linux-kernel - Re: [PATCHv3 1/6] ARM: dts: meson8b: odroidc1: Add usb phy power node

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <2b07b3de-cee5-c570-8fde-6a4c684122d6@baylibre.com>
Date:   Tue, 31 Aug 2021 16:50:04 +0200
From:   Neil Armstrong <narmstrong@...libre.com>
To:     Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Cc:     Anand Moon <linux.amoon@...il.com>, linux-phy@...ts.infradead.org,
        linux-arm-kernel@...ts.infradead.org,
        linux-amlogic@...ts.infradead.org, linux-kernel@...r.kernel.org,
        devicetree@...r.kernel.org,
        Matt Corallo <oc2udbzfd@...tcorallo.com>,
        Rob Herring <robh+dt@...nel.org>,
        Kevin Hilman <khilman@...libre.com>,
        Jerome Brunet <jbrunet@...libre.com>,
        Kishon Vijay Abraham I <kishon@...com>,
        Vinod Koul <vkoul@...nel.org>,
        Emiliano Ingrassia <ingrassia@...genesys.com>,
        Brian Kim <brian.kim@...dkernel.com>
Subject: Re: [PATCHv3 1/6] ARM: dts: meson8b: odroidc1: Add usb phy power node

Hi,

On 30/08/2021 21:37, Martin Blumenstingl wrote:
> Hi Neil,
> 
> On Mon, Aug 30, 2021 at 9:45 AM Neil Armstrong <narmstrong@...libre.com> wrote:
>>
>> Hi,
>>
>> On 17/08/2021 06:15, Anand Moon wrote:
>>> Add missing usb phy power node for usb node fix below warning.
>>> P5V0 regulator supply input voltage range to USB host controller.
>>> As described in the C1+ schematics, GPIO GPIOAO_5 is used to
>>> enable input power to USB ports, set it to Active Low.
>>>
>>> [    1.260772] dwc2 c90c0000.usb: Looking up vbus-supply from device tree
>>> [    1.260784] dwc2 c90c0000.usb: Looking up vbus-supply property in
>>>               mode /soc/usb@...c0000 failed
>>
>> First of all, DT is not here to fix boot message.
> Anand mentioned elsewhere that this is a debug/info message
> 
>> Finally, I looked at the Odroid-C1 schematics and the GPIOAO.BIT5 is an input
>> to the S805, and the PWREN signal is controlled by the USB Hub so this regulator
>> should not be added at all.
> I think there's a misunderstanding because there's two PWREN signals
> with different meanings.
> The PWREN signal for the USB host ports is hard-wired and not
> connected to the SoC at all.
> The PWREN signal for the Micro-USB port (which Anand is adding here)
> is controlled by GPIOAO_5. odroid-c1+_rev0.4_20150615.pdf [0] shows it
> as an input to "USB_OTG" on page 1. "USB_OTG" consists of a power
> switch and the connector itself as shown on page 28.
> 
> Personally I think that the change from Anand itself is good.
> If you feel otherwise then please speak up.

Ok thanks for the clarification, then the change is ok, but not the commit message.

>> Add missing usb phy power node for usb node fix below warning.

is not a good reason for a DT change. A proper reason should be added.

And the commit message doesn't specify the change is for the Micro-USB port,
this should be clarified.

Neil

> As I pointed out three smaller changes I am hoping that Anand will
> re-send the updated patch anyways. At that point he can also add the
> changes from your feedback.
> 
> 
> Best regards,
> Martin
> 
> 
> [0] https://dn.odroid.com/S805/Schematics/odroid-c1+_rev0.4_20150615.pdf
>