| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210316203036.17674-3-chris.packham@alliedtelesis.co.nz>
Date: Wed, 17 Mar 2021 09:30:36 +1300
From: Chris Packham <chris.packham@...iedtelesis.co.nz>
To: robh+dt@...nel.org, jdelvare@...e.com, linux@...ck-us.net
Cc: devicetree@...r.kernel.org, linux-hwmon@...r.kernel.org,
linux-kernel@...r.kernel.org,
Chris Packham <chris.packham@...iedtelesis.co.nz>
Subject: [PATCH v2 3/3] hwmon: (pmbus): Add driver for BluTek BPA-RS600
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@...iedtelesis.co.nz>
---
Notes:
Changes in v2:
- Whitespace and line length cleanup
- Add comments about commands that return data but shouldn't be used
Documentation/hwmon/bpa-rs600.rst | 74 +++++++++++++
drivers/hwmon/pmbus/Kconfig | 9 ++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/bpa-rs600.c | 172 ++++++++++++++++++++++++++++++
4 files changed, 256 insertions(+)
create mode 100644 Documentation/hwmon/bpa-rs600.rst
create mode 100644 drivers/hwmon/pmbus/bpa-rs600.c
diff --git a/Documentation/hwmon/bpa-rs600.rst b/Documentation/hwmon/bpa-rs600.rst
new file mode 100644
index 000000000000..28313995d4ae
--- /dev/null
+++ b/Documentation/hwmon/bpa-rs600.rst
@@ -0,0 +1,74 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver bpa-rs600
+=======================
+
+Supported chips:
+
+ * BPA-RS600-120
+
+ Datasheet: Publicly available at the BluTek website
+ http://blutekpower.com/wp-content/uploads/2019/01/BPA-RS600-120-07-19-2018.pdf
+
+Authors:
+ - Chris Packham <chris.packham@...iedtelesis.co.nz>
+
+Description
+-----------
+
+The BPA-RS600 is a compact 600W removable power supply module.
+
+Usage Notes
+-----------
+
+This driver does not probe for PMBus devices. You will have to instantiate
+devices explicitly.
+
+Sysfs attributes
+----------------
+
+======================= ============================================
+curr1_label "iin"
+curr1_input Measured input current
+curr1_max Maximum input current
+curr1_max_alarm Input current high alarm
+
+curr2_label "iout1"
+curr2_input Measured output current
+curr2_max Maximum output current
+curr2_max_alarm Output current high alarm
+
+fan1_input Measured fan speed
+fan1_alarm Fan warning
+fan1_fault Fan fault
+
+in1_label "vin"
+in1_input Measured input voltage
+in1_max Maximum input voltage
+in1_max_alarm Input voltage high alarm
+in1_min Minimum input voltage
+in1_min_alarm Input voltage low alarm
+
+in2_label "vout1"
+in2_input Measured output voltage
+in2_max Maximum output voltage
+in2_max_alarm Output voltage high alarm
+in2_min Maximum output voltage
+in2_min_alarm Output voltage low alarm
+
+power1_label "pin"
+power1_input Measured input power
+power1_alarm Input power alarm
+power1_max Maximum input power
+
+power2_label "pout1"
+power2_input Measured output power
+power2_max Maximum output power
+power2_max_alarm Output power high alarm
+
+temp1_input Measured temperature around input connector
+temp1_alarm Temperature alarm
+
+temp2_input Measured temperature around output connector
+temp2_alarm Temperature alarm
+======================= ============================================
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 32d2fc850621..c9f08725d201 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -56,6 +56,15 @@ config SENSORS_BEL_PFE
This driver can also be built as a module. If so, the module will
be called bel-pfe.
+config SENSORS_BPA_RS600
+ tristate "BluTek BPD-RS600 Power Supplies"
+ help
+ If you say yes here you get hardware monitoring support for BluTek
+ BPD-RS600 Power Supplies.
+
+ This driver can also be built as a module. If so, the module will
+ be called bpd-rs600.
+
config SENSORS_IBM_CFFPS
tristate "IBM Common Form Factor Power Supply"
depends on LEDS_CLASS
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 6a4ba0fdc1db..80a437060dc4 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
obj-$(CONFIG_SENSORS_ADM1266) += adm1266.o
obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
obj-$(CONFIG_SENSORS_BEL_PFE) += bel-pfe.o
+obj-$(CONFIG_SENSORS_BPA_RS600) += bpa-rs600.o
obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
obj-$(CONFIG_SENSORS_INSPUR_IPSPS) += inspur-ipsps.o
obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
diff --git a/drivers/hwmon/pmbus/bpa-rs600.c b/drivers/hwmon/pmbus/bpa-rs600.c
new file mode 100644
index 000000000000..bdfdef86bf1e
--- /dev/null
+++ b/drivers/hwmon/pmbus/bpa-rs600.c
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for BluTek BPA-RS600 Power Supplies
+ *
+ * Copyright 2021 Allied Telesis Labs
+ */
+
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pmbus.h>
+#include "pmbus.h"
+
+#define BPARS600_MFR_VIN_MIN 0xa0
+#define BPARS600_MFR_VIN_MAX 0xa1
+#define BPARS600_MFR_IIN_MAX 0xa2
+#define BPARS600_MFR_PIN_MAX 0xa3
+#define BPARS600_MFR_VOUT_MIN 0xa4
+#define BPARS600_MFR_VOUT_MAX 0xa5
+#define BPARS600_MFR_IOUT_MAX 0xa6
+#define BPARS600_MFR_POUT_MAX 0xa7
+
+static int bpa_rs600_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+ int ret;
+
+ if (page > 0)
+ return -ENXIO;
+
+ switch (reg) {
+ case PMBUS_FAN_CONFIG_12:
+ /*
+ * Two fans are reported in PMBUS_FAN_CONFIG_12 but there is
+ * only one fan in the module. Mask out the FAN2 bits.
+ */
+ ret = pmbus_read_byte_data(client, 0, PMBUS_FAN_CONFIG_12);
+ if (ret >= 0)
+ ret &= ~(PB_FAN_2_INSTALLED | PB_FAN_2_PULSE_MASK);
+ break;
+ default:
+ ret = -ENODATA;
+ break;
+ }
+
+ return ret;
+}
+
+static int bpa_rs600_read_word_data(struct i2c_client *client, int page, int phase, int reg)
+{
+ int ret;
+
+ if (page > 0)
+ return -ENXIO;
+
+ switch (reg) {
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_VIN_MIN);
+ break;
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_VIN_MAX);
+ break;
+ case PMBUS_VOUT_UV_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_VOUT_MIN);
+ break;
+ case PMBUS_VOUT_OV_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_VOUT_MAX);
+ break;
+ case PMBUS_IIN_OC_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_IIN_MAX);
+ break;
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_IOUT_MAX);
+ break;
+ case PMBUS_PIN_OP_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_PIN_MAX);
+ break;
+ case PMBUS_POUT_OP_WARN_LIMIT:
+ ret = pmbus_read_word_data(client, 0, 0xff, BPARS600_MFR_POUT_MAX);
+ break;
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ /* These commands return data but it is invalid/un-documented */
+ ret = -ENXIO;
+ break;
+ default:
+ if (reg >= PMBUS_VIRT_BASE)
+ ret = -ENXIO;
+ else
+ ret = -ENODATA;
+ break;
+ }
+
+ return ret;
+}
+
+static struct pmbus_driver_info bpa_rs600_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_FAN] = linear,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT |
+ PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_POUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
+ PMBUS_HAVE_FAN12 |
+ PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_STATUS_TEMP |
+ PMBUS_HAVE_STATUS_FAN12,
+ .read_byte_data = bpa_rs600_read_byte_data,
+ .read_word_data = bpa_rs600_read_word_data,
+};
+
+static int bpa_rs600_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ u8 buf[I2C_SMBUS_BLOCK_MAX];
+ int ret;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_BYTE_DATA
+ | I2C_FUNC_SMBUS_READ_WORD_DATA
+ | I2C_FUNC_SMBUS_READ_BLOCK_DATA))
+ return -ENODEV;
+
+ ret = i2c_smbus_read_block_data(client, PMBUS_MFR_MODEL, buf);
+ if (ret < 0) {
+ dev_err(dev, "Failed to read Manufacturer Model\n");
+ return ret;
+ }
+
+ if (strncmp(buf, "BPA-RS600", 8)) {
+ buf[ret] = '\0';
+ dev_err(dev, "Unsupported Manufacturer Model '%s'\n", buf);
+ return -ENODEV;
+ }
+
+ return pmbus_do_probe(client, &bpa_rs600_info);
+}
+
+static const struct i2c_device_id bpa_rs600_id[] = {
+ { "bpars600", 0 },
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, bpa_rs600_id);
+
+static const struct of_device_id __maybe_unused bpa_rs600_of_match[] = {
+ { .compatible = "blutek,bpa-rs600" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bpa_rs600_of_match);
+
+static struct i2c_driver bpa_rs600_driver = {
+ .driver = {
+ .name = "bpa-rs600",
+ .of_match_table = of_match_ptr(bpa_rs600_of_match),
+ },
+ .probe_new = bpa_rs600_probe,
+ .id_table = bpa_rs600_id,
+};
+
+module_i2c_driver(bpa_rs600_driver);
+
+MODULE_AUTHOR("Chris Packham");
+MODULE_DESCRIPTION("PMBus driver for BluTek BPA-RS600");
+MODULE_LICENSE("GPL");
--
2.30.2
Powered by blists - more mailing lists