[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <2005328.bFqPmhE5MS@nvdebian>
Date: Thu, 27 May 2021 11:20:36 +1000
From: Alistair Popple <apopple@...dia.com>
To: Peter Xu <peterx@...hat.com>
CC: <linux-mm@...ck.org>, <akpm@...ux-foundation.org>,
<nouveau@...ts.freedesktop.org>, <bskeggs@...hat.com>,
<rcampbell@...dia.com>, <linux-doc@...r.kernel.org>,
<jhubbard@...dia.com>, <bsingharora@...il.com>,
<linux-kernel@...r.kernel.org>, <dri-devel@...ts.freedesktop.org>,
<hch@...radead.org>, <jglisse@...hat.com>, <willy@...radead.org>,
<jgg@...dia.com>, <hughd@...gle.com>
Subject: Re: [PATCH v9 06/10] mm/memory.c: Allow different return codes for copy_nonpresent_pte()
On Thursday, 27 May 2021 5:50:05 AM AEST Peter Xu wrote:
> On Mon, May 24, 2021 at 11:27:21PM +1000, Alistair Popple wrote:
> > Currently if copy_nonpresent_pte() returns a non-zero value it is
> > assumed to be a swap entry which requires further processing outside the
> > loop in copy_pte_range() after dropping locks. This prevents other
> > values being returned to signal conditions such as failure which a
> > subsequent change requires.
> >
> > Instead make copy_nonpresent_pte() return an error code if further
> > processing is required and read the value for the swap entry in the main
> > loop under the ptl.
> >
> > Signed-off-by: Alistair Popple <apopple@...dia.com>
> >
> > ---
> >
> > v9:
> >
> > New for v9 to allow device exclusive handling to occur in
> > copy_nonpresent_pte().
> > ---
> >
> > mm/memory.c | 12 +++++++-----
> > 1 file changed, 7 insertions(+), 5 deletions(-)
> >
> > diff --git a/mm/memory.c b/mm/memory.c
> > index 2fb455c365c2..e061cfa18c11 100644
> > --- a/mm/memory.c
> > +++ b/mm/memory.c
> > @@ -718,7 +718,7 @@ copy_nonpresent_pte(struct mm_struct *dst_mm, struct
> > mm_struct *src_mm,>
> > if (likely(!non_swap_entry(entry))) {
> >
> > if (swap_duplicate(entry) < 0)
> >
> > - return entry.val;
> > + return -EAGAIN;
> >
> > /* make sure dst_mm is on swapoff's mmlist. */
> > if (unlikely(list_empty(&dst_mm->mmlist))) {
> >
> > @@ -974,11 +974,13 @@ copy_pte_range(struct vm_area_struct *dst_vma,
> > struct vm_area_struct *src_vma,>
> > continue;
> >
> > }
> > if (unlikely(!pte_present(*src_pte))) {
> >
> > - entry.val = copy_nonpresent_pte(dst_mm, src_mm,
> > - dst_pte, src_pte,
> > - src_vma, addr, rss);
> > - if (entry.val)
> > + ret = copy_nonpresent_pte(dst_mm, src_mm,
> > + dst_pte, src_pte,
> > + src_vma, addr, rss);
> > + if (ret == -EAGAIN) {
> > + entry = pte_to_swp_entry(*src_pte);
> >
> > break;
> >
> > + }
> >
> > progress += 8;
> > continue;
> >
> > }
>
> Note that -EAGAIN was previously used by copy_present_page() for early cow
> use. Here later although we check entry.val first:
>
> if (entry.val) {
> if (add_swap_count_continuation(entry, GFP_KERNEL) < 0) {
> ret = -ENOMEM;
> goto out;
> }
> entry.val = 0;
> } else if (ret) {
> WARN_ON_ONCE(ret != -EAGAIN);
> prealloc = page_copy_prealloc(src_mm, src_vma, addr);
> if (!prealloc)
> return -ENOMEM;
> /* We've captured and resolved the error. Reset, try again.
> */ ret = 0;
> }
>
> We didn't reset "ret" in entry.val case (maybe we should?). Then in the next
> round of "goto again" if "ret" is unluckily untouched, it could reach the
> 2nd if check, and I think it could cause an unexpected
> page_copy_prealloc().
Thanks, I had considered that but saw "ret" was always set either by
copy_nonpresent_pte() or copy_present_pte(). However missed the "unlucky" case
at the start of the loop:
if (progress >= 32) {
progress = 0;
if (need_resched() ||
spin_needbreak(src_ptl) || pin_needbreak(dst_ptl))
break;
Looking at this again though checking different variables to figure out what
to do outside the locks and reusing error codes seems error prone. I reused -
EAGAIN for copy_nonpresent_pte() simply because that seemed the most sensible
error code, but I don't think that aids readability and it might be better to
use a unique error code for each case needing extra handling.
So it might be better if I update this patch to:
1) Use unique error codes for each case requiring special handling outside the
lock.
2) Only check "ret" to determine what to do outside locks (ie. not entry.val)
3) Document these.
4) Always reset ret after handling.
Thoughts?
- Alistair
> --
> Peter Xu
Powered by blists - more mailing lists