| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210615110636.23403-19-andre.przywara@arm.com>
Date: Tue, 15 Jun 2021 12:06:35 +0100
From: Andre Przywara <andre.przywara@....com>
To: Maxime Ripard <mripard@...nel.org>, Chen-Yu Tsai <wens@...e.org>,
Jernej Skrabec <jernej.skrabec@...il.com>
Cc: Rob Herring <robh@...nel.org>, Icenowy Zheng <icenowy@...c.io>,
Samuel Holland <samuel@...lland.org>,
linux-arm-kernel@...ts.infradead.org, linux-sunxi@...glegroups.com,
linux-sunxi@...ts.linux.dev, linux-kernel@...r.kernel.org,
Ondrej Jirman <megous@...ous.com>, devicetree@...r.kernel.org
Subject: [PATCH v7 18/19] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support
The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- unsupported Allwinner WiFi/BT chip
For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2
Signed-off-by: Andre Przywara <andre.przywara@....com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-orangepi-zero2.dts | 245 ++++++++++++++++++
2 files changed, 246 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 41ce680e5f8d..9ba4b5d92657 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -36,3 +36,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..a26201288872
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "OrangePi Zero2";
+ compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ status = "okay";
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdce>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdce>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp305: pmic@745 {
+ compatible = "x-powers,axp305", "x-powers,axp805",
+ "x-powers,axp806";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x745>;
+
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-sys";
+ };
+
+ reg_aldo2: aldo2 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext";
+ };
+
+ reg_aldo3: aldo3 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext2";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ bldo2 {
+ /* unused */
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ cldo1 {
+ /* reserved */
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-dram";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-eth-mmc";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.17.5
Powered by blists - more mailing lists