| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210422103037.GA239298@localhost>
Date: Thu, 22 Apr 2021 16:00:37 +0530
From: Deepak R Varma <drv@...lo.com>
To: Mauro Carvalho Chehab <mchehab@...nel.org>,
Sakari Ailus <sakari.ailus@...ux.intel.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>
Cc: linux-media@...r.kernel.org, linux-staging@...ts.linux.dev,
linux-kernel@...r.kernel.org, mh12gx2825@...il.com, drv@...lo.com
Subject: [PATCH] staging: media: atomisp: replace pr_info() by dev_info()
It is recommended to use driver model diagnostic macros dev_*() instead
of pr_*() since the former ensures that the log messages are always
associated with the corresponding device and driver.
Suggested-by: Fabio Aiuto <fabioaiuto83@...il.com>
Signed-off-by: Deepak R Varma <drv@...lo.com>
---
Note: There are few more pr_into() calls that I have not replaced since
they are very basic (entry and exit) and temporary. They can be removed
if the APIs are fully tested. See this example:
pr_info("%s S\n", __func__);
Let me know if I should remove them and resubmit this patch.
.../media/atomisp/i2c/atomisp-gc0310.c | 30 +++++++++----------
1 file changed, 15 insertions(+), 15 deletions(-)
diff --git a/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c b/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
index 7e4e123fdb52..27153ec6f65e 100644
--- a/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
+++ b/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
@@ -300,7 +300,7 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
/* pixel clock calculattion */
dev->vt_pix_clk_freq_mhz = 14400000; // 16.8MHz
buf->vt_pix_clk_freq_mhz = dev->vt_pix_clk_freq_mhz;
- pr_info("vt_pix_clk_freq_mhz=%d\n", buf->vt_pix_clk_freq_mhz);
+ dev_info(&client->dev, "vt_pix_clk_freq_mhz=%d\n", buf->vt_pix_clk_freq_mhz);
/* get integration time */
buf->coarse_integration_time_min = GC0310_COARSE_INTG_TIME_MIN;
@@ -326,7 +326,7 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
if (ret)
return ret;
buf->crop_horizontal_start = val | (reg_val & 0xFF);
- pr_info("crop_horizontal_start=%d\n", buf->crop_horizontal_start);
+ dev_info(&client->dev, "crop_horizontal_start=%d\n", buf->crop_horizontal_start);
/* Getting crop_vertical_start */
ret = gc0310_read_reg(client, GC0310_8BIT,
@@ -339,7 +339,7 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
if (ret)
return ret;
buf->crop_vertical_start = val | (reg_val & 0xFF);
- pr_info("crop_vertical_start=%d\n", buf->crop_vertical_start);
+ dev_info(&client->dev, "crop_vertical_start=%d\n", buf->crop_vertical_start);
/* Getting output_width */
ret = gc0310_read_reg(client, GC0310_8BIT,
@@ -352,7 +352,7 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
if (ret)
return ret;
buf->output_width = val | (reg_val & 0xFF);
- pr_info("output_width=%d\n", buf->output_width);
+ dev_info(&client->dev, "output_width=%d\n", buf->output_width);
/* Getting output_height */
ret = gc0310_read_reg(client, GC0310_8BIT,
@@ -365,12 +365,12 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
if (ret)
return ret;
buf->output_height = val | (reg_val & 0xFF);
- pr_info("output_height=%d\n", buf->output_height);
+ dev_info(&client->dev, "output_height=%d\n", buf->output_height);
buf->crop_horizontal_end = buf->crop_horizontal_start + buf->output_width - 1;
buf->crop_vertical_end = buf->crop_vertical_start + buf->output_height - 1;
- pr_info("crop_horizontal_end=%d\n", buf->crop_horizontal_end);
- pr_info("crop_vertical_end=%d\n", buf->crop_vertical_end);
+ dev_info(&client->dev, "crop_horizontal_end=%d\n", buf->crop_horizontal_end);
+ dev_info(&client->dev, "crop_vertical_end=%d\n", buf->crop_vertical_end);
/* Getting line_length_pck */
ret = gc0310_read_reg(client, GC0310_8BIT,
@@ -389,8 +389,8 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
return ret;
sh_delay = reg_val;
buf->line_length_pck = buf->output_width + hori_blanking + sh_delay + 4;
- pr_info("hori_blanking=%d sh_delay=%d line_length_pck=%d\n", hori_blanking,
- sh_delay, buf->line_length_pck);
+ dev_info(&client->dev, "hori_blanking=%d sh_delay=%d line_length_pck=%d\n", hori_blanking,
+ sh_delay, buf->line_length_pck);
/* Getting frame_length_lines */
ret = gc0310_read_reg(client, GC0310_8BIT,
@@ -404,8 +404,8 @@ static int gc0310_get_intg_factor(struct i2c_client *client,
return ret;
vert_blanking = val | (reg_val & 0xFF);
buf->frame_length_lines = buf->output_height + vert_blanking;
- pr_info("vert_blanking=%d frame_length_lines=%d\n", vert_blanking,
- buf->frame_length_lines);
+ dev_info(&client->dev, "vert_blanking=%d frame_length_lines=%d\n", vert_blanking,
+ buf->frame_length_lines);
buf->binning_factor_x = res->bin_factor_x ?
res->bin_factor_x : 1;
@@ -434,7 +434,7 @@ static int gc0310_set_gain(struct v4l2_subdev *sd, int gain)
dgain = gain / 2;
}
- pr_info("gain=0x%x again=0x%x dgain=0x%x\n", gain, again, dgain);
+ dev_info(&client->dev, "gain=0x%x again=0x%x dgain=0x%x\n", gain, again, dgain);
/* set analog gain */
ret = gc0310_write_reg(client, GC0310_8BIT,
@@ -458,7 +458,7 @@ static int __gc0310_set_exposure(struct v4l2_subdev *sd, int coarse_itg,
struct i2c_client *client = v4l2_get_subdevdata(sd);
int ret;
- pr_info("coarse_itg=%d gain=%d digitgain=%d\n", coarse_itg, gain, digitgain);
+ dev_info(&client->dev, "coarse_itg=%d gain=%d digitgain=%d\n", coarse_itg, gain, digitgain);
/* set exposure */
ret = gc0310_write_reg(client, GC0310_8BIT,
@@ -1085,7 +1085,7 @@ static int gc0310_detect(struct i2c_client *client)
return -ENODEV;
}
id = ((((u16)high) << 8) | (u16)low);
- pr_info("sensor ID = 0x%x\n", id);
+ dev_info(&client->dev, "sensor ID = 0x%x\n", id);
if (id != GC0310_ID) {
dev_err(&client->dev, "sensor ID error, read id = 0x%x, target id = 0x%x\n", id,
@@ -1106,7 +1106,7 @@ static int gc0310_s_stream(struct v4l2_subdev *sd, int enable)
struct i2c_client *client = v4l2_get_subdevdata(sd);
int ret;
- pr_info("%s S enable=%d\n", __func__, enable);
+ dev_info(&client->dev, "%s S enable=%d\n", __func__, enable);
mutex_lock(&dev->input_lock);
if (enable) {
--
2.25.1
Powered by blists - more mailing lists