| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1624726268-14869-2-git-send-email-rajeevny@codeaurora.org>
Date: Sat, 26 Jun 2021 22:21:03 +0530
From: Rajeev Nandan <rajeevny@...eaurora.org>
To: dri-devel@...ts.freedesktop.org, linux-arm-msm@...r.kernel.org,
freedreno@...ts.freedesktop.org, devicetree@...r.kernel.org
Cc: Rajeev Nandan <rajeevny@...eaurora.org>,
linux-kernel@...r.kernel.org, thierry.reding@...il.com,
sam@...nborg.org, robdclark@...il.com, dianders@...omium.org,
lyude@...hat.com, jani.nikula@...el.com, robh@...nel.org,
laurent.pinchart@...asonboard.com, a.hajda@...sung.com,
daniel.thompson@...aro.org, hoegsberg@...omium.org,
abhinavk@...eaurora.org, seanpaul@...omium.org,
kalyan_t@...eaurora.org, mkrishn@...eaurora.org,
lee.jones@...aro.org, jingoohan1@...il.com,
linux-fbdev@...r.kernel.org
Subject: [v8 1/6] drm/panel: add basic DP AUX backlight support
Some panels support backlight control over DP AUX channel using
VESA's standard backlight control interface.
Using new DRM eDP backlight helpers, add support to create and
register a backlight for those panels in drm_panel to simplify
the panel drivers.
The panel driver with access to "struct drm_dp_aux" can create and
register a backlight device using following code snippet in its
probe() function:
err = drm_panel_dp_aux_backlight(panel, aux);
if (err)
return err;
Then drm_panel will handle backlight_(enable|disable) calls
similar to the case when drm_panel_of_backlight() is used.
Currently, we are not supporting one feature where the source
device can combine the backlight brightness levels set through
DP AUX and the BL_PWM_DIM eDP connector pin. Since it's not
required for the basic backlight controls, it can be added later.
Signed-off-by: Rajeev Nandan <rajeevny@...eaurora.org>
Reviewed-by: Douglas Anderson <dianders@...omium.org>
Reviewed-by: Lyude Paul <lyude@...hat.com>
---
Changes in v5:
- New
Changes in v6:
- Fixed ordering of memory allocation (Douglas)
- Updated word wrapping in a comment (Douglas)
Changes in v8:
- Now using backlight_is_blank() to get the backlight blank status (Sam Ravnborg)
drivers/gpu/drm/drm_panel.c | 108 ++++++++++++++++++++++++++++++++++++++++++++
include/drm/drm_panel.h | 15 ++++--
2 files changed, 119 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/drm_panel.c b/drivers/gpu/drm/drm_panel.c
index f634371..4fa1e3b 100644
--- a/drivers/gpu/drm/drm_panel.c
+++ b/drivers/gpu/drm/drm_panel.c
@@ -26,12 +26,20 @@
#include <linux/module.h>
#include <drm/drm_crtc.h>
+#include <drm/drm_dp_helper.h>
#include <drm/drm_panel.h>
#include <drm/drm_print.h>
static DEFINE_MUTEX(panel_lock);
static LIST_HEAD(panel_list);
+struct dp_aux_backlight {
+ struct backlight_device *base;
+ struct drm_dp_aux *aux;
+ struct drm_edp_backlight_info info;
+ bool enabled;
+};
+
/**
* DOC: drm panel
*
@@ -342,6 +350,106 @@ int drm_panel_of_backlight(struct drm_panel *panel)
return 0;
}
EXPORT_SYMBOL(drm_panel_of_backlight);
+
+static int dp_aux_backlight_update_status(struct backlight_device *bd)
+{
+ struct dp_aux_backlight *bl = bl_get_data(bd);
+ u16 brightness = backlight_get_brightness(bd);
+ int ret = 0;
+
+ if (!backlight_is_blank(bd)) {
+ if (!bl->enabled) {
+ drm_edp_backlight_enable(bl->aux, &bl->info, brightness);
+ bl->enabled = true;
+ return 0;
+ }
+ ret = drm_edp_backlight_set_level(bl->aux, &bl->info, brightness);
+ } else {
+ if (bl->enabled) {
+ drm_edp_backlight_disable(bl->aux, &bl->info);
+ bl->enabled = false;
+ }
+ }
+
+ return ret;
+}
+
+static const struct backlight_ops dp_aux_bl_ops = {
+ .update_status = dp_aux_backlight_update_status,
+};
+
+/**
+ * drm_panel_dp_aux_backlight - create and use DP AUX backlight
+ * @panel: DRM panel
+ * @aux: The DP AUX channel to use
+ *
+ * Use this function to create and handle backlight if your panel
+ * supports backlight control over DP AUX channel using DPCD
+ * registers as per VESA's standard backlight control interface.
+ *
+ * When the panel is enabled backlight will be enabled after a
+ * successful call to &drm_panel_funcs.enable()
+ *
+ * When the panel is disabled backlight will be disabled before the
+ * call to &drm_panel_funcs.disable().
+ *
+ * A typical implementation for a panel driver supporting backlight
+ * control over DP AUX will call this function at probe time.
+ * Backlight will then be handled transparently without requiring
+ * any intervention from the driver.
+ *
+ * drm_panel_dp_aux_backlight() must be called after the call to drm_panel_init().
+ *
+ * Return: 0 on success or a negative error code on failure.
+ */
+int drm_panel_dp_aux_backlight(struct drm_panel *panel, struct drm_dp_aux *aux)
+{
+ struct dp_aux_backlight *bl;
+ struct backlight_properties props = { 0 };
+ u16 current_level;
+ u8 current_mode;
+ u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE];
+ int ret;
+
+ if (!panel || !panel->dev || !aux)
+ return -EINVAL;
+
+ ret = drm_dp_dpcd_read(aux, DP_EDP_DPCD_REV, edp_dpcd,
+ EDP_DISPLAY_CTL_CAP_SIZE);
+ if (ret < 0)
+ return ret;
+
+ if (!drm_edp_backlight_supported(edp_dpcd)) {
+ DRM_DEV_INFO(panel->dev, "DP AUX backlight is not supported\n");
+ return 0;
+ }
+
+ bl = devm_kzalloc(panel->dev, sizeof(*bl), GFP_KERNEL);
+ if (!bl)
+ return -ENOMEM;
+
+ bl->aux = aux;
+
+ ret = drm_edp_backlight_init(aux, &bl->info, 0, edp_dpcd,
+ ¤t_level, ¤t_mode);
+ if (ret < 0)
+ return ret;
+
+ props.type = BACKLIGHT_RAW;
+ props.brightness = current_level;
+ props.max_brightness = bl->info.max;
+
+ bl->base = devm_backlight_device_register(panel->dev, "dp_aux_backlight",
+ panel->dev, bl,
+ &dp_aux_bl_ops, &props);
+ if (IS_ERR(bl->base))
+ return PTR_ERR(bl->base);
+
+ panel->backlight = bl->base;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_panel_dp_aux_backlight);
#endif
MODULE_AUTHOR("Thierry Reding <treding@...dia.com>");
diff --git a/include/drm/drm_panel.h b/include/drm/drm_panel.h
index 33605c3..3ebfaa6 100644
--- a/include/drm/drm_panel.h
+++ b/include/drm/drm_panel.h
@@ -32,6 +32,7 @@ struct backlight_device;
struct device_node;
struct drm_connector;
struct drm_device;
+struct drm_dp_aux;
struct drm_panel;
struct display_timing;
@@ -64,8 +65,8 @@ enum drm_panel_orientation;
* the panel. This is the job of the .unprepare() function.
*
* Backlight can be handled automatically if configured using
- * drm_panel_of_backlight(). Then the driver does not need to implement the
- * functionality to enable/disable backlight.
+ * drm_panel_of_backlight() or drm_panel_dp_aux_backlight(). Then the driver
+ * does not need to implement the functionality to enable/disable backlight.
*/
struct drm_panel_funcs {
/**
@@ -144,8 +145,8 @@ struct drm_panel {
* Backlight device, used to turn on backlight after the call
* to enable(), and to turn off backlight before the call to
* disable().
- * backlight is set by drm_panel_of_backlight() and drivers
- * shall not assign it.
+ * backlight is set by drm_panel_of_backlight() or
+ * drm_panel_dp_aux_backlight() and drivers shall not assign it.
*/
struct backlight_device *backlight;
@@ -208,11 +209,17 @@ static inline int of_drm_get_panel_orientation(const struct device_node *np,
#if IS_ENABLED(CONFIG_DRM_PANEL) && (IS_BUILTIN(CONFIG_BACKLIGHT_CLASS_DEVICE) || \
(IS_MODULE(CONFIG_DRM) && IS_MODULE(CONFIG_BACKLIGHT_CLASS_DEVICE)))
int drm_panel_of_backlight(struct drm_panel *panel);
+int drm_panel_dp_aux_backlight(struct drm_panel *panel, struct drm_dp_aux *aux);
#else
static inline int drm_panel_of_backlight(struct drm_panel *panel)
{
return 0;
}
+static inline int drm_panel_dp_aux_backlight(struct drm_panel *panel,
+ struct drm_dp_aux *aux)
+{
+ return 0;
+}
#endif
#endif
--
2.7.4
Powered by blists - more mailing lists