linux-kernel - Re: [PATCH v7 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <599d06e5-2b8f-011f-cf8d-3ccf34ee37b1@ti.com>
Date:   Tue, 23 Mar 2021 11:59:19 +0530
From:   Kishon Vijay Abraham I <kishon@...com>
To:     Aswath Govindraju <a-govindraju@...com>, Nishanth Menon <nm@...com>
CC:     Vignesh Raghavendra <vigneshr@...com>,
        Lokesh Vutla <lokeshvutla@...com>,
        Tero Kristo <kristo@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v7 3/3] arm64: dts: ti: k3-j7200: Add support for higher
 speed modes and update delay select values for MMCSD subsystems

Hi Aswath,

On 23/03/21 10:54 am, Aswath Govindraju wrote:
> Hi Nishanth,
> 
> On 22/03/21 9:05 pm, Nishanth Menon wrote:
>> On 18:42-20210322, Aswath Govindraju wrote:
>>> The following speed modes are now supported in J7200 SoC,
>>> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
>>> - UHS-I speed modes in MMCSD1 subsystem [1].
>>>
>>> Add support for UHS-I modes by adding voltage regulator device tree nodes
>>> and corresponding pinmux details, to power cycle and voltage switch cards.
>>> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
>>> device tree nodes.
>>>
>>> Also update the delay values for various speed modes supported, based on
>>> the revised january 2021 J7200 datasheet[2].
>>>
>>> [1] - section 12.3.6.1.1 MMCSD Features, in
>>>       https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
>>>       (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
>>>
>>> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
>>>       (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
>>>
>>> Signed-off-by: Aswath Govindraju <a-govindraju@...com>
>>> ---
>>>  .../dts/ti/k3-j7200-common-proc-board.dts     | 42 +++++++++++++++++++
>>>  arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 14 ++++++-
>>>  2 files changed, 54 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>> index b493f939b09a..de8c06bdc825 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>> @@ -16,6 +16,29 @@
>>>  		stdout-path = "serial2:115200n8";
>>>  		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>>>  	};
>>> +
>>> +	vdd_mmc1: fixedregulator-sd {
>>> +		compatible = "regulator-fixed";
>>> +		regulator-name = "vdd_mmc1";
>>> +		regulator-min-microvolt = <3300000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +		regulator-boot-on;
>>> +		enable-active-high;
>>> +		gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
>>
>> is that gpio ?
> 
> Yes, that is correct. I'll correct it in the respin
> 
>> I'd encourage to use vin-supply as well.
> 
> Will add this in respin.
> 
>>
>>> +	};
>>> +
>>> +	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
>> 	What does this drive? TLV71033 ?
> 
> Yes, this node models the TLV71033 voltage regulator that switches the
> MMC IO signal voltage level between 3.3V and 1.8V.

Nope. Unlike J721e SOM which uses TLV71033 for switching voltage, J7200
SOM directly uses GPIO input to PMIC to control the output voltage. So
this should model the gpio input to PMIC.

Thanks
Kishon