| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210622082031.GA590368@anxtwsw-Precision-3640-Tower>
Date: Tue, 22 Jun 2021 16:20:31 +0800
From: Xin Ji <xji@...logixsemi.com>
To: Neil Armstrong <narmstrong@...libre.com>
Cc: Robert Foss <robert.foss@...aro.org>,
Nicolas Boichat <drinkcat@...gle.com>,
Andrzej Hajda <a.hajda@...sung.com>,
Laurent Pinchart <Laurent.pinchart@...asonboard.com>,
Jonas Karlman <jonas@...boo.se>,
Dan Carpenter <dan.carpenter@...cle.com>,
David Airlie <airlied@...ux.ie>,
Daniel Vetter <daniel@...ll.ch>,
Boris Brezillon <boris.brezillon@...labora.com>,
Sam Ravnborg <sam@...nborg.org>,
Hsin-Yi Wang <hsinyi@...omium.org>, Torsten Duwe <duwe@....de>,
Vasily Khoruzhick <anarsoul@...il.com>,
Marek Szyprowski <m.szyprowski@...sung.com>,
Sheng Pan <span@...logixsemi.com>,
Bernie Liang <bliang@...logixsemi.com>,
Zhen Li <zhenli@...logixsemi.com>,
dri-devel@...ts.freedesktop.org, linux-kernel@...r.kernel.org,
devel@...verdev.osuosl.org
Subject: Re: [PATCH v8 3/4] drm/bridge: anx7625: add MIPI DPI input feature
On Wed, Jun 16, 2021 at 11:16:14AM +0200, Neil Armstrong wrote:
> On 16/06/2021 09:50, Xin Ji wrote:
> > The basic anx7625 driver only support MIPI DSI rx signal input.
> > This patch add MIPI DPI rx input configuration support, after apply
> > this patch, the driver can support DSI rx or DPI rx by adding
> > 'bus-type' in DT.
> >
> > Reviewed-by: Robert Foss <robert.foss@...aro.org>
> > Signed-off-by: Xin Ji <xji@...logixsemi.com>
> > ---
> > drivers/gpu/drm/bridge/analogix/anx7625.c | 245 ++++++++++++++++------
> > drivers/gpu/drm/bridge/analogix/anx7625.h | 18 +-
> > 2 files changed, 203 insertions(+), 60 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > index 048080e75016..fb2301a92704 100644
> > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > @@ -152,18 +152,18 @@ static int anx7625_write_and(struct anx7625_data *ctx,
> > return anx7625_reg_write(ctx, client, offset, (val & (mask)));
> > }
> >
> > -static int anx7625_write_and_or(struct anx7625_data *ctx,
> > - struct i2c_client *client,
> > - u8 offset, u8 and_mask, u8 or_mask)
> > +static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
> > {
> > - int val;
> > + int i, ret;
> >
> > - val = anx7625_reg_read(ctx, client, offset);
> > - if (val < 0)
> > - return val;
> > + ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
> > + AUDIO_CONTROL_REGISTER, 0x80);
> > + for (i = 0; i < 13; i++)
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > + VIDEO_BIT_MATRIX_12 + i,
> > + 0x18 + i);
> >
> > - return anx7625_reg_write(ctx, client,
> > - offset, (val & and_mask) | (or_mask));
> > + return ret;
> > }
> >
> > static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
> > @@ -221,38 +221,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx,
> > return ret;
> > }
> >
> > -static int anx7625_config_audio_input(struct anx7625_data *ctx)
> > -{
> > - struct device *dev = &ctx->client->dev;
> > - int ret;
> > -
> > - /* Channel num */
> > - ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > - AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
> > -
> > - /* FS */
> > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
> > - AUDIO_CHANNEL_STATUS_4,
> > - 0xf0, AUDIO_FS_48K);
> > - /* Word length */
> > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
> > - AUDIO_CHANNEL_STATUS_5,
> > - 0xf0, AUDIO_W_LEN_24_24MAX);
> > - /* I2S */
> > - ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
> > - AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
> > - ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
> > - AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
> > - /* Audio change flag */
> > - ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
> > - AP_AV_STATUS, AP_AUDIO_CHG);
> > -
> > - if (ret < 0)
> > - DRM_DEV_ERROR(dev, "fail to config audio.\n");
> > -
> > - return ret;
> > -}
> > -
> > /* Reduction of fraction a/b */
> > static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
> > {
> > @@ -412,7 +380,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
> > ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
> > MIPI_LANE_CTRL_0, 0xfc);
> > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
> > - MIPI_LANE_CTRL_0, 3);
> > + MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1);
> >
> > /* Htotal */
> > htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +
> > @@ -597,6 +565,76 @@ static int anx7625_dsi_config(struct anx7625_data *ctx)
> > return ret;
> > }
> >
> > +static int anx7625_api_dpi_config(struct anx7625_data *ctx)
> > +{
> > + struct device *dev = &ctx->client->dev;
> > + u16 freq = ctx->dt.pixelclock.min / 1000;
> > + int ret;
> > +
> > + /* configure pixel clock */
> > + ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> > + PIXEL_CLOCK_L, freq & 0xFF);
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> > + PIXEL_CLOCK_H, (freq >> 8));
> > +
> > + /* set DPI mode */
> > + /* set to DPI PLL module sel */
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
> > + MIPI_DIGITAL_PLL_9, 0x20);
> > + /* power down MIPI */
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
> > + MIPI_LANE_CTRL_10, 0x08);
> > + /* enable DPI mode */
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
> > + MIPI_DIGITAL_PLL_18, 0x1C);
> > + /* set first edge */
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > + VIDEO_CONTROL_0, 0x06);
> > + if (ret < 0)
> > + DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n");
> > +
> > + return ret;
> > +}
> > +
> > +static int anx7625_dpi_config(struct anx7625_data *ctx)
> > +{
> > + struct device *dev = &ctx->client->dev;
> > + int ret;
> > +
> > + DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
> > +
> > + /* DSC disable */
> > + ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
> > + R_DSC_CTRL_0, ~DSC_EN);
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n");
> > + return ret;
> > + }
> > +
> > + ret = anx7625_config_bit_matrix(ctx);
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "config bit matrix failed.\n");
> > + return ret;
> > + }
> > +
> > + ret = anx7625_api_dpi_config(ctx);
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n");
> > + return ret;
> > + }
> > +
> > + /* set MIPI RX EN */
> > + ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
> > + AP_AV_STATUS, AP_MIPI_RX_EN);
> > + /* clear mute flag */
> > + ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
> > + AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
> > + if (ret < 0)
> > + DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n");
> > +
> > + return ret;
> > +}
> > +
> > static void anx7625_dp_start(struct anx7625_data *ctx)
> > {
> > int ret;
> > @@ -607,9 +645,10 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
> > return;
> > }
> >
> > - anx7625_config_audio_input(ctx);
> > -
> > - ret = anx7625_dsi_config(ctx);
> > + if (ctx->pdata.is_dpi)
> > + ret = anx7625_dpi_config(ctx);
> > + else
> > + ret = anx7625_dsi_config(ctx);
> >
> > if (ret < 0)
> > DRM_DEV_ERROR(dev, "MIPI phy setup error.\n");
> > @@ -1047,6 +1086,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
> > return;
> > }
> >
> > + ctx->hpd_status = 1;
> > ctx->hpd_high_cnt++;
> >
> > /* Not support HDCP */
> > @@ -1056,8 +1096,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
> > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
> > /* Interrupt for DRM */
> > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
> > - if (ret < 0)
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n");
> > return;
> > + }
> >
> > ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
> > if (ret < 0)
> > @@ -1076,6 +1118,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
> > int ret, val;
> > struct device *dev = &ctx->client->dev;
> >
> > + /* Interrupt mode, no need poll HPD status, just return */
> > + if (ctx->pdata.intp_irq)
> > + return;
> > +
> > ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
> > ctx, val,
> > ((val & HPD_STATUS) || (val < 0)),
> > @@ -1103,6 +1149,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx)
> > ctx->slimport_edid_p.edid_block_num = -1;
> > }
> >
> > +static void anx7625_dp_adjust_swing(struct anx7625_data *ctx)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++)
> > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
> > + DP_TX_LANE0_SWING_REG0 + i,
> > + ctx->pdata.lane0_reg_data[i] & 0xFF);
> > +
> > + for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++)
> > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
> > + DP_TX_LANE1_SWING_REG0 + i,
> > + ctx->pdata.lane1_reg_data[i] & 0xFF);
> > +}
> > +
> > static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
> > {
> > struct device *dev = &ctx->client->dev;
> > @@ -1118,9 +1179,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
> > } else {
> > DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
> > anx7625_start_dp_work(ctx);
> > + anx7625_dp_adjust_swing(ctx);
> > }
> > -
> > - ctx->hpd_status = 1;
> > }
> >
> > static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
> > @@ -1197,20 +1257,72 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
> > return IRQ_HANDLED;
> > }
> >
> > +static int anx7625_get_swing_setting(struct device *dev,
> > + struct anx7625_platform_data *pdata)
> > +{
> > + int num_regs;
> > +
> > + if (of_get_property(dev->of_node,
> > + "analogix,lane0-swing", &num_regs)) {
> > + if (num_regs > DP_TX_SWING_REG_CNT)
> > + num_regs = DP_TX_SWING_REG_CNT;
> > +
> > + pdata->dp_lane0_swing_reg_cnt = num_regs;
> > + of_property_read_u32_array(dev->of_node, "analogix,lane0-swing",
> > + pdata->lane0_reg_data, num_regs);
> > + }
> > +
> > + if (of_get_property(dev->of_node,
> > + "analogix,lane1-swing", &num_regs)) {
> > + if (num_regs > DP_TX_SWING_REG_CNT)
> > + num_regs = DP_TX_SWING_REG_CNT;
> > +
> > + pdata->dp_lane1_swing_reg_cnt = num_regs;
> > + of_property_read_u32_array(dev->of_node, "analogix,lane1-swing",
> > + pdata->lane1_reg_data, num_regs);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > static int anx7625_parse_dt(struct device *dev,
> > struct anx7625_platform_data *pdata)
> > {
> > - struct device_node *np = dev->of_node;
> > + struct device_node *np = dev->of_node, *ep0;
> > struct drm_panel *panel;
> > int ret;
> > + int bus_type, mipi_lanes;
> >
> > + anx7625_get_swing_setting(dev, pdata);
> > +
> > + pdata->is_dpi = 1; /* default dpi mode */
> > pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0);
> > if (!pdata->mipi_host_node) {
> > DRM_DEV_ERROR(dev, "fail to get internal panel.\n");
> > return -ENODEV;
> > }
> >
> > - DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
> > + bus_type = 5;
> > + mipi_lanes = MAX_LANES_SUPPORT;
> > + ep0 = of_graph_get_endpoint_by_regs(np, 0, 0);
> > + if (ep0) {
> > + if (of_property_read_u32(ep0, "bus-type", &bus_type))
> > + bus_type = 0;
> > +
> > + mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes");
> > + }
> > +
> > + if (bus_type == 5) /* bus type is Parallel(DSI) */
> > + pdata->is_dpi = 0;
>
> Maybe you can use the include/media/v4l2-fwnode.h V4L2_FWNODE_BUS_TYPE_ defines here instead.
>
> Neil
Hi Neil, OK, I'll use the properly macro instead of fixing value.
Thanks,
Xin
>
> > +
> > + pdata->mipi_lanes = mipi_lanes;
> > + if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0)
> > + pdata->mipi_lanes = MAX_LANES_SUPPORT;
> > +
> > + if (pdata->is_dpi)
> > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n");
> > + else
> > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n");
> >
> > ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
> > if (ret < 0) {
> > @@ -1273,9 +1385,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx)
> > {
> > struct device *dev = &ctx->client->dev;
> >
> > - DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n");
> > + DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n");
> > +
> > + if (ctx->pdata.panel_bridge)
> > + return connector_status_connected;
> >
> > - return connector_status_connected;
> > + return ctx->hpd_status ? connector_status_connected :
> > + connector_status_disconnected;
> > }
> >
> > static int anx7625_attach_dsi(struct anx7625_data *ctx)
> > @@ -1303,7 +1419,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx)
> > return -EINVAL;
> > }
> >
> > - dsi->lanes = 4;
> > + dsi->lanes = ctx->pdata.mipi_lanes;
> > dsi->format = MIPI_DSI_FMT_RGB888;
> > dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> > MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
> > @@ -1349,10 +1465,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge,
> > return -ENODEV;
> > }
> >
> > - err = anx7625_attach_dsi(ctx);
> > - if (err) {
> > - DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
> > - return err;
> > + if (!ctx->pdata.is_dpi) {
> > + err = anx7625_attach_dsi(ctx);
> > + if (err) {
> > + DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
> > + return err;
> > + }
> > }
> >
> > if (ctx->pdata.panel_bridge) {
> > @@ -1451,6 +1569,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge,
> >
> > DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n");
> >
> > + /* No need fixup for external monitor */
> > + if (!ctx->pdata.panel_bridge)
> > + return true;
> > +
> > hsync = mode->hsync_end - mode->hsync_start;
> > hfp = mode->hsync_start - mode->hdisplay;
> > hbp = mode->htotal - mode->hsync_end;
> > @@ -1827,8 +1949,13 @@ static int anx7625_i2c_probe(struct i2c_client *client,
> >
> > platform->bridge.funcs = &anx7625_bridge_funcs;
> > platform->bridge.of_node = client->dev.of_node;
> > - platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
> > - platform->bridge.type = DRM_MODE_CONNECTOR_eDP;
> > + platform->bridge.ops = DRM_BRIDGE_OP_EDID;
> > + if (!platform->pdata.panel_bridge)
> > + platform->bridge.ops |= DRM_BRIDGE_OP_HPD |
> > + DRM_BRIDGE_OP_DETECT;
> > + platform->bridge.type = platform->pdata.panel_bridge ?
> > + DRM_MODE_CONNECTOR_eDP :
> > + DRM_MODE_CONNECTOR_DisplayPort;
> > drm_bridge_add(&platform->bridge);
> >
> > DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
> > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > index 034c3840028f..65db38e5da9a 100644
> > --- a/drivers/gpu/drm/bridge/analogix/anx7625.h
> > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > @@ -141,12 +141,20 @@
> > #define HORIZONTAL_BACK_PORCH_H 0x22 /* Bit[7:4] are reserved */
> >
> > /******** END of I2C Address 0x72 *********/
> > +
> > +/***************************************************************/
> > +/* Register definition of device address 0x7a */
> > +#define DP_TX_SWING_REG_CNT 0x14
> > +#define DP_TX_LANE0_SWING_REG0 0x00
> > +#define DP_TX_LANE1_SWING_REG0 0x14
> > +/******** END of I2C Address 0x7a *********/
> > +
> > /***************************************************************/
> > /* Register definition of device address 0x7e */
> >
> > #define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E
> >
> > -#define FLASH_LOAD_STA 0x05
> > +#define FLASH_LOAD_STA 0x05
> > #define FLASH_LOAD_STA_CHK BIT(7)
> >
> > #define XTAL_FRQ_SEL 0x3F
> > @@ -347,12 +355,20 @@ struct s_edid_data {
> >
> > /***************** Display End *****************/
> >
> > +#define MAX_LANES_SUPPORT 4
> > +
> > struct anx7625_platform_data {
> > struct gpio_desc *gpio_p_on;
> > struct gpio_desc *gpio_reset;
> > struct regulator_bulk_data supplies[3];
> > struct drm_bridge *panel_bridge;
> > int intp_irq;
> > + int is_dpi;
> > + int mipi_lanes;
> > + int dp_lane0_swing_reg_cnt;
> > + int lane0_reg_data[DP_TX_SWING_REG_CNT];
> > + int dp_lane1_swing_reg_cnt;
> > + int lane1_reg_data[DP_TX_SWING_REG_CNT];
> > u32 low_power_mode;
> > struct device_node *mipi_host_node;
> > };
> >
Powered by blists - more mailing lists