| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAAYoRsWQ25O=7msQfvH5qRRK80JrpfLOQdG2BQrGx9_wpOX_wQ@mail.gmail.com>
Date: Thu, 29 Jul 2021 08:23:48 -0700
From: Doug Smythies <dsmythies@...us.net>
To: "Rafael J. Wysocki" <rjw@...ysocki.net>
Cc: "Rafael J. Wysocki" <rafael@...nel.org>,
LKML <linux-kernel@...r.kernel.org>,
Linux PM <linux-pm@...r.kernel.org>,
dsmythies <dsmythies@...us.net>
Subject: Re: [PATCH v1 0/5] cpuidle: teo: Rework the idle state selection logic
On Wed, Jul 28, 2021 at 11:34 PM Doug Smythies <dsmythies@...us.net> wrote:
>
> On Wed, Jul 28, 2021 at 10:47 AM Rafael J. Wysocki <rjw@...ysocki.net> wrote:
> >
> > On Wednesday, July 28, 2021 3:52:51 PM CEST Rafael J. Wysocki wrote:
> > > On Tue, Jul 27, 2021 at 10:06 PM Doug Smythies <dsmythies@...us.net> wrote:
> > > >
> > > > Hi Rafael,
> > > >
> > > > Further to my reply of 2021.07.04 on this, I have
> > > > continued to work with and test this patch set.
> > > >
> > > > On 2021.06.02 11:14 Rafael J. Wysocki wrote:
> > > >
> > > > >This series of patches addresses some theoretical shortcoming in the
> > > > > TEO (Timer Events Oriented) cpuidle governor by reworking its idle
> > > > > state selection logic to some extent.
> > > > >
> > > > > Patches [1-2/5] are introductory cleanups and the substantial changes are
> > > > > made in patches [3-4/5] (please refer to the changelogs of these two
> > > > > patches for details). The last patch only deals with documentation.
> > > > >
> > > > > Even though this work is mostly based on theoretical considerations, it
> > > > > shows a measurable reduction of the number of cases in which the shallowest
> > > > > idle state is selected while it would be more beneficial to select a deeper
> > > > > one or the deepest idle state is selected while it would be more beneficial to
> > > > > select a shallower one, which should be a noticeable improvement.
> > > >
> > > > I am concentrating in the idle state 0 and 1 area.
> > > > When I disable idle state 0, the expectation is its
> > > > usage will fall to idle state 1. It doesn't.
> > > >
> > > > Conditions:
> > > > CPU: Intel(R) Core(TM) i5-10600K CPU @ 4.10GHz
> > > > HWP: disabled
> > > > CPU frequency scaling driver: intel_pstate, active
> > > > CPU frequency scaling governor: performance.
> > > > Idle configuration: As a COMETLAKE processor, with 4 idle states.
> > > > Sample time for below: 1 minute.
> > > > Workflow: Cross core named pipe token passing, 12 threads.
> > > >
> > > > Kernel 5.14-rc3: idle: teo governor
> > > >
> > > > All idle states enabled: PASS
> > > > Processor: 97 watts
> > > > Idle state 0 entries: 811151
> > > > Idle state 1 entries: 140300776
> > > > Idle state 2 entries: 889
> > > > Idle state 3 entries: 8
> > > >
> > > > Idle state 0 disabled: FAIL <<<<<
> > > > Processor: 96 watts
> > > > Idle state 0 entries: 0
> > > > Idle state 1 entries: 65599283
> > > > Idle state 2 entries: 364399
> > > > Idle state 3 entries: 65112651
> > >
> > > This looks odd.
> > >
> > > Thanks for the report, I'll take a look at this.
> >
> > I have found an issue in the code that may be responsible for the
> > observed behavior and should be addressed by the appended patch (not
> > tested yet).
> >
> > Basically, the "disabled" check in the second loop over states in
> > teo_select() needs to exclude the first enabled state, because
> > there are no more states to check after that.
> >
> > Plus the time span check needs to be done when the given state
> > is about to be selected, because otherwise the function may end up
> > returning a state for which the sums are too low.
> >
> > Thanks!
> >
> > ---
> > drivers/cpuidle/governors/teo.c | 26 ++++++++++++++------------
> > 1 file changed, 14 insertions(+), 12 deletions(-)
> >
> > Index: linux-pm/drivers/cpuidle/governors/teo.c
> > ===================================================================
> > --- linux-pm.orig/drivers/cpuidle/governors/teo.c
> > +++ linux-pm/drivers/cpuidle/governors/teo.c
> > @@ -404,25 +404,27 @@ static int teo_select(struct cpuidle_dri
> > intercept_sum += bin->intercepts;
> > recent_sum += bin->recent;
> >
> > - if (dev->states_usage[i].disable)
> > + if (dev->states_usage[i].disable && i > idx0)
> > continue;
> >
> > span_ns = teo_middle_of_bin(i, drv);
> > - if (!teo_time_ok(span_ns)) {
> > - /*
> > - * The current state is too shallow, so select
> > - * the first enabled deeper state.
> > - */
> > - duration_ns = last_enabled_span_ns;
> > - idx = last_enabled_idx;
> > - break;
> > - }
> >
> > if ((!alt_recent || 2 * recent_sum > idx_recent_sum) &&
> > (!alt_intercepts ||
> > 2 * intercept_sum > idx_intercept_sum)) {
> > - idx = i;
> > - duration_ns = span_ns;
> > + if (!teo_time_ok(span_ns) ||
> > + dev->states_usage[i].disable) {
> > + /*
> > + * The current state is too shallow or
> > + * disabled, so select the first enabled
> > + * deeper state.
> > + */
> > + duration_ns = last_enabled_span_ns;
> > + idx = last_enabled_idx;
> > + } else {
> > + idx = i;
> > + duration_ns = span_ns;
> > + }
> > break;
> > }
>
> Hi Rafael,
>
> I tried the patch and when I disabled idle state 0
> got, very similar to before:
>
> Idle state 0 disabled: FAIL
> Processor: 95 watts
> Idle state 0 entries: 0
> Idle state 1 entries: 65,475,534
> Idle state 2 entries: 333144
> Idle state 3 entries: 65,247,048
>
> However, I accidently left it for about 30 minutes
> and noticed:
>
> Idle state 0 disabled:
> Processor: 83 watts
> Idle state 0 entries: 0
> Idle state 1 entries: 88,706,831
> Idle state 2 entries: 100
> Idle state 3 entries: 662
>
> I went back to unmodified kernel 5.13-rc3 and
Sorry, 5.14-rc3.
> let it run longer with idle state 0 disabled, and
> after 30 minutes it had changed but nowhere
> near as much:
>
> Idle state 0 disabled:
> Processor: 87 watts
> Idle state 0 entries: 0
> Idle state 1 entries: 70,361,020
> Idle state 2 entries: 71219
> Idle state 3 entries: 27,249,975
Addendum: So far the workflow used for this
thread has been event based. If I switch to
a timer based workflow, everything works as
expected for both kernels, 5.14-rc3 unmodified
and modified with the patch from herein.
... Doug
Powered by blists - more mailing lists