linux-kernel - [PATCH 2/2] MIPS: Malta: Do not byte-swap accesses to the CBUS UART

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <alpine.DEB.2.21.2105181705570.3032@angie.orcam.me.uk>
Date:   Thu, 10 Jun 2021 20:38:10 +0200 (CEST)
From:   "Maciej W. Rozycki" <macro@...am.me.uk>
To:     Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Jiri Slaby <jirislaby@...nel.org>,
        Thomas Bogendoerfer <tsbogend@...ha.franken.de>
cc:     linux-serial@...r.kernel.org, linux-mips@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: [PATCH 2/2] MIPS: Malta: Do not byte-swap accesses to the CBUS
 UART

Correct big-endian accesses to the CBUS UART, a Malta on-board discrete 
TI16C550C part wired directly to the system controller's device bus, and 
do not use byte swapping with the 32-bit accesses to the device.

The CBUS is used for devices such as the boot flash memory needed early 
on in system bootstrap even before PCI has been initialised.  Therefore 
it uses the system controller's device bus, which follows the endianness 
set with the CPU, which means no byte-swapping is ever required for data 
accesses to CBUS, unlike with PCI.

The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and 
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping 
with PCI systems.  Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.

As it happens the UPIO_MEM32BE access method makes use of the `ioread32' 
and `iowrite32' MMIO accessors, which still use `readl' and `writel' 
respectively, however they byte-swap data passed, effectively cancelling 
swapping done with the accessors themselves and making it suitable for 
the CBUS UART.

Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then, 
based on the endianness selected.  With this change in place the device 
is correctly recognised with big-endian Malta at boot, along with the 
Super I/O devices behind PCI:

Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A

Signed-off-by: Maciej W. Rozycki <macro@...am.me.uk>
Fixes: e7c4782f92fc ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence")
---
 arch/mips/mti-malta/malta-platform.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

linux-mips-malta-cbus-uart-be.diff
Index: linux-malta-cbus-uart/arch/mips/mti-malta/malta-platform.c
===================================================================
--- linux-malta-cbus-uart.orig/arch/mips/mti-malta/malta-platform.c
+++ linux-malta-cbus-uart/arch/mips/mti-malta/malta-platform.c
@@ -47,7 +47,8 @@ static struct plat_serial8250_port uart8
 		.mapbase	= 0x1f000900,	/* The CBUS UART */
 		.irq		= MIPS_CPU_IRQ_BASE + MIPSCPU_INT_MB2,
 		.uartclk	= 3686400,	/* Twice the usual clk! */
-		.iotype		= UPIO_MEM32,
+		.iotype		= IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) ?
+				  UPIO_MEM32BE : UPIO_MEM32,
 		.flags		= CBUS_UART_FLAGS,
 		.regshift	= 3,
 	},