| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <87wnr0zwxs.fsf@kernel.org>
Date: Fri, 11 Jun 2021 10:23:43 +0300
From: Felipe Balbi <balbi@...nel.org>
To: Wesley Cheng <wcheng@...eaurora.org>, gregkh@...uxfoundation.org
Cc: linux-usb@...r.kernel.org, linux-kernel@...r.kernel.org,
jackp@...eaurora.org
Subject: Re: [PATCH] usb: dwc3: gadget: Disable gadget IRQ during pullup
disable
Wesley Cheng <wcheng@...eaurora.org> writes:
> On 6/10/2021 11:21 AM, Wesley Cheng wrote:
>>
>>
>> On 6/10/2021 4:09 AM, Felipe Balbi wrote:
>>> Wesley Cheng <wcheng@...eaurora.org> writes:
>>>
>>>> Current sequence utilizes dwc3_gadget_disable_irq() alongside
>>>> synchronize_irq() to ensure that no further DWC3 events are generated.
>>>> However, the dwc3_gadget_disable_irq() API only disables device
>>>> specific events. Endpoint events can still be generated. Briefly
>>>> disable the interrupt line, so that the cleanup code can run to
>>>> prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
>>>> dwc3_stop_active_transfers() respectively)
>>>>
>>>> Without doing so, it can lead to both the interrupt handler and the
>>>> pullup disable routine both writing to the GEVNTCOUNT register, which
>>>> will cause an incorrect count being read from future interrupts.
>>>>
>>>> Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
>>>> Signed-off-by: Wesley Cheng <wcheng@...eaurora.org>
>>>> ---
>>>> drivers/usb/dwc3/gadget.c | 11 +++++------
>>>> 1 file changed, 5 insertions(+), 6 deletions(-)
>>>>
>>>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>>>> index 49ca5da..89aa9ac 100644
>>>> --- a/drivers/usb/dwc3/gadget.c
>>>> +++ b/drivers/usb/dwc3/gadget.c
>>>> @@ -2260,13 +2260,10 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
>>>> }
>>>>
>>>> /*
>>>> - * Synchronize any pending event handling before executing the controller
>>>> - * halt routine.
>>>> + * Synchronize and disable any further event handling while controller
>>>> + * is being enabled/disabled.
>>>> */
>>>> - if (!is_on) {
>>>> - dwc3_gadget_disable_irq(dwc);
>>>> - synchronize_irq(dwc->irq_gadget);
>>>> - }
>>>> + disable_irq(dwc->irq_gadget);
>>>>
>>>> spin_lock_irqsave(&dwc->lock, flags);
>>>
>>> spin_lock_irqsave() is already disabling interrupt, right? Why do we
>>> need another call to disable_irq()?
>>>
>>
>> Hi Felipe,
>>
>> Yes, I remember you brought up that point as well before. So when I
>> checked the logs (USB and scheduler ftrace) for this issue, I clearly
>> saw that we were handling a soft disconnect on CPU3 and then an DWC3 IRQ
>> being scheduled into CPU0. Last time we discussed, I mentioned that
>> spin_lock_irqsave() only disables interrupts on that particular CPU the
>> thread is running on.
>>
> Hi Felipe,
>
> Let me share the ftrace snippets as well:
>
> USB FTRACE:
>
> <idle>-0 [002] 304.567900: dwc3_gadget_ep_cmd name=ep0out cmd=1030 param0=0 param1=4026523648 param2=0 cmd_status=0
> <idle>-0 [004] 304.583225: dwc3_gadget_ep_cmd name=ep1out cmd=134152 param0=0 param1=0 param2=0 cmd_status=0
>
> //We don't have any logging in pullup disable, but this is when that
> occurs, as we start to see -ESHUTDOWN statuses due to stop active
> transfer.
argh, maybe we should add :-)
I noticed that the logs here look different. Did you modify dwc3 trace
events or is it a special tracer (just curious)? Anyway...
> <idle>-0 [004] 304.583237: dwc3_gadget_giveback name=ep1out req=1243650560 actual=0 length=16384 status=4294967188 zero=0 short_not_ok=0 no_interrupt=0
> <idle>-0 [004] 304.583275: dwc3_gadget_giveback name=ep1out req=1243645440 actual=0 length=16384 status=4294967188 zero=0 short_not_ok=0 no_interrupt=0
> <idle>-0 [004] 304.583282: dwc3_gadget_giveback name=ep1out req=1243648256 actual=0 length=16384 status=4294967188 zero=0 short_not_ok=0 no_interrupt=0
> <idle>-0 [004] 304.583312: dwc3_gadget_giveback name=ep1out req=4075146240 actual=0 length=16384 status=4294967188 zero=0 short_not_ok=0 no_interrupt=0
> ...
> //USB gadget disconnect is printed AFTER the pullup(0) routine is complete.
> <idle>-0 [004] 304.584240: usb_gadget_disconnect speed=3 max_speed=6 state=7 mA=500 sg_supported=1 is_otg=0 is_a_peripheral=0 b_hnp_enable=0 a_hnp_support=0 hnp_polling_support=0 host_request_flag=0 quirk_ep_out_aligned_size=0 quirk_altset_not_supp=0 quirk_stall_not_supp=0 quirk_zlp_not_supp=0 is_selfpowered=0 deactivated=0 connected=1 ret=4294967186
>
> ---------------------------------------------------------
> CPU2 SCHED FTRACE:
>
> kworker/u16:5-192 [002] 304.583354: irq_handler_entry irq=343 name=dwc3-msm
> kworker/u16:5-192 [002] 304.583356: irq_handler_exit irq=343 ret=0
> kworker/u16:5-192 [002] 304.583358: irq_handler_entry irq=343 name=dwc3
> kworker/u16:5-192 [002] 304.583366: irq_handler_exit irq=343 ret=2
> kworker/u16:5-192 [002] 304.583377: sched_wakeup comm=irq/343-dwc3 pid=20174 prio=100 success=1 target_cpu=2
> kworker/u16:5-192 [002] 304.583411: sched_switch: prev_comm=kworker/u16:5 prev_pid=192 prev_prio=120 prev_state=R ==> next_comm=irq/343-dwc3 next_pid=20174 next_prio=100
> irq/343-dwc3-20174 [002] 304.583454: irq_handler_entry irq=343 name=dwc3-msm
> irq/343-dwc3-20174 [002] 304.583455: irq_handler_exit irq=343 ret=0
> irq/343-dwc3-20174 [002] 304.583458: irq_handler_entry irq=343 name=dwc3
> irq/343-dwc3-20174 [002] 304.583465: irq_handler_exit irq=343 ret=2
>
> So if we assume that the point of error happens @ 304.567900 due to the
> below points:
> - DWC3 pullup disable routine synchronized IRQs (w/ previous logic)
> before calling stop active transfers.
> - DWC3 request statuses shows ESHUTDOWN, which occurs during stop active
> transfer, as we call giveback w/ that error code
>
> Then we can see that on CPU2, we're still getting DWC3 core IRQs, and
> DWC3 IRQ handler is returning --> 2, which is IRQ_WAKE_THREAD.
very good breakdown of the problem, thank you :-) What if we move the
spin_lock_irqsave() before that !is_on check and do away with
synchronize IRQ?
Then the only thing left would be ignore the interrupt events if they
still come, no?
Something like:
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 612825a39f82..aff9a4673830 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2260,20 +2260,12 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
return 0;
}
- /*
- * Synchronize any pending event handling before executing the controller
- * halt routine.
- */
- if (!is_on) {
- dwc3_gadget_disable_irq(dwc);
- synchronize_irq(dwc->irq_gadget);
- }
-
spin_lock_irqsave(&dwc->lock, flags);
if (!is_on) {
u32 count;
+ dwc3_gadget_disable_irq(dwc);
dwc->connected = false;
/*
* In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
@@ -3873,6 +3865,9 @@ static irqreturn_t dwc3_check_event_buf(struct dwc3_event_buffer *evt)
if (!count)
return IRQ_NONE;
+ if (!dwc->connected)
+ goto out_ignore;
+
evt->count = count;
evt->flags |= DWC3_EVENT_PENDING;
@@ -3887,6 +3882,7 @@ static irqreturn_t dwc3_check_event_buf(struct dwc3_event_buffer *evt)
if (amount < count)
memcpy(evt->cache, evt->buf, count - amount);
+out_ignore:
dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
return IRQ_WAKE_THREAD;
(totally untested, mind you :)
Ignoring the events in dwc3_check_event_buf() may be unnecessary since
we're already doing that in dwc3_pullup() after __dwc3_gadget_stop().
What do you think?
--
balbi
Download attachment "signature.asc" of type "application/pgp-signature" (512 bytes)
Powered by blists - more mailing lists