linux-kernel - [PATCH v2 1/2] serial: 8250: Add UART_BUG

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20210519000704.3661773-2-andrew@aj.id.au>
Date:   Wed, 19 May 2021 09:37:03 +0930
From:   Andrew Jeffery <andrew@...id.au>
To:     linux-serial@...r.kernel.org
Cc:     gregkh@...uxfoundation.org, jirislaby@...nel.org, joel@....id.au,
        linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
        linux-aspeed@...ts.ozlabs.org, openbmc@...ts.ozlabs.org,
        jenmin_yuan@...eedtech.com, ryan_chen@...eedtech.com,
        miltonm@...ibm.com, ChiaWei Wang <chiawei_wang@...eedtech.com>
Subject: [PATCH v2 1/2] serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART

Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
LPC bus to the UART interface on the BMC's internal APB. As such there's
no RS-232 signalling involved - the UART interfaces on each bus are
directly connected as the producers and consumers of the one set of
FIFOs.

The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
at 33MHz. The difference in clock speeds exposes a race in the VUART
design where a Tx data burst on the APB interface can result in a byte
lost on the LPC interface. The symptom is LSR[DR] remains clear on the
LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
remains clear on the APB interface as the host has not consumed the data
the BMC has transmitted. In this state, the UART has stalled and no
further data can be transmitted without manual intervention (e.g.
resetting the FIFOs, resulting in loss of data).

The recommended work-around is to insert a read cycle on the APB
interface between writes to THR.

Cc: ChiaWei Wang <chiawei_wang@...eedtech.com>
Signed-off-by: Andrew Jeffery <andrew@...id.au>
---
 drivers/tty/serial/8250/8250.h              |  1 +
 drivers/tty/serial/8250/8250_aspeed_vuart.c |  1 +
 drivers/tty/serial/8250/8250_port.c         | 10 ++++++++++
 3 files changed, 12 insertions(+)

diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 52bb21205bb6..34aa2714f3c9 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -88,6 +88,7 @@ struct serial8250_config {
 #define UART_BUG_NOMSR	(1 << 2)	/* UART has buggy MSR status bits (Au1x00) */
 #define UART_BUG_THRE	(1 << 3)	/* UART has buggy THRE reassertion */
 #define UART_BUG_PARITY	(1 << 4)	/* UART mishandles parity if FIFO enabled */
+#define UART_BUG_TXRACE	(1 << 5)	/* UART Tx fails to set remote DR */
 
 
 #ifdef CONFIG_SERIAL_8250_SHARE_IRQ
diff --git a/drivers/tty/serial/8250/8250_aspeed_vuart.c b/drivers/tty/serial/8250/8250_aspeed_vuart.c
index a28a394ba32a..4caab8714e2c 100644
--- a/drivers/tty/serial/8250/8250_aspeed_vuart.c
+++ b/drivers/tty/serial/8250/8250_aspeed_vuart.c
@@ -440,6 +440,7 @@ static int aspeed_vuart_probe(struct platform_device *pdev)
 	port.port.status = UPSTAT_SYNC_FIFO;
 	port.port.dev = &pdev->dev;
 	port.port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
+	port.bugs |= UART_BUG_TXRACE;
 
 	rc = sysfs_create_group(&vuart->dev->kobj, &aspeed_vuart_attr_group);
 	if (rc < 0)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index d45dab1ab316..9d44b2b2ff18 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1809,6 +1809,16 @@ void serial8250_tx_chars(struct uart_8250_port *up)
 	count = up->tx_loadsz;
 	do {
 		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+		if (up->bugs & UART_BUG_TXRACE) {
+			/* The Aspeed BMC virtual UARTs have a bug where data
+			 * may get stuck in the BMC's Tx FIFO from bursts of
+			 * writes on the APB interface.
+			 *
+			 * Delay back-to-back writes by a read cycle to avoid
+			 * stalling the VUART.
+			 */
+			(void)serial_in(up, UART_SCR);
+		}
 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 		port->icount.tx++;
 		if (uart_circ_empty(xmit))
-- 
2.30.2