| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <95b4be0b-c612-5b10-9266-f9e2ad24830c@ti.com>
Date: Fri, 19 Mar 2021 09:15:29 +0530
From: Aswath Govindraju <a-govindraju@...com>
To: Kishon Vijay Abraham I <kishon@...com>
CC: Vignesh Raghavendra <vigneshr@...com>,
Lokesh Vutla <lokeshvutla@...com>, Nishanth Menon <nm@...com>,
Tero Kristo <kristo@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher
speed modes and update delay select values for MMCSD subsystems
Hi Kishon,
On 18/03/21 8:45 pm, Kishon Vijay Abraham I wrote:
> Hi,
>
> On 10/03/21 9:49 pm, Aswath Govindraju wrote:
>> The following speed modes are now supported in J7200 SoC,
>> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
>> - UHS-I speed modes in MMCSD1 subsystem [1].
>>
>> Add support for UHS-I modes by adding voltage regulator device tree nodes
>> and corresponding pinmux details, to power cycle and voltage switch cards.
>> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
>> device tree nodes.
>>
>> Also update the delay values for various speed modes supported, based on
>> the latest J7200 datasheet[2]
>
> nit: Better to mention the datasheet version (as it's not latest anymore).
>>
>> [1] - section 12.3.6.1.1 MMCSD Features, in
>> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
>>
>> [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
> > Er.. this link is already broken.
>
Sorry, fixed this and added the version information for references in
the respin(v6) of this series.
Thank you for the comments.
Regards,
Aswath
> Thanks
> Kishon
>>
>> Signed-off-by: Aswath Govindraju <a-govindraju@...com>
>> ---
>> .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
>> 2 files changed, 54 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index b493f939b09a..6f90c3b1cf45 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -16,6 +16,29 @@
>> stdout-path = "serial2:115200n8";
>> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>> };
>> +
>> + vdd_mmc1: fixedregulator-sd {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vdd_mmc1";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + enable-active-high;
>> + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + vdd_sd_dv: gpio-regulator-vdd-sd-dv {
>> + compatible = "regulator-gpio";
>> + regulator-name = "vdd_sd_dv";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
>> + states = <1800000 0x0
>> + 3300000 0x1>;
>> + };
>> };
>>
>> &wkup_pmx0 {
>> @@ -45,6 +68,13 @@
>> };
>>
>> &main_pmx0 {
>> + main_i2c0_pins_default: main-i2c0-pins-default {
>> + pinctrl-single,pins = <
>> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
>> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>> + >;
>> + };
>> +
>> main_i2c1_pins_default: main-i2c1-pins-default {
>> pinctrl-single,pins = <
>> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
>> @@ -70,6 +100,12 @@
>> J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>> >;
>> };
>> +
>> + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
>> + pinctrl-single,pins = <
>> + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
>> + >;
>> + };
>> };
>>
>> &wkup_uart0 {
>> @@ -157,6 +193,10 @@
>> };
>>
>> &main_i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&main_i2c0_pins_default>;
>> + clock-frequency = <400000>;
>> +
>> exp1: gpio@20 {
>> compatible = "ti,tca6416";
>> reg = <0x20>;
>> @@ -206,6 +246,8 @@
>> /* SD card */
>> pinctrl-0 = <&main_mmc1_pins_default>;
>> pinctrl-names = "default";
>> + vmmc-supply = <&vdd_mmc1>;
>> + vqmmc-supply = <&vdd_sd_dv>;
>> ti,driver-strength-ohm = <50>;
>> disable-wp;
>> };
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> index e60650a62b14..f86c493a44f1 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> @@ -512,11 +512,16 @@
>> ti,otap-del-sel-mmc-hs = <0x0>;
>> ti,otap-del-sel-ddr52 = <0x6>;
>> ti,otap-del-sel-hs200 = <0x8>;
>> - ti,otap-del-sel-hs400 = <0x0>;
>> + ti,otap-del-sel-hs400 = <0x5>;
>> + ti,itap-del-sel-legacy = <0x10>;
>> + ti,itap-del-sel-mmc-hs = <0xa>;
>> ti,strobe-sel = <0x77>;
>> + ti,clkbuf-sel = <0x7>;
>> ti,trm-icp = <0x8>;
>> bus-width = <8>;
>> mmc-ddr-1_8v;
>> + mmc-hs200-1_8v;
>> + mmc-hs400-1_8v;
>> dma-coherent;
>> };
>>
>> @@ -534,7 +539,12 @@
>> ti,otap-del-sel-sdr50 = <0xc>;
>> ti,otap-del-sel-sdr104 = <0x5>;
>> ti,otap-del-sel-ddr50 = <0xc>;
>> - no-1-8-v;
>> + ti,itap-del-sel-legacy = <0x0>;
>> + ti,itap-del-sel-sd-hs = <0x0>;
>> + ti,itap-del-sel-sdr12 = <0x0>;
>> + ti,itap-del-sel-sdr25 = <0x0>;
>> + ti,clkbuf-sel = <0x7>;
>> + ti,trm-icp = <0x8>;
>> dma-coherent;
>> };
>>
>>
Powered by blists - more mailing lists