| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210415105010.569620-10-claudiu.beznea@microchip.com>
Date: Thu, 15 Apr 2021 13:49:55 +0300
From: Claudiu Beznea <claudiu.beznea@...rochip.com>
To: <nicolas.ferre@...rochip.com>, <alexandre.belloni@...tlin.com>,
<ludovic.desroches@...rochip.com>, <robh+dt@...nel.org>,
<linux@...linux.org.uk>
CC: <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Claudiu Beznea <claudiu.beznea@...rochip.com>
Subject: [PATCH v3 09/24] ARM: at91: pm: add support for waiting MCK1..4
SAMA7G5 has 5 master clocks 0..4. MCK0 is controlled differently than
MCK 1..4. MCK 1..4 should also be saved/restored in the last phase of
suspend/resume. Thus, adapt wait_mckrdy to support also MCK1..4.
Signed-off-by: Claudiu Beznea <claudiu.beznea@...rochip.com>
---
arch/arm/mach-at91/pm_suspend.S | 48 ++++++++++++++++++++++++---------
1 file changed, 35 insertions(+), 13 deletions(-)
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index 1f63bbfad728..7669b32d5257 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -22,11 +22,23 @@ tmp3 .req r6
/*
* Wait until master clock is ready (after switching master clock source)
+ *
+ * @r_mckid: register holding master clock identifier
+ *
+ * Side effects: overwrites r7, r8
*/
- .macro wait_mckrdy
-1: ldr tmp1, [pmc, #AT91_PMC_SR]
- tst tmp1, #AT91_PMC_MCKRDY
- beq 1b
+ .macro wait_mckrdy r_mckid
+#ifdef CONFIG_SOC_SAMA7
+ cmp \r_mckid, #0
+ beq 1f
+ mov r7, #AT91_PMC_MCKXRDY
+ b 2f
+#endif
+1: mov r7, #AT91_PMC_MCKRDY
+2: ldr r8, [pmc, #AT91_PMC_SR]
+ and r8, r7
+ cmp r8, r7
+ bne 2b
.endm
/*
@@ -231,7 +243,9 @@ sr_dis_exit:
bic tmp1, tmp1, #AT91_PMC_PRES
orr tmp1, tmp1, #AT91_PMC_PRES_64
str tmp1, [pmc, tmp3]
- wait_mckrdy
+
+ mov tmp3, #0
+ wait_mckrdy tmp3
b 1f
0:
@@ -267,10 +281,13 @@ sr_dis_exit:
bne 5f
/* Set lowest prescaler for fast resume. */
+ ldr tmp3, .mckr_offset
ldr tmp1, [pmc, tmp3]
bic tmp1, tmp1, #AT91_PMC_PRES
str tmp1, [pmc, tmp3]
- wait_mckrdy
+
+ mov tmp3, #0
+ wait_mckrdy tmp3
b 6f
5: /* Restore RC oscillator state */
@@ -307,6 +324,7 @@ sr_dis_exit:
.macro at91_pm_ulp1_mode
ldr pmc, .pmc_base
ldr tmp2, .mckr_offset
+ mov tmp3, #0
/* Save RC oscillator state and check if it is enabled. */
ldr tmp1, [pmc, #AT91_PMC_SR]
@@ -348,7 +366,7 @@ sr_dis_exit:
orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
str tmp1, [pmc, tmp2]
- wait_mckrdy
+ wait_mckrdy tmp3
/* Enter the ULP1 mode by set WAITMODE bit in CKGR_MOR */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
@@ -361,7 +379,7 @@ sr_dis_exit:
nop
nop
- wait_mckrdy
+ wait_mckrdy tmp3
/* Enable the crystal oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
@@ -377,7 +395,7 @@ sr_dis_exit:
bic tmp1, tmp1, #AT91_PMC_CSS
str tmp1, [pmc, tmp2]
- wait_mckrdy
+ wait_mckrdy tmp3
/* Switch main clock source to crystal oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
@@ -394,7 +412,7 @@ sr_dis_exit:
orr tmp1, tmp1, #AT91_PMC_CSS_MAIN
str tmp1, [pmc, tmp2]
- wait_mckrdy
+ wait_mckrdy tmp3
/* Restore RC oscillator state */
ldr tmp1, .saved_osc_status
@@ -573,10 +591,12 @@ sr_dis_exit:
save_mck:
str tmp1, [pmc, tmp2]
- wait_mckrdy
+ mov tmp3, #0
+ wait_mckrdy tmp3
at91_plla_disable
+ ldr tmp3, .pm_mode
cmp tmp3, #AT91_PM_ULP1
beq ulp1_mode
@@ -599,7 +619,8 @@ ulp_exit:
ldr tmp2, .saved_mckr
str tmp2, [pmc, tmp1]
- wait_mckrdy
+ mov tmp3, #0
+ wait_mckrdy tmp3
.endm
@@ -611,7 +632,8 @@ ulp_exit:
bic tmp1, tmp1, #AT91_PMC_CSS
str tmp1, [pmc, tmp2]
- wait_mckrdy
+ mov tmp3, #0
+ wait_mckrdy tmp3
/*BUMEN*/
ldr r0, .sfrbu
--
2.25.1
Powered by blists - more mailing lists