_get_fmt,
-};
-
-static const struct v4l2_subdev_ops rdacm21_subdev_ops = {
- .video = &rdacm21_video_ops,
- .pad = &rdacm21_subdev_pad_ops,
-};
-
static int ov10640_initialize(struct rdacm21_device *dev)
{
u8 val;
@@ -448,19 +433,11 @@ static int ov490_initialize(struct rdacm21_device *dev)
return 0;
}
-static int rdacm21_initialize(struct rdacm21_device *dev)
+static int rdacm21_init(struct v4l2_subdev *sd, unsigned int val)
{
+ struct rdacm21_device *dev = sd_to_rdacm21(sd);
int ret;
- /* Verify communication with the MAX9271: ping to wakeup. */
- dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
- max9271_wake_up(&dev->serializer);
-
- /* Enable reverse channel and disable the serial link. */
- ret = max9271_set_serial_link(&dev->serializer, false);
- if (ret)
- return ret;
-
/* Configure I2C bus at 105Kbps speed and configure GMSL. */
ret = max9271_configure_i2c(&dev->serializer,
MAX9271_I2CSLVSH_469NS_234NS |
@@ -507,6 +484,42 @@ static int rdacm21_initialize(struct rdacm21_device *dev)
if (ret)
return ret;
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops rdacm21_core_ops = {
+ .init = rdacm21_init,
+};
+
+static const struct v4l2_subdev_video_ops rdacm21_video_ops = {
+ .s_stream = rdacm21_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = {
+ .enum_mbus_code = rdacm21_enum_mbus_code,
+ .get_fmt = rdacm21_get_fmt,
+ .set_fmt = rdacm21_get_fmt,
+};
+
+static const struct v4l2_subdev_ops rdacm21_subdev_ops = {
+ .core = &rdacm21_core_ops,
+ .video = &rdacm21_video_ops,
+ .pad = &rdacm21_subdev_pad_ops,
+};
+
+static int rdacm21_initialize(struct rdacm21_device *dev)
+{
+ int ret;
+
+ /* Verify communication with the MAX9271: ping to wakeup. */
+ dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
+ max9271_wake_up(&dev->serializer);
+
+ /* Enable reverse channel and disable the serial link. */
+ ret = max9271_set_serial_link(&dev->serializer, false);
+ if (ret)
+ return ret;
+
/*
* Set reverse channel high threshold to increase noise immunity.
*
--
2.30.0
Powered by blists - more mailing lists