| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <33f9ab8ea253c01d3311346bc871d7f62213215f.camel@puri.sm>
Date: Thu, 15 Jul 2021 08:49:51 +0200
From: Martin Kepplinger <martin.kepplinger@...i.sm>
To: Laurent Pinchart <laurent.pinchart@...asonboard.com>
Cc: festevam@...il.com, krzk@...nel.org, devicetree@...r.kernel.org,
kernel@...gutronix.de, kernel@...i.sm,
linux-arm-kernel@...ts.infradead.org, linux-imx@....com,
linux-kernel@...r.kernel.org, linux-media@...r.kernel.org,
linux-staging@...ts.linux.dev, m.felsch@...gutronix.de,
mchehab@...nel.org, phone-devel@...r.kernel.org, robh@...nel.org,
shawnguo@...nel.org, slongerbeam@...il.com
Subject: Re: [PATCH v6 2/3] media: imx: add a driver for i.MX8MQ mipi csi rx
phy and controller
Am Mittwoch, dem 14.07.2021 um 21:24 +0300 schrieb Laurent Pinchart:
> Hi Martin,
>
> Thank you for the patch.
thank you for reviewing.
>
> On Wed, Jul 14, 2021 at 01:19:30PM +0200, Martin Kepplinger wrote:
> > Add a driver to support the i.MX8MQ MIPI CSI receiver. The hardware
> > side
> > is based on
> >
> > https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.70_2.3.0
> >
> > It's built as part of VIDEO_IMX7_CSI because that's documented to
> > support
> > i.MX8M platforms. This driver adds i.MX8MQ support where currently
> > only the
> > i.MX8MM platform has been supported.
> >
> > Signed-off-by: Martin Kepplinger <martin.kepplinger@...i.sm>
> > ---
> > drivers/staging/media/imx/Makefile | 1 +
> > drivers/staging/media/imx/imx8mq-mipi-csi2.c | 949
> > +++++++++++++++++++
> > 2 files changed, 950 insertions(+)
> > create mode 100644 drivers/staging/media/imx/imx8mq-mipi-csi2.c
> >
> > diff --git a/drivers/staging/media/imx/Makefile
> > b/drivers/staging/media/imx/Makefile
> > index 6ac33275cc97..19c2fc54d424 100644
> > --- a/drivers/staging/media/imx/Makefile
> > +++ b/drivers/staging/media/imx/Makefile
> > @@ -16,3 +16,4 @@ obj-$(CONFIG_VIDEO_IMX_CSI) += imx6-mipi-csi2.o
> >
> > obj-$(CONFIG_VIDEO_IMX7_CSI) += imx7-media-csi.o
> > obj-$(CONFIG_VIDEO_IMX7_CSI) += imx7-mipi-csis.o
> > +obj-$(CONFIG_VIDEO_IMX7_CSI) += imx8mq-mipi-csi2.o
> > diff --git a/drivers/staging/media/imx/imx8mq-mipi-csi2.c
> > b/drivers/staging/media/imx/imx8mq-mipi-csi2.c
> > new file mode 100644
> > index 000000000000..949b3ef7a20a
> > --- /dev/null
> > +++ b/drivers/staging/media/imx/imx8mq-mipi-csi2.c
> > @@ -0,0 +1,949 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Freescale i.MX8MQ SoC series MIPI-CSI2 receiver driver
>
> Maybe they should be called NXP these days :-)
>
> > + *
> > + * Copyright (C) 2021 Purism SPC
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/errno.h>
> > +#include <linux/interconnect.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/mutex.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/reset.h>
> > +#include <linux/spinlock.h>
> > +
> > +#include <media/v4l2-common.h>
> > +#include <media/v4l2-device.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-mc.h>
> > +#include <media/v4l2-subdev.h>
> > +
> > +#define MIPI_CSI2_DRIVER_NAME "imx8mq-mipi-csi2"
> > +#define
> > MIPI_CSI2_SUBDEV_NAME MIPI_CSI2_DRIVER_NAME
> > +
> > +#define MIPI_CSI2_PAD_SINK 0
> > +#define MIPI_CSI2_PAD_SOURCE 1
> > +#define MIPI_CSI2_PADS_NUM 2
> > +
> > +#define MIPI_CSI2_DEF_PIX_WIDTH 640
> > +#define MIPI_CSI2_DEF_PIX_HEIGHT 480
> > +
> > +/* Register map definition */
> > +
> > +/* i.MX8MQ CSI-2 controller CSR */
> > +#define CSI2RX_CFG_NUM_LANES 0x100
> > +#define CSI2RX_CFG_DISABLE_DATA_LANES 0x104
> > +#define CSI2RX_BIT_ERR 0x108
> > +#define CSI2RX_IRQ_STATUS 0x10c
> > +#define CSI2RX_IRQ_MASK 0x110
> > +#define CSI2RX_IRQ_MASK_ALL 0x1ff
> > +#define CSI2RX_IRQ_MASK_ULPS_STATUS_CHANGE 0x8
> > +#define CSI2RX_ULPS_STATUS 0x114
> > +#define CSI2RX_PPI_ERRSOT_HS 0x118
> > +#define CSI2RX_PPI_ERRSOTSYNC_HS 0x11c
> > +#define CSI2RX_PPI_ERRESC 0x120
> > +#define CSI2RX_PPI_ERRSYNCESC 0x124
> > +#define CSI2RX_PPI_ERRCONTROL 0x128
> > +#define CSI2RX_CFG_DISABLE_PAYLOAD_0 0x12c
> > +#define CSI2RX_CFG_VID_P_FIFO_SEND_LEVEL 0x188
> > +#define CSI2RX_CFG_DISABLE_PAYLOAD_1 0x130
> > +
> > +enum {
> > + ST_POWERED = 1,
> > + ST_STREAMING = 2,
> > + ST_SUSPENDED = 4,
> > +};
> > +
> > +static const char * const imx8mq_mipi_csi_clk_id[] = {
> > + "core",
> > + "esc",
> > + "ui",
> > +};
> > +
> > +#define CSI2_NUM_CLKS ARRAY_SIZE(imx8mq_mipi_csi_clk_id)
> > +
> > +#define GPR_CSI2_1_RX_ENABLE BIT(13)
> > +#define GPR_CSI2_1_VID_INTFC_ENB BIT(12)
> > +#define GPR_CSI2_1_HSEL BIT(10)
> > +#define GPR_CSI2_1_CONT_CLK_MODE BIT(8)
> > +#define GPR_CSI2_1_S_PRG_RXHS_SETTLE(x) (((x) & 0x3f) << 2)
> > +
> > +/*
> > + * The send level configures the number of entries that must
> > accumulate in
> > + * the Pixel FIFO before the data will be transferred to the video
> > output.
> > + * See
> > https://community.nxp.com/t5/i-MX-Processors/IMX8M-MIPI-CSI-Host-Controller-send-level/m-p/864005/highlight/true#M131704
> > + */
> > +#define CSI2RX_SEND_LEVEL 64
> > +
> > +struct csi_state {
> > + struct device *dev;
> > + void __iomem *regs;
> > + struct clk_bulk_data clks[CSI2_NUM_CLKS];
> > + struct reset_control *rst;
> > + struct regulator *mipi_phy_regulator;
> > +
> > + struct v4l2_subdev sd;
> > + struct media_pad pads[MIPI_CSI2_PADS_NUM];
> > + struct v4l2_async_notifier notifier;
> > + struct v4l2_subdev *src_sd;
> > +
> > + struct v4l2_fwnode_bus_mipi_csi2 bus;
> > +
> > + struct mutex lock; /* Protect csi2_fmt, format_mbus, state,
> > hs_settle*/
>
> Missing space before */
>
> > + const struct csi2_pix_format *csi2_fmt;
> > + struct v4l2_mbus_framefmt format_mbus[MIPI_CSI2_PADS_NUM];
> > + u32 state;
> > + u32 hs_settle;
> > +
> > + struct regmap *phy_gpr;
> > + u8 phy_gpr_reg;
> > +
> > + struct icc_path *icc_path;
> > + s32 icc_path_bw;
> > +};
> > +
> > +/* ---------------------------------------------------------------
> > --------------
> > + * Format helpers
> > + */
> > +
> > +struct csi2_pix_format {
> > + u32 code;
> > + u8 width;
> > +};
> > +
> > +static const struct csi2_pix_format imx8mq_mipi_csi_formats[] = {
> > + /* RAW (Bayer and greyscale) formats. */
> > + {
> > + .code = MEDIA_BUS_FMT_SBGGR8_1X8,
> > + .width = 8,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGBRG8_1X8,
> > + .width = 8,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGRBG8_1X8,
> > + .width = 8,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SRGGB8_1X8,
> > + .width = 8,
> > + }, {
> > + .code = MEDIA_BUS_FMT_Y8_1X8,
> > + .width = 8,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SBGGR10_1X10,
> > + .width = 10,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGBRG10_1X10,
> > + .width = 10,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGRBG10_1X10,
> > + .width = 10,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SRGGB10_1X10,
> > + .width = 10,
> > + }, {
> > + .code = MEDIA_BUS_FMT_Y10_1X10,
> > + .width = 10,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SBGGR12_1X12,
> > + .width = 12,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGBRG12_1X12,
> > + .width = 12,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGRBG12_1X12,
> > + .width = 12,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SRGGB12_1X12,
> > + .width = 12,
> > + }, {
> > + .code = MEDIA_BUS_FMT_Y12_1X12,
> > + .width = 12,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SBGGR14_1X14,
> > + .width = 14,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGBRG14_1X14,
> > + .width = 14,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SGRBG14_1X14,
> > + .width = 14,
> > + }, {
> > + .code = MEDIA_BUS_FMT_SRGGB14_1X14,
> > + .width = 14,
> > + }, {
> > + /* YUV formats */
> > + .code = MEDIA_BUS_FMT_YUYV8_2X8,
> > + .width = 16,
> > + }, {
> > + .code = MEDIA_BUS_FMT_YUYV8_1X16,
> > + .width = 16,
> > + }
> > +};
> > +
> > +static const struct csi2_pix_format *find_csi2_format(u32 code)
> > +{
> > + unsigned int i;
> > +
> > + for (i = 0; i < ARRAY_SIZE(imx8mq_mipi_csi_formats); i++)
> > + if (code == imx8mq_mipi_csi_formats[i].code)
> > + return &imx8mq_mipi_csi_formats[i];
> > + return NULL;
> > +}
> > +
> > +/* ---------------------------------------------------------------
> > --------------
> > + * Hardware configuration
> > + */
> > +
> > +static inline void imx8mq_mipi_csi_write(struct csi_state *state,
> > u32 reg, u32 val)
> > +{
> > + writel(val, state->regs + reg);
> > +}
> > +
> > +static int imx8mq_mipi_csi_sw_reset(struct csi_state *state)
> > +{
> > + int ret;
> > +
> > + ret = reset_control_assert(state->rst);
>
> That's peculiar, is there no need to deassert reset ?
I tried different things here that would look more intuitive, but in
the end only this worked, which is directly taken from
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.70_2.3.0#n105
(actual register value read from DT) that results in exactly the same
register bits set like this assertation.
Powered by blists - more mailing lists