Message-ID: <CABkfQAGS24AM90veQhGA+=V4S50y7JwzqLMspMaEFptcYpmdMQ@mail.gmail.com>
Date:   Tue, 23 Mar 2021 15:16:10 +0100
From:   Adrien Grassein <adrien.grassein@...il.com>
To:     Robert Foss <robert.foss@...aro.org>
Cc:     David Airlie <airlied@...ux.ie>, Daniel Vetter <daniel@...ll.ch>,
        Andrzej Hajda <a.hajda@...sung.com>,
        Rob Herring <robh+dt@...nel.org>,
        Neil Armstrong <narmstrong@...libre.com>,
        Laurent Pinchart <Laurent.pinchart@...asonboard.com>,
        Jonas Karlman <jonas@...boo.se>,
        Jernej Skrabec <jernej.skrabec@...l.net>,
        dri-devel <dri-devel@...ts.freedesktop.org>,
        "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
        <devicetree@...r.kernel.org>,
        linux-kernel <linux-kernel@...r.kernel.org>,
        kernel test robot <lkp@...el.com>
Subject: Re: [PATCH v7 2/2] drm/bridge: Introduce LT8912B DSI to HDMI bridge

Le mar. 23 mars 2021 à 15:07, Robert Foss <robert.foss@...aro.org> a écrit :
>
> > > > >
> > > > > > +static enum drm_connector_status lt8912_check_cable_status(struct lt8912 *lt)
> > > > > > +{
> > > > > > +       int ret;
> > > > > > +       unsigned int reg_val;
> > > > > > +
> > > > > > +       ret = regmap_read(lt->regmap[I2C_MAIN], 0xC1, &reg_val);
> > > > > > +       if (ret)
> > > > > > +               return connector_status_unknown;
> > > > > > +
> > > > > > +       if (reg_val & BIT(7))
> > > > > > +               return connector_status_connected;
> > > > >
> > > > > Register 0xc0 & BIT(7) - HPD signal after debounce
> > > > > Register 0xc0 & BIT(6) - HPD signal for TX HPD pad
> > > >
> > > > So, if I understand well, I need to write 0xc0 & BIT(6) with 1 to
> > > > enable the HPD pin.
> > >
> > > Ah, sorry about being a bit terse.
> > >
> > > Both bit 6 & 7 are read only, and are probably best read after an IRQ.
> >
> > In my case, IRQ is not triggered at all.
>
> Are you saying that pin 63 never is high, or that an irq/isr routine
> isn't getting executed?
>
> > When reading the value of the HPD pin, I always get 1 (and no
> > transition occurs when plugging / unplugging a cable).
> > The HPD IRQ is done on the HDMI connector driver [5].
> > I think a register configuration should be done to enable the IRQ pin
> > or maybe there is a nug in electronics.
>
> After looking at the documentation a bit more, I think we can ignore
> pin63 and instead have a look at pin14. It is the HDMI TX HPD Control
> pin. It has a 100k pull-down, so it should be active high.

pin63 is always active high.
pin14 is connected to the HDMI logic (pin 19 of the HDMI connector)
with a 100k pull-down.

>
> I also found some different I2C addresses than what you've used, I
> assume the device is available on both addresses.
>
> Chip control registers, address:0x90
> CEC control registers, address 0x92
>
Strange, configuration seems to be working well with the address used
in my driver.

> > The HPD pin is linked to a 2.2k pullup resistor (maybe it's wrong)
>
> The datasheet isn't entirely clear about if pin14 has an internal 100k
> pull-down, or if they recommend adding a 100k pull-down.
>
> But this does seem like an issue.

pin14 can't be used directly. I guess it's used by the internal logic
of the chip to generate the HPD (pin63) signal.
>
> >
> > >
> > > > >
> > > > > > +
> > > > > > +static int lt8912_probe(struct i2c_client *client,
> > > > > > +        const struct i2c_device_id *id)
> > > > > > +{
> > > > > > +       static struct lt8912 *lt;
> > > > > > +       int ret = 0;
> > > > > > +       struct device *dev = &client->dev;
> > > > > > +
> > > > > > +       lt = devm_kzalloc(dev, sizeof(struct lt8912), GFP_KERNEL);
> > > > > > +       if (!lt)
> > > > > > +               return -ENOMEM;
> > > > > > +
> > > > > > +       lt->dev = dev;
> > > > > > +       lt->i2c_client[0] = client;
> > > > > > +       lt->cable_status = connector_status_unknown;
> > > > > > +       lt->workq = create_workqueue("lt8912_workq");
> > > > >
> > > > > Looking at [1] and maybe even better [2], I think this polling
> > > > > approach is the wrong way to go. And with access to documentation, I
> > > > > think we should be able to sort this out.
> > > >
> > > > I neither like the polling approach too. I did it to go on this issue.
> > > > I will totally remove it once the HPD issue will be resolved.
> > > > >
> > > > > Using the irq driver approach requires the interrupt pin to be
> > > > > configured. Pin 63 of the lt8912b is the IRQ output pin.
> > > > >
> > > > > In order to trigger interrupts based on it, the dt-binding would need
> > > > > to be updated[3][4] as well as whichever DTS you're using.
> > > > >
> > > >
> > > > The IRQ part is working well in my DTB. It test it by adding some
> > > > electronics to emulate the HPD pin on the GPIO expander where the HPD
> > > > pin is linked.
> > >
> > > Looking at the dt-binding patch, it does not seem to list any
> > > interrupts. So that should be added. I think the irq support from [3]
> > > & [4] can be pretty much copied.
> > >
> > > Then we can come back and replace the polling code with the IRQ driven
> > > code from [2].
> >
> > My board uses a "max7323" GPIO expander and the HPD pin is linked to it.
> > I test this GPIO expander by soldering a pull up resistor and an
> > interrupt on it and an interrupt was correctly triggered in both
> > max7323 driver and hdmi-connector;
> > So I guess that my DTB configuration is correct.
> > I made my DBT configuration available:
> >   - hdmi-connector node: [6]
> >   - lt8912b node: |7]
> >   - max7323 node: [8].
>
> Looking at [7] I think that you would want to add something like:
>
> hdmi-bridge@48 {
>         interrupts-extended = <&max7323 $LT8912B_PIN_14 IRQ_TYPE_EDGE_RISING>;
> }
>
> And of course add the corresponding parts from [2] and [3].
>
> >
> >
> > >
> > > >
> > > > >
> > > > > [1] https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/bridge/analogix/anx7625.c#L1751
> > > > >
> > > > > [2] https://github.com/torvalds/linux/blob/v5.11/drivers/gpu/drm/bridge/lontium-lt9611.c#L1160
> > > > >
> > > > > [3] https://github.com/torvalds/linux/blob/v5.11/Documentation/devicetree/bindings/display/bridge/lontium,lt9611.yaml#L27
> > > > >
> > > > > [4] https://github.com/torvalds/linux/blob/v5.11/Documentation/devicetree/bindings/display/bridge/lontium,lt9611.yaml#L144
> >
> > [5] https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/bridge/display-connector.c#L199
> > [6] https://github.com/grassead/linux-next/blob/master/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts#L37
> > [7] https://github.com/grassead/linux-next/blob/master/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts#L249
> > [8] https://github.com/grassead/linux-next/blob/master/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts#L291
> >
> >
> > Thanks,

Maybe the conclusion is that we cannot have the HPD working.

Thanks,

Powered by blists - more mailing lists