| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5cb96462-d3b1-5938-706a-e50204188d77@codeaurora.org>
Date: Thu, 18 Mar 2021 12:03:00 -0700
From: "Asutosh Das (asd)" <asutoshd@...eaurora.org>
To: Adrian Hunter <adrian.hunter@...el.com>, cang@...eaurora.org,
martin.petersen@...cle.com, linux-scsi@...r.kernel.org
Cc: linux-arm-msm@...r.kernel.org,
Alim Akhtar <alim.akhtar@...sung.com>,
Avri Altman <avri.altman@....com>,
"James E.J. Bottomley" <jejb@...ux.ibm.com>,
Pedro Sousa <pedrom.sousa@...opsys.com>,
Krzysztof Kozlowski <krzk@...nel.org>,
Stanley Chu <stanley.chu@...iatek.com>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Steven Rostedt <rostedt@...dmis.org>,
Ingo Molnar <mingo@...hat.com>,
Matthias Brugger <matthias.bgg@...il.com>,
Bean Huo <beanhuo@...ron.com>,
Kiwoong Kim <kwmad.kim@...sung.com>,
Wei Yongjun <weiyongjun1@...wei.com>,
Lee Jones <lee.jones@...aro.org>,
"Gustavo A. R. Silva" <gustavoars@...nel.org>,
Dinghao Liu <dinghao.liu@....edu.cn>,
Jaegeuk Kim <jaegeuk@...nel.org>,
Satya Tangirala <satyat@...gle.com>,
open list <linux-kernel@...r.kernel.org>,
"moderated list:ARM/SAMSUNG S3C, S5P AND EXYNOS ARM ARCHITECTURES"
<linux-arm-kernel@...ts.infradead.org>,
"open list:ARM/SAMSUNG S3C, S5P AND EXYNOS ARM ARCHITECTURES"
<linux-samsung-soc@...r.kernel.org>,
"moderated list:UNIVERSAL FLASH STORAGE HOST CONTROLLER DRIVER..."
<linux-mediatek@...ts.infradead.org>
Subject: Re: [PATCH v11 1/2] scsi: ufs: Enable power management for wlun
On 3/15/2021 7:29 AM, Adrian Hunter wrote:
> On 12/03/21 12:19 am, Asutosh Das wrote:
>> During runtime-suspend of ufs host, the scsi devices are
>> already suspended and so are the queues associated with them.
>> But the ufs host sends SSU to wlun during its runtime-suspend.
>> During the process blk_queue_enter checks if the queue is not in
>> suspended state. If so, it waits for the queue to resume, and never
>> comes out of it.
>> The commit
>> (d55d15a33: scsi: block: Do not accept any requests while suspended)
>> adds the check if the queue is in suspended state in blk_queue_enter().
>>
>> Call trace:
>> __switch_to+0x174/0x2c4
>> __schedule+0x478/0x764
>> schedule+0x9c/0xe0
>> blk_queue_enter+0x158/0x228
>> blk_mq_alloc_request+0x40/0xa4
>> blk_get_request+0x2c/0x70
>> __scsi_execute+0x60/0x1c4
>> ufshcd_set_dev_pwr_mode+0x124/0x1e4
>> ufshcd_suspend+0x208/0x83c
>> ufshcd_runtime_suspend+0x40/0x154
>> ufshcd_pltfrm_runtime_suspend+0x14/0x20
>> pm_generic_runtime_suspend+0x28/0x3c
>> __rpm_callback+0x80/0x2a4
>> rpm_suspend+0x308/0x614
>> rpm_idle+0x158/0x228
>> pm_runtime_work+0x84/0xac
>> process_one_work+0x1f0/0x470
>> worker_thread+0x26c/0x4c8
>> kthread+0x13c/0x320
>> ret_from_fork+0x10/0x18
>>
>> Fix this by registering ufs device wlun as a scsi driver and
>> registering it for block runtime-pm. Also make this as a
>> supplier for all other luns. That way, this device wlun
>> suspends after all the consumers and resumes after
>> hba resumes.
>
> I haven't had time to try to reproduce the device-links issue, but
> there are a couple of comments below, in addition to the suggestions
> here:
>
> https://lore.kernel.org/linux-scsi/b13086f3-eea1-51a7-2117-579d520f21fc@intel.com/
>
Thanks.
I think even if the race in pm framework is fixed, the
scsi_sysfs_add_sdev() can race with sd_probe().
IIUC that's because scsi_sysfs_add_sdev() schedules an async probe for
the sd device and then invokes scsi_autopm_put_device().
> Also, there are still ufshcd_err_handling_prepare()/unprepare()
> and ufshcd_recover_pm_error(), that look like they need attention
> e.g. to use scsi_autopm_get/put_device(hba->sdev_ufs_device)
>
Sure will address this.
>
>>
>> Co-developed-by: Can Guo <cang@...eaurora.org>
>> Signed-off-by: Can Guo <cang@...eaurora.org>
>> Signed-off-by: Asutosh Das <asutoshd@...eaurora.org>
>> ---
>> drivers/scsi/ufs/cdns-pltfrm.c | 2 +
>> drivers/scsi/ufs/tc-dwc-g210-pci.c | 2 +
>> drivers/scsi/ufs/ufs-debugfs.c | 5 +
>> drivers/scsi/ufs/ufs-debugfs.h | 2 +
>> drivers/scsi/ufs/ufs-exynos.c | 2 +
>> drivers/scsi/ufs/ufs-hisi.c | 2 +
>> drivers/scsi/ufs/ufs-mediatek.c | 2 +
>> drivers/scsi/ufs/ufs-qcom.c | 2 +
>> drivers/scsi/ufs/ufs_bsg.c | 6 +-
>> drivers/scsi/ufs/ufshcd-pci.c | 36 +--
>> drivers/scsi/ufs/ufshcd.c | 616 ++++++++++++++++++++++++++-----------
>> drivers/scsi/ufs/ufshcd.h | 7 +
>> include/trace/events/ufs.h | 20 ++
>> 13 files changed, 498 insertions(+), 206 deletions(-)
>>
>> diff --git a/drivers/scsi/ufs/cdns-pltfrm.c b/drivers/scsi/ufs/cdns-pltfrm.c
>> index 149391f..3e70c23 100644
>> --- a/drivers/scsi/ufs/cdns-pltfrm.c
>> +++ b/drivers/scsi/ufs/cdns-pltfrm.c
>> @@ -319,6 +319,8 @@ static const struct dev_pm_ops cdns_ufs_dev_pm_ops = {
>> .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
>> .runtime_resume = ufshcd_pltfrm_runtime_resume,
>> .runtime_idle = ufshcd_pltfrm_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static struct platform_driver cdns_ufs_pltfrm_driver = {
>> diff --git a/drivers/scsi/ufs/tc-dwc-g210-pci.c b/drivers/scsi/ufs/tc-dwc-g210-pci.c
>> index 67a6a61..b01db12 100644
>> --- a/drivers/scsi/ufs/tc-dwc-g210-pci.c
>> +++ b/drivers/scsi/ufs/tc-dwc-g210-pci.c
>> @@ -148,6 +148,8 @@ static const struct dev_pm_ops tc_dwc_g210_pci_pm_ops = {
>> .runtime_suspend = tc_dwc_g210_pci_runtime_suspend,
>> .runtime_resume = tc_dwc_g210_pci_runtime_resume,
>> .runtime_idle = tc_dwc_g210_pci_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static const struct pci_device_id tc_dwc_g210_pci_tbl[] = {
>> diff --git a/drivers/scsi/ufs/ufs-debugfs.c b/drivers/scsi/ufs/ufs-debugfs.c
>> index dee98dc..f8ce2eb 100644
>> --- a/drivers/scsi/ufs/ufs-debugfs.c
>> +++ b/drivers/scsi/ufs/ufs-debugfs.c
>> @@ -54,3 +54,8 @@ void ufs_debugfs_hba_exit(struct ufs_hba *hba)
>> {
>> debugfs_remove_recursive(hba->debugfs_root);
>> }
>> +
>> +void ufs_debugfs_eh_exit(void)
>> +{
>> + debugfs_remove_recursive(ufs_debugfs_root);
>> +}
>
> This is the same as ufs_debugfs_exit() without __exit so why not
> remove __exit from ufs_debugfs_exit() and use that instead?
>
Will change it.
>> diff --git a/drivers/scsi/ufs/ufs-debugfs.h b/drivers/scsi/ufs/ufs-debugfs.h
>> index f35b39c..3fce5a0 100644
>> --- a/drivers/scsi/ufs/ufs-debugfs.h
>> +++ b/drivers/scsi/ufs/ufs-debugfs.h
>> @@ -12,11 +12,13 @@ void __init ufs_debugfs_init(void);
>> void __exit ufs_debugfs_exit(void);
>> void ufs_debugfs_hba_init(struct ufs_hba *hba);
>> void ufs_debugfs_hba_exit(struct ufs_hba *hba);
>> +void ufs_debugfs_eh_exit(void);
>> #else
>> static inline void ufs_debugfs_init(void) {}
>> static inline void ufs_debugfs_exit(void) {}
>> static inline void ufs_debugfs_hba_init(struct ufs_hba *hba) {}
>> static inline void ufs_debugfs_hba_exit(struct ufs_hba *hba) {}
>> +static inline void ufs_debugfs_eh_exit(void) {}
>> #endif
>>
>> #endif
>> diff --git a/drivers/scsi/ufs/ufs-exynos.c b/drivers/scsi/ufs/ufs-exynos.c
>> index 267943a1..45c0b02 100644
>> --- a/drivers/scsi/ufs/ufs-exynos.c
>> +++ b/drivers/scsi/ufs/ufs-exynos.c
>> @@ -1268,6 +1268,8 @@ static const struct dev_pm_ops exynos_ufs_pm_ops = {
>> .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
>> .runtime_resume = ufshcd_pltfrm_runtime_resume,
>> .runtime_idle = ufshcd_pltfrm_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static struct platform_driver exynos_ufs_pltform = {
>> diff --git a/drivers/scsi/ufs/ufs-hisi.c b/drivers/scsi/ufs/ufs-hisi.c
>> index 0aa5813..d463b44 100644
>> --- a/drivers/scsi/ufs/ufs-hisi.c
>> +++ b/drivers/scsi/ufs/ufs-hisi.c
>> @@ -574,6 +574,8 @@ static const struct dev_pm_ops ufs_hisi_pm_ops = {
>> .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
>> .runtime_resume = ufshcd_pltfrm_runtime_resume,
>> .runtime_idle = ufshcd_pltfrm_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static struct platform_driver ufs_hisi_pltform = {
>> diff --git a/drivers/scsi/ufs/ufs-mediatek.c b/drivers/scsi/ufs/ufs-mediatek.c
>> index c55202b..df1eabb 100644
>> --- a/drivers/scsi/ufs/ufs-mediatek.c
>> +++ b/drivers/scsi/ufs/ufs-mediatek.c
>> @@ -1097,6 +1097,8 @@ static const struct dev_pm_ops ufs_mtk_pm_ops = {
>> .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
>> .runtime_resume = ufshcd_pltfrm_runtime_resume,
>> .runtime_idle = ufshcd_pltfrm_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static struct platform_driver ufs_mtk_pltform = {
>> diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
>> index f97d7b0..9aa098a 100644
>> --- a/drivers/scsi/ufs/ufs-qcom.c
>> +++ b/drivers/scsi/ufs/ufs-qcom.c
>> @@ -1546,6 +1546,8 @@ static const struct dev_pm_ops ufs_qcom_pm_ops = {
>> .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
>> .runtime_resume = ufshcd_pltfrm_runtime_resume,
>> .runtime_idle = ufshcd_pltfrm_runtime_idle,
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> };
>>
>> static struct platform_driver ufs_qcom_pltform = {
>> diff --git a/drivers/scsi/ufs/ufs_bsg.c b/drivers/scsi/ufs/ufs_bsg.c
>> index 5b2bc1a..cbb5a90 100644
>> --- a/drivers/scsi/ufs/ufs_bsg.c
>> +++ b/drivers/scsi/ufs/ufs_bsg.c
>> @@ -97,7 +97,7 @@ static int ufs_bsg_request(struct bsg_job *job)
>>
>> bsg_reply->reply_payload_rcv_len = 0;
>>
>> - pm_runtime_get_sync(hba->dev);
>> + scsi_autopm_get_device(hba->sdev_ufs_device);
>>
>> msgcode = bsg_request->msgcode;
>> switch (msgcode) {
>> @@ -106,7 +106,7 @@ static int ufs_bsg_request(struct bsg_job *job)
>> ret = ufs_bsg_alloc_desc_buffer(hba, job, &desc_buff,
>> &desc_len, desc_op);
>> if (ret) {
>> - pm_runtime_put_sync(hba->dev);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>> goto out;
>> }
>>
>> @@ -138,7 +138,7 @@ static int ufs_bsg_request(struct bsg_job *job)
>> break;
>> }
>>
>> - pm_runtime_put_sync(hba->dev);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>>
>> if (!desc_buff)
>> goto out;
>> diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c
>> index fadd566..5d4ffd2 100644
>> --- a/drivers/scsi/ufs/ufshcd-pci.c
>> +++ b/drivers/scsi/ufs/ufshcd-pci.c
>> @@ -247,29 +247,6 @@ static int ufshcd_pci_resume(struct device *dev)
>> return ufshcd_system_resume(dev_get_drvdata(dev));
>> }
>>
>> -/**
>> - * ufshcd_pci_poweroff - suspend-to-disk poweroff function
>> - * @dev: pointer to PCI device handle
>> - *
>> - * Returns 0 if successful
>> - * Returns non-zero otherwise
>> - */
>> -static int ufshcd_pci_poweroff(struct device *dev)
>> -{
>> - struct ufs_hba *hba = dev_get_drvdata(dev);
>> - int spm_lvl = hba->spm_lvl;
>> - int ret;
>> -
>> - /*
>> - * For poweroff we need to set the UFS device to PowerDown mode.
>> - * Force spm_lvl to ensure that.
>> - */
>> - hba->spm_lvl = 5;
>> - ret = ufshcd_system_suspend(hba);
>> - hba->spm_lvl = spm_lvl;
>> - return ret;
>> -}
>> -
>> #endif /* !CONFIG_PM_SLEEP */
>>
>> #ifdef CONFIG_PM
>> @@ -365,17 +342,14 @@ ufshcd_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>> }
>>
>> static const struct dev_pm_ops ufshcd_pci_pm_ops = {
>> -#ifdef CONFIG_PM_SLEEP
>> - .suspend = ufshcd_pci_suspend,
>> - .resume = ufshcd_pci_resume,
>> - .freeze = ufshcd_pci_suspend,
>> - .thaw = ufshcd_pci_resume,
>> - .poweroff = ufshcd_pci_poweroff,
>> - .restore = ufshcd_pci_resume,
>> -#endif
>> SET_RUNTIME_PM_OPS(ufshcd_pci_runtime_suspend,
>> ufshcd_pci_runtime_resume,
>> ufshcd_pci_runtime_idle)
>> + SET_SYSTEM_SLEEP_PM_OPS(ufshcd_pci_suspend, ufshcd_pci_resume)
>> +#ifdef CONFIG_PM_SLEEP
>> + .prepare = ufshcd_suspend_prepare,
>> + .complete = ufshcd_resume_complete,
>> +#endif
>> };
>>
>> static const struct pci_device_id ufshcd_pci_tbl[] = {
>> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
>> index 45624c7..254f952 100644
>> --- a/drivers/scsi/ufs/ufshcd.c
>> +++ b/drivers/scsi/ufs/ufshcd.c
>> @@ -16,6 +16,7 @@
>> #include <linux/bitfield.h>
>> #include <linux/blk-pm.h>
>> #include <linux/blkdev.h>
>> +#include <scsi/scsi_driver.h>
>> #include "ufshcd.h"
>> #include "ufs_quirks.h"
>> #include "unipro.h"
>> @@ -78,6 +79,8 @@
>> /* Polling time to wait for fDeviceInit */
>> #define FDEVICEINIT_COMPL_TIMEOUT 1500 /* millisecs */
>>
>> +#define wlun_dev_to_hba(dv) shost_priv(to_scsi_device(dv)->host)
>> +
>> #define ufshcd_toggle_vreg(_dev, _vreg, _on) \
>> ({ \
>> int _ret; \
>> @@ -1556,7 +1559,7 @@ static ssize_t ufshcd_clkscale_enable_store(struct device *dev,
>> if (value == hba->clk_scaling.is_enabled)
>> goto out;
>>
>> - pm_runtime_get_sync(hba->dev);
>> + scsi_autopm_get_device(hba->sdev_ufs_device);
>> ufshcd_hold(hba, false);
>>
>> hba->clk_scaling.is_enabled = value;
>> @@ -1572,7 +1575,7 @@ static ssize_t ufshcd_clkscale_enable_store(struct device *dev,
>> }
>>
>> ufshcd_release(hba);
>> - pm_runtime_put_sync(hba->dev);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>> out:
>> up(&hba->host_sem);
>> return err ? err : count;
>> @@ -2572,6 +2575,17 @@ static inline u16 ufshcd_upiu_wlun_to_scsi_wlun(u8 upiu_wlun_id)
>> return (upiu_wlun_id & ~UFS_UPIU_WLUN_ID) | SCSI_W_LUN_BASE;
>> }
>>
>> +static inline bool is_rpmb_wlun(struct scsi_device *sdev)
>> +{
>> + return (sdev->lun == ufshcd_upiu_wlun_to_scsi_wlun(UFS_UPIU_RPMB_WLUN));
>> +}
>> +
>> +static inline bool is_device_wlun(struct scsi_device *sdev)
>> +{
>> + return (sdev->lun ==
>> + ufshcd_upiu_wlun_to_scsi_wlun(UFS_UPIU_UFS_DEVICE_WLUN));
>> +}
>> +
>> static void ufshcd_init_lrb(struct ufs_hba *hba, struct ufshcd_lrb *lrb, int i)
>> {
>> struct utp_transfer_cmd_desc *cmd_descp = hba->ucdl_base_addr;
>> @@ -4106,11 +4120,11 @@ void ufshcd_auto_hibern8_update(struct ufs_hba *hba, u32 ahit)
>> spin_unlock_irqrestore(hba->host->host_lock, flags);
>>
>> if (update && !pm_runtime_suspended(hba->dev)) {
>> - pm_runtime_get_sync(hba->dev);
>> + scsi_autopm_get_device(hba->sdev_ufs_device);
>
> ufs-mediatek.c calls ufshcd_auto_hibern8_update() at link startup when
> hba->sdev_ufs_device can be NULL.
>
>
Missed this, will fix and push in the next version.
>> ufshcd_hold(hba, false);
>> ufshcd_auto_hibern8_enable(hba);
>> ufshcd_release(hba);
>> - pm_runtime_put(hba->dev);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>> }
>> }
>> EXPORT_SYMBOL_GPL(ufshcd_auto_hibern8_update);
>> @@ -4808,6 +4822,38 @@ static inline void ufshcd_get_lu_power_on_wp_status(struct ufs_hba *hba,
>> }
>>
>> /**
>> + * ufshcd_setup_links - associate link b/w device wlun and other luns
>> + * @sdev: pointer to SCSI device
>> + * @hba: pointer to ufs hba
>> + */
>> +static void ufshcd_setup_links(struct ufs_hba *hba, struct scsi_device *sdev)
>> +{
>> + struct device_link *link;
>> +
>> + /*
>> + * device wlun is the supplier & rest of the luns are consumers
>> + * This ensures that device wlun suspends after all other luns.
>> + */
>> + if (hba->sdev_ufs_device) {
>> + link = device_link_add(&sdev->sdev_gendev,
>> + &hba->sdev_ufs_device->sdev_gendev,
>> + DL_FLAG_PM_RUNTIME|DL_FLAG_RPM_ACTIVE);
>> + if (!link) {
>> + dev_err(&sdev->sdev_gendev, "Failed establishing link - %s\n",
>> + dev_name(&hba->sdev_ufs_device->sdev_gendev));
>> + return;
>> + }
>> + hba->luns_avail--;
>> + /* Ignore REPORT_LUN wlun probing */
>> + if (hba->luns_avail != 1)
>> + return;
>> + } else {
>> + /* device wlun is probed */
>> + hba->luns_avail--;
>> + }
>> +}
>> +
>> +/**
>> * ufshcd_slave_alloc - handle initial SCSI device configurations
>> * @sdev: pointer to SCSI device
>> *
>> @@ -4838,6 +4884,8 @@ static int ufshcd_slave_alloc(struct scsi_device *sdev)
>>
>> ufshcd_get_lu_power_on_wp_status(hba, sdev);
>>
>> + ufshcd_setup_links(hba, sdev);
>> +
>> return 0;
>> }
>>
>> @@ -4875,6 +4923,17 @@ static int ufshcd_slave_configure(struct scsi_device *sdev)
>>
>> ufshcd_crypto_setup_rq_keyslot_manager(hba, q);
>>
>> + /*
>> + * sd_probe() runs asynchronously with scsi_sysfs_add_sdev().
>> + * Say, scsi_sysfs_add_sdev() suspends just before sd_probe()
>> + * it'd reset the link's rpm_active to 1.
>> + * That may cause the supplier to suspend before the consumer,
>> + * which is bad.
>> + * So block runtime-pm until all devices are probed.
>> + * Refer ufshcd_scsi_sync_probe().
>> + */
>> + pm_runtime_forbid(&sdev->sdev_gendev);
>> +
>> return 0;
>> }
>>
>> @@ -4985,15 +5044,9 @@ ufshcd_transfer_rsp_status(struct ufs_hba *hba, struct ufshcd_lrb *lrbp)
>> * UFS device needs urgent BKOPs.
>> */
>> if (!hba->pm_op_in_progress &&
>> - ufshcd_is_exception_event(lrbp->ucd_rsp_ptr) &&
>> - schedule_work(&hba->eeh_work)) {
>> - /*
>> - * Prevent suspend once eeh_work is scheduled
>> - * to avoid deadlock between ufshcd_suspend
>> - * and exception event handler.
>> - */
>> - pm_runtime_get_noresume(hba->dev);
>> - }
>> + ufshcd_is_exception_event(lrbp->ucd_rsp_ptr))
>> + /* Flushed in suspend */
>> + schedule_work(&hba->eeh_work);
>> break;
>> case UPIU_TRANSACTION_REJECT_UPIU:
>> /* TODO: handle Reject UPIU Response */
>> @@ -5589,8 +5642,8 @@ static void ufshcd_rpm_dev_flush_recheck_work(struct work_struct *work)
>> * after a certain delay to recheck the threshold by next runtime
>> * suspend.
>> */
>> - pm_runtime_get_sync(hba->dev);
>> - pm_runtime_put_sync(hba->dev);
>> + scsi_autopm_get_device(hba->sdev_ufs_device);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>> }
>>
>> /**
>> @@ -5607,7 +5660,6 @@ static void ufshcd_exception_event_handler(struct work_struct *work)
>> u32 status = 0;
>> hba = container_of(work, struct ufs_hba, eeh_work);
>>
>> - pm_runtime_get_sync(hba->dev);
>> ufshcd_scsi_block_requests(hba);
>> err = ufshcd_get_ee_status(hba, &status);
>> if (err) {
>> @@ -5623,14 +5675,6 @@ static void ufshcd_exception_event_handler(struct work_struct *work)
>>
>> out:
>> ufshcd_scsi_unblock_requests(hba);
>> - /*
>> - * pm_runtime_get_noresume is called while scheduling
>> - * eeh_work to avoid suspend racing with exception work.
>> - * Hence decrement usage counter using pm_runtime_put_noidle
>> - * to allow suspend on completion of exception event handler.
>> - */
>> - pm_runtime_put_noidle(hba->dev);
>> - pm_runtime_put(hba->dev);
>> return;
>> }
>>
>> @@ -7207,11 +7251,12 @@ static void ufshcd_set_active_icc_lvl(struct ufs_hba *hba)
>>
>> static inline void ufshcd_blk_pm_runtime_init(struct scsi_device *sdev)
>> {
>> + int dly = is_device_wlun(sdev) ? 0:RPM_AUTOSUSPEND_DELAY_MS;
>> +
>> scsi_autopm_get_device(sdev);
>> blk_pm_runtime_init(sdev->request_queue, &sdev->sdev_gendev);
>> if (sdev->rpm_autosuspend)
>> - pm_runtime_set_autosuspend_delay(&sdev->sdev_gendev,
>> - RPM_AUTOSUSPEND_DELAY_MS);
>> + pm_runtime_set_autosuspend_delay(&sdev->sdev_gendev, dly);
>> scsi_autopm_put_device(sdev);
>> }
>>
>> @@ -7417,6 +7462,9 @@ static int ufs_get_device_desc(struct ufs_hba *hba)
>> goto out;
>> }
>>
>> + hba->luns_avail = desc_buf[DEVICE_DESC_PARAM_NUM_LU] +
>> + desc_buf[DEVICE_DESC_PARAM_NUM_WLU];
>> +
>> ufs_fixup_device_setup(hba);
>>
>> ufshcd_wb_probe(hba, desc_buf);
>> @@ -7892,6 +7940,7 @@ static int ufshcd_probe_hba(struct ufs_hba *hba, bool async)
>> ufshcd_set_ufs_dev_active(hba);
>> ufshcd_force_reset_auto_bkops(hba);
>> hba->wlun_dev_clr_ua = true;
>> + hba->wlun_rpmb_clr_ua = true;
>>
>> /* Gear up to HS gear if supported */
>> if (hba->max_pwr_info.is_valid) {
>> @@ -8475,7 +8524,8 @@ static int ufshcd_set_dev_pwr_mode(struct ufs_hba *hba,
>> * handling context.
>> */
>> hba->host->eh_noresume = 1;
>> - ufshcd_clear_ua_wluns(hba);
>> + if (hba->wlun_dev_clr_ua)
>> + ufshcd_clear_ua_wlun(hba, UFS_UPIU_UFS_DEVICE_WLUN);
>>
>> cmd[4] = pwr_mode << 4;
>>
>> @@ -8650,23 +8700,7 @@ static void ufshcd_hba_vreg_set_hpm(struct ufs_hba *hba)
>> ufshcd_setup_hba_vreg(hba, true);
>> }
>>
>> -/**
>> - * ufshcd_suspend - helper function for suspend operations
>> - * @hba: per adapter instance
>> - * @pm_op: desired low power operation type
>> - *
>> - * This function will try to put the UFS device and link into low power
>> - * mode based on the "rpm_lvl" (Runtime PM level) or "spm_lvl"
>> - * (System PM level).
>> - *
>> - * If this function is called during shutdown, it will make sure that
>> - * both UFS device and UFS link is powered off.
>> - *
>> - * NOTE: UFS device & link must be active before we enter in this function.
>> - *
>> - * Returns 0 for success and non-zero for failure
>> - */
>> -static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> +static int __ufshcd_wl_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> {
>> int ret = 0;
>> int check_for_bkops;
>> @@ -8674,7 +8708,7 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> enum ufs_dev_pwr_mode req_dev_pwr_mode;
>> enum uic_link_state req_link_state;
>>
>> - hba->pm_op_in_progress = 1;
>> + hba->pm_op_in_progress = true;
>> if (!ufshcd_is_shutdown_pm(pm_op)) {
>> pm_lvl = ufshcd_is_runtime_pm(pm_op) ?
>> hba->rpm_lvl : hba->spm_lvl;
>> @@ -8697,17 +8731,17 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>>
>> if (req_dev_pwr_mode == UFS_ACTIVE_PWR_MODE &&
>> req_link_state == UIC_LINK_ACTIVE_STATE) {
>> - goto disable_clks;
>> + goto enable_scaling;
>> }
>>
>> if ((req_dev_pwr_mode == hba->curr_dev_pwr_mode) &&
>> (req_link_state == hba->uic_link_state))
>> - goto enable_gating;
>> + goto enable_scaling;
>>
>> /* UFS device & link must be active before we enter in this function */
>> if (!ufshcd_is_ufs_dev_active(hba) || !ufshcd_is_link_active(hba)) {
>> ret = -EINVAL;
>> - goto enable_gating;
>> + goto enable_scaling;
>> }
>>
>> if (ufshcd_is_runtime_pm(pm_op)) {
>> @@ -8719,7 +8753,7 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> */
>> ret = ufshcd_urgent_bkops(hba);
>> if (ret)
>> - goto enable_gating;
>> + goto enable_scaling;
>> } else {
>> /* make sure that auto bkops is disabled */
>> ufshcd_disable_auto_bkops(hba);
>> @@ -8747,7 +8781,7 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> if (!hba->dev_info.b_rpm_dev_flush_capable) {
>> ret = ufshcd_set_dev_pwr_mode(hba, req_dev_pwr_mode);
>> if (ret)
>> - goto enable_gating;
>> + goto enable_scaling;
>> }
>> }
>>
>> @@ -8760,7 +8794,6 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> if (ret)
>> goto set_dev_active;
>>
>> -disable_clks:
>> /*
>> * Call vendor specific suspend callback. As these callbacks may access
>> * vendor specific host controller register space call them before the
>> @@ -8769,28 +8802,9 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> ret = ufshcd_vops_suspend(hba, pm_op);
>> if (ret)
>> goto set_link_active;
>> - /*
>> - * Disable the host irq as host controller as there won't be any
>> - * host controller transaction expected till resume.
>> - */
>> - ufshcd_disable_irq(hba);
>> -
>> - ufshcd_setup_clocks(hba, false);
>> -
>> - if (ufshcd_is_clkgating_allowed(hba)) {
>> - hba->clk_gating.state = CLKS_OFF;
>> - trace_ufshcd_clk_gating(dev_name(hba->dev),
>> - hba->clk_gating.state);
>> - }
>> -
>> - ufshcd_vreg_set_lpm(hba);
>> -
>> - /* Put the host controller in low power mode if possible */
>> - ufshcd_hba_vreg_set_lpm(hba);
>> goto out;
>>
>> set_link_active:
>> - ufshcd_vreg_set_hpm(hba);
>> /*
>> * Device hardware reset is required to exit DeepSleep. Also, for
>> * DeepSleep, the link is off so host reset and restore will be done
>> @@ -8812,57 +8826,32 @@ static int ufshcd_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> }
>> if (!ufshcd_set_dev_pwr_mode(hba, UFS_ACTIVE_PWR_MODE))
>> ufshcd_disable_auto_bkops(hba);
>> -enable_gating:
>> +enable_scaling:
>> if (ufshcd_is_clkscaling_supported(hba))
>> ufshcd_clk_scaling_suspend(hba, false);
>>
>> - hba->clk_gating.is_suspended = false;
>> hba->dev_info.b_rpm_dev_flush_capable = false;
>> - ufshcd_clear_ua_wluns(hba);
>> - ufshcd_release(hba);
>> out:
>> if (hba->dev_info.b_rpm_dev_flush_capable) {
>> schedule_delayed_work(&hba->rpm_dev_flush_recheck_work,
>> msecs_to_jiffies(RPM_DEV_FLUSH_RECHECK_WORK_DELAY_MS));
>> }
>>
>> - hba->pm_op_in_progress = 0;
>> -
>> - if (ret)
>> - ufshcd_update_evt_hist(hba, UFS_EVT_SUSPEND_ERR, (u32)ret);
>> + if (ret) {
>> + ufshcd_update_evt_hist(hba, UFS_EVT_WL_SUSP_ERR, (u32)ret);
>> + hba->clk_gating.is_suspended = false;
>> + ufshcd_release(hba);
>> + }
>> + hba->pm_op_in_progress = false;
>> return ret;
>> }
>>
>> -/**
>> - * ufshcd_resume - helper function for resume operations
>> - * @hba: per adapter instance
>> - * @pm_op: runtime PM or system PM
>> - *
>> - * This function basically brings the UFS device, UniPro link and controller
>> - * to active state.
>> - *
>> - * Returns 0 for success and non-zero for failure
>> - */
>> -static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> +static int __ufshcd_wl_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> {
>> int ret;
>> - enum uic_link_state old_link_state;
>> + enum uic_link_state old_link_state = hba->uic_link_state;
>>
>> - hba->pm_op_in_progress = 1;
>> - old_link_state = hba->uic_link_state;
>> -
>> - ufshcd_hba_vreg_set_hpm(hba);
>> - ret = ufshcd_vreg_set_hpm(hba);
>> - if (ret)
>> - goto out;
>> -
>> - /* Make sure clocks are enabled before accessing controller */
>> - ret = ufshcd_setup_clocks(hba, true);
>> - if (ret)
>> - goto disable_vreg;
>> -
>> - /* enable the host irq as host controller would be active soon */
>> - ufshcd_enable_irq(hba);
>> + hba->pm_op_in_progress = true;
>>
>> /*
>> * Call vendor specific resume callback. As these callbacks may access
>> @@ -8871,7 +8860,7 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> */
>> ret = ufshcd_vops_resume(hba, pm_op);
>> if (ret)
>> - goto disable_irq_and_vops_clks;
>> + goto out;
>>
>> /* For DeepSleep, the only supported option is to have the link off */
>> WARN_ON(ufshcd_is_ufs_dev_deepsleep(hba) && !ufshcd_is_link_off(hba));
>> @@ -8916,31 +8905,147 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> */
>> ufshcd_urgent_bkops(hba);
>>
>> - hba->clk_gating.is_suspended = false;
>> -
>> - if (ufshcd_is_clkscaling_supported(hba))
>> - ufshcd_clk_scaling_suspend(hba, false);
>> -
>> - /* Enable Auto-Hibernate if configured */
>> - ufshcd_auto_hibern8_enable(hba);
>> + if (hba->clk_scaling.is_allowed)
>> + ufshcd_resume_clkscaling(hba);
>>
>> if (hba->dev_info.b_rpm_dev_flush_capable) {
>> hba->dev_info.b_rpm_dev_flush_capable = false;
>> cancel_delayed_work(&hba->rpm_dev_flush_recheck_work);
>> }
>>
>> - ufshcd_clear_ua_wluns(hba);
>> -
>> - /* Schedule clock gating in case of no access to UFS device yet */
>> - ufshcd_release(hba);
>> -
>> + /* Enable Auto-Hibernate if configured */
>> + ufshcd_auto_hibern8_enable(hba);
>> goto out;
>>
>> set_old_link_state:
>> ufshcd_link_state_transition(hba, old_link_state, 0);
>> vendor_suspend:
>> ufshcd_vops_suspend(hba, pm_op);
>> -disable_irq_and_vops_clks:
>> +out:
>> + if (ret)
>> + ufshcd_update_evt_hist(hba, UFS_EVT_WL_RES_ERR, (u32)ret);
>> + hba->clk_gating.is_suspended = false;
>> + ufshcd_release(hba);
>> + hba->pm_op_in_progress = false;
>> + return ret;
>> +}
>> +
>> +static int ufshcd_wl_runtime_suspend(struct device *dev)
>> +{
>> + struct scsi_device *sdev = to_scsi_device(dev);
>> + struct ufs_hba *hba;
>> + int ret;
>> + ktime_t start = ktime_get();
>> +
>> + hba = shost_priv(sdev->host);
>> +
>> + ret = __ufshcd_wl_suspend(hba, UFS_RUNTIME_PM);
>> + if (ret)
>> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
>> +
>> + trace_ufshcd_wl_runtime_suspend(dev_name(dev), ret,
>> + ktime_to_us(ktime_sub(ktime_get(), start)),
>> + hba->curr_dev_pwr_mode, hba->uic_link_state);
>> +
>> + return ret;
>> +}
>> +
>> +static int ufshcd_wl_runtime_resume(struct device *dev)
>> +{
>> + struct scsi_device *sdev = to_scsi_device(dev);
>> + struct ufs_hba *hba;
>> + int ret = 0;
>> + ktime_t start = ktime_get();
>> +
>> + hba = shost_priv(sdev->host);
>> +
>> + ret = __ufshcd_wl_resume(hba, UFS_RUNTIME_PM);
>> + if (ret)
>> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
>> +
>> + trace_ufshcd_wl_runtime_resume(dev_name(dev), ret,
>> + ktime_to_us(ktime_sub(ktime_get(), start)),
>> + hba->curr_dev_pwr_mode, hba->uic_link_state);
>> +
>> + return ret;
>> +}
>> +
>> +#ifdef CONFIG_PM_SLEEP
>> +static int ufshcd_wl_suspend(struct device *dev)
>> +{
>> + struct scsi_device *sdev = to_scsi_device(dev);
>> + struct ufs_hba *hba;
>> + int ret;
>> + ktime_t start = ktime_get();
>> +
>> + hba = shost_priv(sdev->host);
>> + ret = __ufshcd_wl_suspend(hba, UFS_SYSTEM_PM);
>> + if (ret)
>> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
>> +
>> + trace_ufshcd_wl_suspend(dev_name(dev), ret,
>> + ktime_to_us(ktime_sub(ktime_get(), start)),
>> + hba->curr_dev_pwr_mode, hba->uic_link_state);
>> +
>> + return ret;
>> +}
>> +
>> +static int ufshcd_wl_resume(struct device *dev)
>> +{
>> + struct scsi_device *sdev = to_scsi_device(dev);
>> + struct ufs_hba *hba;
>> + int ret = 0;
>> + ktime_t start = ktime_get();
>> +
>> + if (pm_runtime_suspended(dev))
>> + return 0;
>> + hba = shost_priv(sdev->host);
>> +
>> + ret = __ufshcd_wl_resume(hba, UFS_SYSTEM_PM);
>> + if (ret)
>> + dev_err(&sdev->sdev_gendev, "%s failed: %d\n", __func__, ret);
>> +
>> + trace_ufshcd_wl_resume(dev_name(dev), ret,
>> + ktime_to_us(ktime_sub(ktime_get(), start)),
>> + hba->curr_dev_pwr_mode, hba->uic_link_state);
>> +
>> + return ret;
>> +}
>> +#endif
>> +
>> +static void ufshcd_wl_shutdown(struct device *dev)
>> +{
>> + struct scsi_device *sdev = to_scsi_device(dev);
>> + struct ufs_hba *hba;
>> +
>> + hba = shost_priv(sdev->host);
>> + /* Turn on everything while shutting down */
>> + scsi_autopm_get_device(sdev);
>> + scsi_device_quiesce(sdev);
>> + shost_for_each_device(sdev, hba->host) {
>> + if (sdev == hba->sdev_ufs_device)
>> + continue;
>> + scsi_device_quiesce(sdev);
>> + }
>> + __ufshcd_wl_suspend(hba, UFS_SHUTDOWN_PM);
>> +}
>> +
>> +/**
>> + * ufshcd_suspend - helper function for suspend operations
>> + * @hba: per adapter instance
>> + *
>> + * This function will put disable irqs, turn off clocks
>> + * and set vreg and hba-vreg in lpm mode.
>> + * Also check the description of __ufshcd_wl_suspend().
>> + */
>> +static void ufshcd_suspend(struct ufs_hba *hba)
>> +{
>> + hba->pm_op_in_progress = 1;
>> +
>> + /*
>> + * Disable the host irq as host controller as there won't be any
>> + * host controller transaction expected till resume.
>> + */
>> ufshcd_disable_irq(hba);
>> ufshcd_setup_clocks(hba, false);
>> if (ufshcd_is_clkgating_allowed(hba)) {
>> @@ -8948,6 +9053,43 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> trace_ufshcd_clk_gating(dev_name(hba->dev),
>> hba->clk_gating.state);
>> }
>> +
>> + ufshcd_vreg_set_lpm(hba);
>> + /* Put the host controller in low power mode if possible */
>> + ufshcd_hba_vreg_set_lpm(hba);
>> + hba->pm_op_in_progress = 0;
>> +}
>> +
>> +/**
>> + * ufshcd_resume - helper function for resume operations
>> + * @hba: per adapter instance
>> + *
>> + * This function basically turns on the regulators, clocks and
>> + * irqs of the hba.
>> + * Also check the description of __ufshcd_wl_resume().
>> + *
>> + * Returns 0 for success and non-zero for failure
>> + */
>> +static int ufshcd_resume(struct ufs_hba *hba)
>> +{
>> + int ret;
>> +
>> + hba->pm_op_in_progress = 1;
>> +
>> + ufshcd_hba_vreg_set_hpm(hba);
>> + ret = ufshcd_vreg_set_hpm(hba);
>> + if (ret)
>> + goto out;
>> +
>> + /* Make sure clocks are enabled before accessing controller */
>> + ret = ufshcd_setup_clocks(hba, true);
>> + if (ret)
>> + goto disable_vreg;
>> +
>> + /* enable the host irq as host controller would be active soon */
>> + ufshcd_enable_irq(hba);
>> + goto out;
>> +
>> disable_vreg:
>> ufshcd_vreg_set_lpm(hba);
>> out:
>> @@ -8962,6 +9104,7 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
>> * @hba: per adapter instance
>> *
>> * Check the description of ufshcd_suspend() function for more details.
>> + * Also check the description of __ufshcd_wl_suspend().
>> *
>> * Returns 0 for success and non-zero for failure
>> */
>> @@ -8987,21 +9130,7 @@ int ufshcd_system_suspend(struct ufs_hba *hba)
>> !hba->dev_info.b_rpm_dev_flush_capable)
>> goto out;
>>
>> - if (pm_runtime_suspended(hba->dev)) {
>> - /*
>> - * UFS device and/or UFS link low power states during runtime
>> - * suspend seems to be different than what is expected during
>> - * system suspend. Hence runtime resume the devic & link and
>> - * let the system suspend low power states to take effect.
>> - * TODO: If resume takes longer time, we might have optimize
>> - * it in future by not resuming everything if possible.
>> - */
>> - ret = ufshcd_runtime_resume(hba);
>> - if (ret)
>> - goto out;
>> - }
>> -
>> - ret = ufshcd_suspend(hba, UFS_SYSTEM_PM);
>> + ufshcd_suspend(hba);
>> out:
>> trace_ufshcd_system_suspend(dev_name(hba->dev), ret,
>> ktime_to_us(ktime_sub(ktime_get(), start)),
>> @@ -9023,7 +9152,6 @@ EXPORT_SYMBOL(ufshcd_system_suspend);
>>
>> int ufshcd_system_resume(struct ufs_hba *hba)
>> {
>> - int ret = 0;
>> ktime_t start = ktime_get();
>>
>> if (!hba)
>> @@ -9034,22 +9162,18 @@ int ufshcd_system_resume(struct ufs_hba *hba)
>> down(&hba->host_sem);
>> }
>>
>> - if (!hba->is_powered || pm_runtime_suspended(hba->dev))
>> - /*
>> - * Let the runtime resume take care of resuming
>> - * if runtime suspended.
>> - */
>> + if (!hba->is_powered)
>> goto out;
>> else
>> - ret = ufshcd_resume(hba, UFS_SYSTEM_PM);
>> + ufshcd_resume(hba);
>> out:
>> - trace_ufshcd_system_resume(dev_name(hba->dev), ret,
>> + trace_ufshcd_system_resume(dev_name(hba->dev), 0,
>> ktime_to_us(ktime_sub(ktime_get(), start)),
>> hba->curr_dev_pwr_mode, hba->uic_link_state);
>> - if (!ret)
>> - hba->is_sys_suspended = false;
>> +
>> + hba->is_sys_suspended = false;
>> up(&hba->host_sem);
>> - return ret;
>> + return 0;
>> }
>> EXPORT_SYMBOL(ufshcd_system_resume);
>>
>> @@ -9058,12 +9182,12 @@ EXPORT_SYMBOL(ufshcd_system_resume);
>> * @hba: per adapter instance
>> *
>> * Check the description of ufshcd_suspend() function for more details.
>> + * Also check the description of __ufshcd_wl_suspend().
>> *
>> * Returns 0 for success and non-zero for failure
>> */
>> int ufshcd_runtime_suspend(struct ufs_hba *hba)
>> {
>> - int ret = 0;
>> ktime_t start = ktime_get();
>>
>> if (!hba)
>> @@ -9072,12 +9196,12 @@ int ufshcd_runtime_suspend(struct ufs_hba *hba)
>> if (!hba->is_powered)
>> goto out;
>> else
>> - ret = ufshcd_suspend(hba, UFS_RUNTIME_PM);
>> + ufshcd_suspend(hba);
>> out:
>> - trace_ufshcd_runtime_suspend(dev_name(hba->dev), ret,
>> + trace_ufshcd_runtime_suspend(dev_name(hba->dev), 0,
>> ktime_to_us(ktime_sub(ktime_get(), start)),
>> hba->curr_dev_pwr_mode, hba->uic_link_state);
>> - return ret;
>> + return 0;
>> }
>> EXPORT_SYMBOL(ufshcd_runtime_suspend);
>>
>> @@ -9085,26 +9209,14 @@ EXPORT_SYMBOL(ufshcd_runtime_suspend);
>> * ufshcd_runtime_resume - runtime resume routine
>> * @hba: per adapter instance
>> *
>> - * This function basically brings the UFS device, UniPro link and controller
>> + * This function basically brings controller
>> * to active state. Following operations are done in this function:
>> *
>> * 1. Turn on all the controller related clocks
>> - * 2. Bring the UniPro link out of Hibernate state
>> - * 3. If UFS device is in sleep state, turn ON VCC rail and bring the UFS device
>> - * to active state.
>> - * 4. If auto-bkops is enabled on the device, disable it.
>> - *
>> - * So following would be the possible power state after this function return
>> - * successfully:
>> - * S1: UFS device in Active state with VCC rail ON
>> - * UniPro link in Active state
>> - * All the UFS/UniPro controller clocks are ON
>> - *
>> - * Returns 0 for success and non-zero for failure
>> + * 2. Turn ON VCC rail
>> */
>> int ufshcd_runtime_resume(struct ufs_hba *hba)
>> {
>> - int ret = 0;
>> ktime_t start = ktime_get();
>>
>> if (!hba)
>> @@ -9113,12 +9225,12 @@ int ufshcd_runtime_resume(struct ufs_hba *hba)
>> if (!hba->is_powered)
>> goto out;
>> else
>> - ret = ufshcd_resume(hba, UFS_RUNTIME_PM);
>> + ufshcd_resume(hba);
>> out:
>> - trace_ufshcd_runtime_resume(dev_name(hba->dev), ret,
>> + trace_ufshcd_runtime_resume(dev_name(hba->dev), 0,
>> ktime_to_us(ktime_sub(ktime_get(), start)),
>> hba->curr_dev_pwr_mode, hba->uic_link_state);
>> - return ret;
>> + return 0;
>> }
>> EXPORT_SYMBOL(ufshcd_runtime_resume);
>>
>> @@ -9132,14 +9244,13 @@ EXPORT_SYMBOL(ufshcd_runtime_idle);
>> * ufshcd_shutdown - shutdown routine
>> * @hba: per adapter instance
>> *
>> - * This function would power off both UFS device and UFS link.
>> + * This function would turn off both UFS device and UFS hba
>> + * regulators. It would also disable clocks.
>> *
>> * Returns 0 always to allow force shutdown even in case of errors.
>> */
>> int ufshcd_shutdown(struct ufs_hba *hba)
>> {
>> - int ret = 0;
>> -
>> down(&hba->host_sem);
>> hba->shutting_down = true;
>> up(&hba->host_sem);
>> @@ -9152,10 +9263,8 @@ int ufshcd_shutdown(struct ufs_hba *hba)
>>
>> pm_runtime_get_sync(hba->dev);
>>
>> - ret = ufshcd_suspend(hba, UFS_SHUTDOWN_PM);
>> + ufshcd_suspend(hba);
>> out:
>> - if (ret)
>> - dev_err(hba->dev, "%s failed, err %d\n", __func__, ret);
>> hba->is_powered = false;
>> /* allow force shutdown even in case of errors */
>> return 0;
>> @@ -9260,6 +9369,20 @@ static const struct blk_mq_ops ufshcd_tmf_ops = {
>> .queue_rq = ufshcd_queue_tmf,
>> };
>>
>> +static void ufshcd_scsi_sync_probe(struct work_struct *work)
>> +{
>> + struct ufs_hba *hba;
>> + struct scsi_device *sdev;
>> +
>> + hba = container_of(work, struct ufs_hba, sync_probe_work);
>> + wait_for_device_probe();
>> +
>> + shost_for_each_device(sdev, hba->host) {
>> + if (pm_runtime_enabled(&sdev->sdev_gendev))
>> + pm_runtime_allow(&sdev->sdev_gendev);
>> + }
>> +}
>> +
>> /**
>> * ufshcd_init - Driver initialization routine
>> * @hba: per-adapter instance
>> @@ -9456,6 +9579,8 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
>> */
>> ufshcd_set_ufs_dev_active(hba);
>>
>> + INIT_WORK(&hba->sync_probe_work, ufshcd_scsi_sync_probe);
>> + schedule_work(&hba->sync_probe_work);
>
> I think we still need to confirm whether or not this is needed, and whether
> it is something the UFS driver should be responsible for.
>
Ok, sure we can discuss more on this.
>> async_schedule(ufshcd_async_scan, hba);
>> ufs_sysfs_add_nodes(hba->dev);
>>
>> @@ -9477,15 +9602,162 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
>> }
>> EXPORT_SYMBOL_GPL(ufshcd_init);
>>
>> +void ufshcd_resume_complete(struct device *dev)
>> +{
>> + struct ufs_hba *hba = dev_get_drvdata(dev);
>> +
>> + pm_runtime_put_noidle(&hba->sdev_ufs_device->sdev_gendev);
>> +}
>> +EXPORT_SYMBOL_GPL(ufshcd_resume_complete);
>> +
>> +int ufshcd_suspend_prepare(struct device *dev)
>> +{
>> + struct ufs_hba *hba = dev_get_drvdata(dev);
>> +
>> + /*
>> + * SCSI assumes that runtime-pm and system-pm for scsi drivers
>> + * are same. And it doesn't wake up the device for system-suspend
>> + * if it's runtime suspended. But ufs doesn't follow that.
>> + * The rpm-lvl and spm-lvl can be different in ufs.
>> + * Force it to honor system-suspend.
>> + */
>> + scsi_autopm_get_device(hba->sdev_ufs_device);
>> + /* Refer ufshcd_resume_complete() */
>> + pm_runtime_get_noresume(&hba->sdev_ufs_device->sdev_gendev);
>> + scsi_autopm_put_device(hba->sdev_ufs_device);
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(ufshcd_suspend_prepare);
>> +
>> +#ifdef CONFIG_PM_SLEEP
>> +static int ufshcd_wl_poweroff(struct device *dev)
>> +{
>> + ufshcd_wl_shutdown(dev);
>> + return 0;
>> +}
>> +#endif
>> +
>> +static int ufshcd_wl_probe(struct device *dev)
>> +{
>> + return is_device_wlun(to_scsi_device(dev)) ? 0 : -ENODEV;
>> +}
>> +
>> +static int ufshcd_wl_remove(struct device *dev)
>> +{
>> + return 0;
>> +}
>> +
>> +static const struct dev_pm_ops ufshcd_wl_pm_ops = {
>> +#ifdef CONFIG_PM_SLEEP
>> + .suspend = ufshcd_wl_suspend,
>> + .resume = ufshcd_wl_resume,
>> + .freeze = ufshcd_wl_suspend,
>> + .thaw = ufshcd_wl_resume,
>> + .poweroff = ufshcd_wl_poweroff,
>> + .restore = ufshcd_wl_resume,
>> +#endif
>> + SET_RUNTIME_PM_OPS(ufshcd_wl_runtime_suspend, ufshcd_wl_runtime_resume, NULL)
>> +};
>> +
>> +/**
>> + * ufs_dev_wlun_template - describes ufs device wlun
>> + * ufs-device wlun - used to send pm commands
>> + * All luns are consumers of ufs-device wlun.
>> + *
>> + * Currently, no sd driver is present for wluns.
>> + * Hence the no specific pm operations are performed.
>> + * With ufs design, SSU should be sent to ufs-device wlun.
>> + * Hence register a scsi driver for ufs wluns only.
>> + */
>> +static struct scsi_driver ufs_dev_wlun_template = {
>> + .gendrv = {
>> + .name = "ufs_device_wlun",
>> + .owner = THIS_MODULE,
>> + .probe = ufshcd_wl_probe,
>> + .remove = ufshcd_wl_remove,
>> + .pm = &ufshcd_wl_pm_ops,
>> + .shutdown = ufshcd_wl_shutdown,
>> + },
>> +};
>> +
>> +static int ufshcd_rpmb_probe(struct device *dev)
>> +{
>> + return is_rpmb_wlun(to_scsi_device(dev)) ? 0 : -ENODEV;
>> +}
>> +
>> +static inline int ufshcd_clear_rpmb_uac(struct ufs_hba *hba)
>> +{
>> + int ret = 0;
>> +
>> + if (!hba->wlun_rpmb_clr_ua)
>> + return 0;
>> + ret = ufshcd_clear_ua_wlun(hba, UFS_UPIU_RPMB_WLUN);
>> + if (!ret)
>> + hba->wlun_rpmb_clr_ua = 0;
>> + return ret;
>> +}
>> +
>> +static int ufshcd_rpmb_runtime_resume(struct device *dev)
>> +{
>> + struct ufs_hba *hba = wlun_dev_to_hba(dev);
>> +
>> + if (hba->sdev_rpmb)
>> + return ufshcd_clear_rpmb_uac(hba);
>> + return 0;
>> +}
>> +
>> +static int ufshcd_rpmb_resume(struct device *dev)
>> +{
>> + struct ufs_hba *hba = wlun_dev_to_hba(dev);
>> +
>> + if (hba->sdev_rpmb && !pm_runtime_suspended(dev))
>> + return ufshcd_clear_rpmb_uac(hba);
>> + return 0;
>> +}
>> +
>> +static const struct dev_pm_ops ufs_rpmb_pm_ops = {
>> + SET_RUNTIME_PM_OPS(NULL, ufshcd_rpmb_runtime_resume, NULL)
>> + SET_SYSTEM_SLEEP_PM_OPS(NULL, ufshcd_rpmb_resume)
>> +};
>> +
>> +/**
>> + * Describes the ufs rpmb wlun.
>> + * Used only to send uac.
>> + */
>> +static struct scsi_driver ufs_rpmb_wlun_template = {
>> + .gendrv = {
>> + .name = "ufs_rpmb_wlun",
>> + .owner = THIS_MODULE,
>> + .probe = ufshcd_rpmb_probe,
>> + .pm = &ufs_rpmb_pm_ops,
>> + },
>> +};
>> +
>> static int __init ufshcd_core_init(void)
>> {
>> + int ret;
>> +
>> ufs_debugfs_init();
>> +
>> + ret = scsi_register_driver(&ufs_dev_wlun_template.gendrv);
>> + if (ret) {
>> + ufs_debugfs_eh_exit();
>> + return ret;
>> + }
>> + ret = scsi_register_driver(&ufs_rpmb_wlun_template.gendrv);
>> + if (ret) {
>> + ufs_debugfs_eh_exit();
>> + scsi_unregister_driver(&ufs_dev_wlun_template.gendrv);
>> + return ret;
>> + }
>> return 0;
>> }
>>
>> static void __exit ufshcd_core_exit(void)
>> {
>> ufs_debugfs_exit();
>> + scsi_unregister_driver(&ufs_dev_wlun_template.gendrv);
>> + scsi_unregister_driver(&ufs_rpmb_wlun_template.gendrv);
>> }
>>
>> module_init(ufshcd_core_init);
>> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
>> index ee61f82..c5f7335 100644
>> --- a/drivers/scsi/ufs/ufshcd.h
>> +++ b/drivers/scsi/ufs/ufshcd.h
>> @@ -72,6 +72,8 @@ enum ufs_event_type {
>> UFS_EVT_LINK_STARTUP_FAIL,
>> UFS_EVT_RESUME_ERR,
>> UFS_EVT_SUSPEND_ERR,
>> + UFS_EVT_WL_SUSP_ERR,
>> + UFS_EVT_WL_RES_ERR,
>>
>> /* abnormal events */
>> UFS_EVT_DEV_RESET,
>> @@ -804,6 +806,7 @@ struct ufs_hba {
>> struct list_head clk_list_head;
>>
>> bool wlun_dev_clr_ua;
>> + bool wlun_rpmb_clr_ua;
>>
>> /* Number of requests aborts */
>> int req_abort_count;
>> @@ -841,6 +844,8 @@ struct ufs_hba {
>> #ifdef CONFIG_DEBUG_FS
>> struct dentry *debugfs_root;
>> #endif
>> + struct work_struct sync_probe_work;
>> + u32 luns_avail;
>> };
>>
>> /* Returns true if clocks can be gated. Otherwise false */
>> @@ -1100,6 +1105,8 @@ int ufshcd_exec_raw_upiu_cmd(struct ufs_hba *hba,
>> enum query_opcode desc_op);
>>
>> int ufshcd_wb_ctrl(struct ufs_hba *hba, bool enable);
>> +int ufshcd_suspend_prepare(struct device *dev);
>> +void ufshcd_resume_complete(struct device *dev);
>>
>> /* Wrapper functions for safely calling variant operations */
>> static inline const char *ufshcd_get_var_name(struct ufs_hba *hba)
>> diff --git a/include/trace/events/ufs.h b/include/trace/events/ufs.h
>> index e151477..d9d233b 100644
>> --- a/include/trace/events/ufs.h
>> +++ b/include/trace/events/ufs.h
>> @@ -246,6 +246,26 @@ DEFINE_EVENT(ufshcd_template, ufshcd_init,
>> int dev_state, int link_state),
>> TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>>
>> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_suspend,
>> + TP_PROTO(const char *dev_name, int err, s64 usecs,
>> + int dev_state, int link_state),
>> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>> +
>> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_resume,
>> + TP_PROTO(const char *dev_name, int err, s64 usecs,
>> + int dev_state, int link_state),
>> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>> +
>> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_runtime_suspend,
>> + TP_PROTO(const char *dev_name, int err, s64 usecs,
>> + int dev_state, int link_state),
>> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>> +
>> +DEFINE_EVENT(ufshcd_template, ufshcd_wl_runtime_resume,
>> + TP_PROTO(const char *dev_name, int err, s64 usecs,
>> + int dev_state, int link_state),
>> + TP_ARGS(dev_name, err, usecs, dev_state, link_state));
>> +
>> TRACE_EVENT(ufshcd_command,
>> TP_PROTO(const char *dev_name, enum ufs_trace_str_t str_t,
>> unsigned int tag, u32 doorbell, int transfer_len, u32 intr,
>>
>
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
Linux Foundation Collaborative Project
Powered by blists - more mailing lists