linux-kernel - Re: [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <e877868f-c5b4-ae8b-9871-c0633781e8e4@baylibre.com>
Date:   Fri, 30 Apr 2021 10:35:48 +0200
From:   Neil Armstrong <narmstrong@...libre.com>
To:     Liu Ying <victor.liu@....com>, dri-devel@...ts.freedesktop.org
Cc:     jernej.skrabec@...l.net, jonas@...boo.se, airlied@...ux.ie,
        agx@...xcpu.org, linux-kernel@...r.kernel.org,
        robert.foss@...aro.org, a.hajda@...sung.com,
        Laurent.pinchart@...asonboard.com, robert.chiras@....com,
        linux-imx@....com
Subject: Re: [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and
 PHY ready in ->mode_set()

On 23/04/2021 11:26, Liu Ying wrote:
> Hi,
> 
> This series aims to make the nwl-dsi bridge be able to connect with
> more MIPI DSI panels.  Some MIPI DSI panel drivers like 'raydium,rm68200'
> send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
> requires the MIPI DSI controller and PHY to be ready beforehand.
> However, the existing nwl-dsi driver gets the MIPI DSI controller and
> PHY ready in bridge_funcs->pre_enable(), which happens after the
> panel_funcs->prepare().  So, this series shifts the bridge operation
> ealier from bridge_funcs->pre_enable() to bridge_funcs->mode_set().
> 
> Patch 3/3 does the essential bridge operation shift.
> 
> Patch 1/3 and 2/3 are split from the original single patch in v2 and
> are needed by patch 3/3.  This split-up helps clarify changes better.
> The split-up is done in this way:
> 
> 1) Patch 1/3 forces a full modeset when crtc_state->active is changed to
>    be true(which implies only connector's DPMS is brought out of "Off"
>    status, though not necessarily).  This makes sure ->mode_set() and
>    ->atomic_disable() will be called in pairs.
> 2) Patch 2/3 removes a check on unchanged HS clock rate from ->mode_set(),
>    to make sure MIPI DSI controller and PHY are brought up and taken down
>    in pairs.
> 3) Patch 3/3 shifts the bridge operation as the last step.
> 
> 
> v2->v3:
> * Split the single patch in v2 into 3 patches. (Neil)
> 
> v1->v2:
> * Fix a typo in commit message - s/unchange/unchanged/
> 
> 
> Liu Ying (3):
>   drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is
>     changed to be true
>   drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from
>     ->mode_set()
>   drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in
>     ->mode_set()
> 
>  drivers/gpu/drm/bridge/nwl-dsi.c | 86 +++++++++++++++++---------------
>  1 file changed, 46 insertions(+), 40 deletions(-)
> 

Applying to drm-misc-next

Thanks,
Neil