| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1621332225-31918-2-git-send-email-mkrishn@codeaurora.org>
Date: Tue, 18 May 2021 15:33:43 +0530
From: Krishna Manikandan <mkrishn@...eaurora.org>
To: dri-devel@...ts.freedesktop.org, linux-arm-msm@...r.kernel.org,
freedreno@...ts.freedesktop.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Cc: Krishna Manikandan <mkrishn@...eaurora.org>,
kalyan_t@...eaurora.org, tanmay@...eaurora.org,
abhinavk@...eaurora.org, robdclark@...il.com, swboyd@...omium.org,
bjorn.andersson@...aro.org, vinod.koul@...aro.org,
dianders@...omium.org, khsieh@...eaurora.org, robh+dt@...nel.org,
sean@...rly.run, robh@...nel.org
Subject: [PATCH v16 2/4] dt-bindings: msm: dsi: add yaml schemas for DSI bindings
Add YAML schema for the device tree bindings for DSI
Signed-off-by: Krishna Manikandan <mkrishn@...eaurora.org>
Changes in v1:
- Separate dsi controller bindings to a separate patch (Stephen Boyd)
- Merge dsi-common-controller.yaml and dsi-controller-main.yaml to
a single file (Stephen Boyd)
- Drop supply entries and definitions from properties (Stephen Boyd)
- Modify phy-names property for dsi controller (Stephen Boyd)
- Remove boolean from description (Stephen Boyd)
- Drop pinctrl properties as they are standard entries (Stephen Boyd)
- Modify the description for ports property and keep the reference
to the generic binding where this is defined (Stephen Boyd)
- Add description to clock names (Stephen Boyd)
- Correct the indendation (Stephen Boyd)
- Drop the label for display dt nodes and correct the node
name (Stephen Boyd)
Changes in v2:
- Drop maxItems for clock (Stephen Boyd)
- Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream
dt file (Stephen Boyd)
- Keep child node directly under soc node (Stephen Boyd)
- Drop qcom,sync-dual-dsi as it is not used in upstream dt
Changes in v3:
- Add description for register property (Stephen Boyd)
Changes in v4:
- Add maxItems for phys property (Stephen Boyd)
- Add maxItems for reg property (Stephen Boyd)
- Add reference for data-lanes property (Stephen Boyd)
- Remove soc from example (Stephen Boyd)
Changes in v5:
- Modify title and description (Stephen Boyd)
- Add required properties for ports node (Stephen Boyd)
- Add data-lanes in the example (Stephen Boyd)
- Drop qcom,master-dsi property (Stephen Boyd)
Changes in v6:
- Add required properties for port@0, port@1 and corresponding
endpoints (Stephen Boyd)
- Add address-cells and size-cells for ports (Stephen Boyd)
- Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)
Changes in v7:
- Add reference for ports and data-lanes (Rob Herring)
- Add maxItems and minItems for data-lanes (Rob Herring)
---
.../bindings/display/msm/dsi-controller-main.yaml | 209 +++++++++++++++++
.../devicetree/bindings/display/msm/dsi.txt | 249 ---------------------
2 files changed, 209 insertions(+), 249 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
new file mode 100644
index 0000000..80f5218
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml
@@ -0,0 +1,209 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display DSI controller
+
+maintainers:
+ - Krishna Manikandan <mkrishn@...eaurora.org>
+
+allOf:
+ - $ref: "../dsi-controller.yaml#"
+
+properties:
+ compatible:
+ items:
+ - const: qcom,mdss-dsi-ctrl
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: dsi_ctrl
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display byte clock
+ - description: Display byte interface clock
+ - description: Display pixel clock
+ - description: Display escape clock
+ - description: Display AHB clock
+ - description: Display AXI clock
+
+ clock-names:
+ items:
+ - const: byte
+ - const: byte_intf
+ - const: pixel
+ - const: core
+ - const: iface
+ - const: bus
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ const: dsi
+
+ "#address-cells": true
+
+ "#size-cells": true
+
+ syscon-sfpb:
+ description: A phandle to mmss_sfpb syscon node (only for DSIv2).
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ qcom,dual-dsi-mode:
+ type: boolean
+ description: |
+ Indicates if the DSI controller is driving a panel which needs
+ 2 DSI links.
+
+ power-domains:
+ maxItems: 1
+
+ operating-points-v2: true
+
+ ports:
+ $ref: "/schemas/graph.yaml#/properties/ports"
+ description: |
+ Contains DSI controller input and output ports as children, each
+ containing one endpoint subnode.
+
+ properties:
+ port@0:
+ $ref: "/schemas/graph.yaml#/properties/port"
+ description: |
+ Input endpoints of the controller.
+
+ properties:
+ reg:
+ const: 0
+
+ endpoint:
+ type: object
+ properties:
+ remote-endpoint: true
+ data-lanes:
+ $ref: "../../media/video-interfaces.yaml"
+ description: |
+ This describes how the physical DSI data lanes are mapped
+ to the logical lanes on the given platform. The value contained in
+ index n describes what physical lane is mapped to the logical lane n
+ (DATAn, where n lies between 0 and 3). The clock lane position is fixed
+ and can't be changed. Hence, they aren't a part of the DT bindings.
+ maxItems: 4
+ minItems: 4
+ items:
+ enum: [ 0, 1, 2, 3 ]
+
+ required:
+ - reg
+ - endpoint
+
+ port@1:
+ $ref: "/schemas/graph.yaml#/properties/port"
+ description: |
+ Output endpoints of the controller.
+ properties:
+ reg:
+ const: 1
+
+ endpoint:
+ type: object
+ properties:
+ remote-endpoint: true
+ data-lanes:
+ maxItems: 4
+ minItems: 4
+ items:
+ enum: [ 0, 1, 2, 3 ]
+
+ required:
+ - reg
+ - endpoint
+
+ required:
+ - port@0
+ - port@1
+ - "#address-cells"
+ - "#size-cells"
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - interrupts
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+ - power-domains
+ - operating-points-v2
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ dsi@...4000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0x0ae94000 0x400>;
+ reg-names = "dsi_ctrl";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi";
+
+ power-domains = <&rpmhpd SC7180_CX>;
+ operating-points-v2 = <&dsi_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ remote-endpoint = <&sn65dsi86_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
deleted file mode 100644
index b9a64d3..0000000
--- a/Documentation/devicetree/bindings/display/msm/dsi.txt
+++ /dev/null
@@ -1,249 +0,0 @@
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
- * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
- * "dsi_ctrl"
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks.
-- clock-names: the following clocks are required:
- * "mdp_core"
- * "iface"
- * "bus"
- * "core_mmss"
- * "byte"
- * "pixel"
- * "core"
- For DSIv2, we need an additional clock:
- * "src"
- For DSI6G v2.0 onwards, we need also need the clock:
- * "byte_intf"
-- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
-- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
- by a DSI PHY block. See [1] for details on clock bindings.
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- phys: phandle to DSI PHY device node
-- phy-names: the name of the corresponding PHY device
-- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
-- ports: Contains 2 DSI controller ports as child nodes. Each port contains
- an endpoint subnode as defined in [2] and [3].
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
- See files in [4] for each supported panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
- driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
- the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
- driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- ports: contains DSI controller input and output ports as children, each
- containing one endpoint subnode.
-
- DSI Endpoint properties:
- - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
- input endpoint. For port@1, set to the MDP interface output. See [2] for
- device graph info.
-
- - data-lanes: this describes how the physical DSI data lanes are mapped
- to the logical lanes on the given platform. The value contained in
- index n describes what physical lane is mapped to the logical lane n
- (DATAn, where n lies between 0 and 3). The clock lane position is fixed
- and can't be changed. Hence, they aren't a part of the DT bindings. See
- [3] for more info on the data-lanes property.
-
- For example:
-
- data-lanes = <3 0 1 2>;
-
- The above mapping describes that the logical data lane DATA0 is mapped to
- the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
- to phys DATA1 and logic DATA3 to phys DATA2.
-
- There are only a limited number of physical to logical mappings possible:
- <0 1 2 3>
- <1 2 3 0>
- <2 3 0 1>
- <3 0 1 2>
- <0 3 2 1>
- <1 0 3 2>
- <2 1 0 3>
- <3 2 1 0>
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
- * "qcom,dsi-phy-28nm-hpm"
- * "qcom,dsi-phy-28nm-lp"
- * "qcom,dsi-phy-20nm"
- * "qcom,dsi-phy-28nm-8960"
- * "qcom,dsi-phy-14nm"
- * "qcom,dsi-phy-14nm-660"
- * "qcom,dsi-phy-10nm"
- * "qcom,dsi-phy-10nm-8998"
- * "qcom,dsi-phy-7nm"
- * "qcom,dsi-phy-7nm-8150"
-- reg: Physical base address and length of the registers of PLL, PHY. Some
- revisions require the PHY regulator base address, whereas others require the
- PHY lane base address. See below for each PHY revision.
-- reg-names: The names of register regions. The following regions are required:
- For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_regulator"
- For DSI 14nm, 10nm and 7nm PHYs:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_lane"
-- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
- 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: Phandles to device clocks. See [1] for details on clock bindings.
-- clock-names: the following clocks are required:
- * "iface"
- * "ref" (only required for new DTS files/entries)
- For 28nm HPM/LP, 28nm 8960 PHYs:
-- vddio-supply: phandle to vdd-io regulator device node
- For 20nm PHY:
-- vddio-supply: phandle to vdd-io regulator device node
-- vcca-supply: phandle to vcca regulator device node
- For 14nm PHY:
-- vcca-supply: phandle to vcca regulator device node
- For 10nm and 7nm PHY:
-- vdds-supply: phandle to vdds regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
- regulator is wanted.
-- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
- panels in microseconds. Driver uses this number to adjust
- the clock rate according to the expected transfer time.
- Increasing this value would slow down the mdp processing
- and can result in slower performance.
- Decreasing this value can speed up the mdp processing,
- but this can also impact power consumption.
- As a rule this time should not be higher than the time
- that would be expected with the processing at the
- dsi link rate since anyways this would be the maximum
- transfer time that could be achieved.
- If ping pong split is enabled, this time should not be higher
- than two times the dsi link rate time.
- If the property is not specified, then the default value is 14000 us.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/graph.txt
-[3] Documentation/devicetree/bindings/media/video-interfaces.txt
-[4] Documentation/devicetree/bindings/display/panel/
-
-Example:
- dsi0: dsi@...22800 {
- compatible = "qcom,mdss-dsi-ctrl";
- qcom,dsi-host-index = <0>;
- interrupt-parent = <&mdp>;
- interrupts = <4 0>;
- reg-names = "dsi_ctrl";
- reg = <0xfd922800 0x200>;
- power-domains = <&mmcc MDSS_GDSC>;
- clock-names =
- "bus",
- "byte",
- "core",
- "core_mmss",
- "iface",
- "mdp_core",
- "pixel";
- clocks =
- <&mmcc MDSS_AXI_CLK>,
- <&mmcc MDSS_BYTE0_CLK>,
- <&mmcc MDSS_ESC0_CLK>,
- <&mmcc MMSS_MISC_AHB_CLK>,
- <&mmcc MDSS_AHB_CLK>,
- <&mmcc MDSS_MDP_CLK>,
- <&mmcc MDSS_PCLK0_CLK>;
-
- assigned-clocks =
- <&mmcc BYTE0_CLK_SRC>,
- <&mmcc PCLK0_CLK_SRC>;
- assigned-clock-parents =
- <&dsi_phy0 0>,
- <&dsi_phy0 1>;
-
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
-
- phys = <&dsi_phy0>;
- phy-names ="dsi-phy";
-
- qcom,dual-dsi-mode;
- qcom,master-dsi;
- qcom,sync-dual-dsi;
-
- qcom,mdss-mdp-transfer-time-us = <12000>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&dsi_active>;
- pinctrl-1 = <&dsi_suspend>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dsi0_in: endpoint {
- remote-endpoint = <&mdp_intf1_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- dsi0_out: endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
-
- panel: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
- link2 = <&secondary>;
-
- power-supply = <...>;
- backlight = <...>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
- };
-
- dsi_phy0: dsi-phy@...22a00 {
- compatible = "qcom,dsi-phy-28nm-hpm";
- qcom,dsi-phy-index = <0>;
- reg-names =
- "dsi_pll",
- "dsi_phy",
- "dsi_phy_regulator";
- reg = <0xfd922a00 0xd4>,
- <0xfd922b00 0x2b0>,
- <0xfd922d80 0x7b>;
- clock-names = "iface";
- clocks = <&mmcc MDSS_AHB_CLK>;
- #clock-cells = <1>;
- vddio-supply = <&pma8084_l12>;
-
- qcom,dsi-phy-regulator-ldo-mode;
- };
--
2.7.4
Powered by blists - more mailing lists