linux-kernel - Re: [PATCH v6 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <91af4ad6-507f-67a4-e85b-7c1ae52f0e64@ti.com>
Date:   Fri, 19 Mar 2021 09:57:52 +0530
From:   Kishon Vijay Abraham I <kishon@...com>
To:     Aswath Govindraju <a-govindraju@...com>
CC:     Vignesh Raghavendra <vigneshr@...com>,
        Lokesh Vutla <lokeshvutla@...com>, Nishanth Menon <nm@...com>,
        Tero Kristo <kristo@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v6 3/3] arm64: dts: ti: k3-j7200: Add support for higher
 speed modes and update delay select values for MMCSD subsystems

Hi Aswath,

On 19/03/21 9:14 am, Aswath Govindraju wrote:
> The following speed modes are now supported in J7200 SoC,
> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
> - UHS-I speed modes in MMCSD1 subsystem [1].
> 
> Add support for UHS-I modes by adding voltage regulator device tree nodes
> and corresponding pinmux details, to power cycle and voltage switch cards.
> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
> device tree nodes.
> 
> Also update the delay values for various speed modes supported, based on
> the revised january 2021 J7200 datasheet[2].
> 
> [1] - section 12.3.6.1.1 MMCSD Features, in
>       https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
>       (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
> 
> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
>       (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)

Thanks for fixing the link.

Reviewed-by: Kishon Vijay Abraham I <kishon@...com>
> 
> Signed-off-by: Aswath Govindraju <a-govindraju@...com>
> ---
>  .../dts/ti/k3-j7200-common-proc-board.dts     | 42 +++++++++++++++++++
>  arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 14 ++++++-
>  2 files changed, 54 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index b493f939b09a..6f90c3b1cf45 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -16,6 +16,29 @@
>  		stdout-path = "serial2:115200n8";
>  		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>  	};
> +
> +	vdd_mmc1: fixedregulator-sd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_mmc1";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		enable-active-high;
> +		gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
> +		compatible = "regulator-gpio";
> +		regulator-name = "vdd_sd_dv";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vdd_sd_dv_pins_default>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x0
> +			  3300000 0x1>;
> +	};
>  };
>  
>  &wkup_pmx0 {
> @@ -45,6 +68,13 @@
>  };
>  
>  &main_pmx0 {
> +	main_i2c0_pins_default: main-i2c0-pins-default {
> +		pinctrl-single,pins = <
> +			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> +			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> +		>;
> +	};
> +
>  	main_i2c1_pins_default: main-i2c1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -70,6 +100,12 @@
>  			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>  		>;
>  	};
> +
> +	vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
> +		pinctrl-single,pins = <
> +			J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
> +		>;
> +	};
>  };
>  
>  &wkup_uart0 {
> @@ -157,6 +193,10 @@
>  };
>  
>  &main_i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_i2c0_pins_default>;
> +	clock-frequency = <400000>;
> +
>  	exp1: gpio@20 {
>  		compatible = "ti,tca6416";
>  		reg = <0x20>;
> @@ -206,6 +246,8 @@
>  	/* SD card */
>  	pinctrl-0 = <&main_mmc1_pins_default>;
>  	pinctrl-names = "default";
> +	vmmc-supply = <&vdd_mmc1>;
> +	vqmmc-supply = <&vdd_sd_dv>;
>  	ti,driver-strength-ohm = <50>;
>  	disable-wp;
>  };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index e60650a62b14..f86c493a44f1 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -512,11 +512,16 @@
>  		ti,otap-del-sel-mmc-hs = <0x0>;
>  		ti,otap-del-sel-ddr52 = <0x6>;
>  		ti,otap-del-sel-hs200 = <0x8>;
> -		ti,otap-del-sel-hs400 = <0x0>;
> +		ti,otap-del-sel-hs400 = <0x5>;
> +		ti,itap-del-sel-legacy = <0x10>;
> +		ti,itap-del-sel-mmc-hs = <0xa>;
>  		ti,strobe-sel = <0x77>;
> +		ti,clkbuf-sel = <0x7>;
>  		ti,trm-icp = <0x8>;
>  		bus-width = <8>;
>  		mmc-ddr-1_8v;
> +		mmc-hs200-1_8v;
> +		mmc-hs400-1_8v;
>  		dma-coherent;
>  	};
>  
> @@ -534,7 +539,12 @@
>  		ti,otap-del-sel-sdr50 = <0xc>;
>  		ti,otap-del-sel-sdr104 = <0x5>;
>  		ti,otap-del-sel-ddr50 = <0xc>;
> -		no-1-8-v;
> +		ti,itap-del-sel-legacy = <0x0>;
> +		ti,itap-del-sel-sd-hs = <0x0>;
> +		ti,itap-del-sel-sdr12 = <0x0>;
> +		ti,itap-del-sel-sdr25 = <0x0>;
> +		ti,clkbuf-sel = <0x7>;
> +		ti,trm-icp = <0x8>;
>  		dma-coherent;
>  	};
>  
>