| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <AS8PR04MB867694A628587150731B57D48CA89@AS8PR04MB8676.eurprd04.prod.outlook.com>
Date: Tue, 28 Sep 2021 07:09:01 +0000
From: Richard Zhu <hongxing.zhu@....com>
To: Lucas Stach <l.stach@...gutronix.de>,
"kishon@...com" <kishon@...com>,
"vkoul@...nel.org" <vkoul@...nel.org>,
"robh@...nel.org" <robh@...nel.org>,
"galak@...nel.crashing.org" <galak@...nel.crashing.org>,
"shawnguo@...nel.org" <shawnguo@...nel.org>
CC: "linux-phy@...ts.infradead.org" <linux-phy@...ts.infradead.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"kernel@...gutronix.de" <kernel@...gutronix.de>,
dl-linux-imx <linux-imx@....com>
Subject: RE: [PATCH v2 4/4] phy: freescale: pcie: initialize the imx8 pcie
standalone phy driver
> -----Original Message-----
> From: Lucas Stach <l.stach@...gutronix.de>
> Sent: Monday, September 27, 2021 4:43 PM
> To: Richard Zhu <hongxing.zhu@....com>; kishon@...com; vkoul@...nel.org;
> robh@...nel.org; galak@...nel.crashing.org; shawnguo@...nel.org
> Cc: linux-phy@...ts.infradead.org; devicetree@...r.kernel.org;
> linux-arm-kernel@...ts.infradead.org; linux-kernel@...r.kernel.org;
> kernel@...gutronix.de; dl-linux-imx <linux-imx@....com>
> Subject: Re: [PATCH v2 4/4] phy: freescale: pcie: initialize the imx8 pcie
> standalone phy driver
>
> Am Sonntag, dem 26.09.2021 um 15:39 +0800 schrieb Richard Zhu:
> > Add the standalone i.MX8 PCIe PHY driver.
> > Some reset bits should be manipulated between PHY configurations and
> > status check(internal PLL is locked or not).
> > So, do the PHY configuration in the phy_calibrate().
> > And check the PHY is ready or not in the phy_init().
>
> I would really like to see the PCIe controller driver side of this also, as it's hard
> to review standalone. For example I'm not sure if some of those reset bits
> should also be driven from the PHY driver, even if they are currently hooked
> up to the controller driver.
>
> Also I think the IOMUX GPR register handling belongs in the PHY driver, as it's
> configuring the reference clock routing.
>
[Richard Zhu] Sorry to bring inconvenience to you. I would send out the v3
patch-set and the i.MX8MM PCIe controller driver patches after I'm back from the
national holiday tomorrow(about one week).
Although most of the IOMUX GPR bits are related to PHY, but there are some bits are
defined only for controller. For example, the device_type of the controller, the clkreq#
signal control in L1SS, and so on. We can't encapsulate all the GPR bits setting into PHY driver.
So, it's better to let controller driver to handle the general register bits manipulations.
How do you think about that?
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu@....com>
> > ---
> > drivers/phy/freescale/Kconfig | 9 ++
> > drivers/phy/freescale/Makefile | 1 +
> > drivers/phy/freescale/phy-fsl-imx8-pcie.c | 167
> > ++++++++++++++++++++++
> > 3 files changed, 177 insertions(+)
> > create mode 100644 drivers/phy/freescale/phy-fsl-imx8-pcie.c
>
> From what I know, there are several quite different PCIe PHYs used in the
> different i.MX8 variants. I'm not sure if we want to stuff them all into one file.
> I guess we should be more specific here and call this imx8m-phy, or even
> imx8mm-phy.
[Richard Zhu] Good suggestions, I think imx8m-phy is better, since the i.MX8MQ/MM/MP
have the similar architecture of the PCIe PHY implementation.
>
> >
> > diff --git a/drivers/phy/freescale/Kconfig
> > b/drivers/phy/freescale/Kconfig index 320630ffe3cd..da078a676fbc
> > 100644
> > --- a/drivers/phy/freescale/Kconfig
> > +++ b/drivers/phy/freescale/Kconfig
> > @@ -14,3 +14,12 @@ config PHY_MIXEL_MIPI_DPHY
> > help
> > Enable this to add support for the Mixel DSI PHY as found
> > on NXP's i.MX8 family of SOCs.
> > +
> > +config PHY_FSL_IMX8_PCIE
> > + tristate "Freescale i.MX8 PCIE PHY"
> > + depends on OF && HAS_IOMEM
> > + select GENERIC_PHY
> > + default ARCH_MXC
> > + help
> > + Enable this to add support for the PCIE PHY as found on i.MX8
> > + family of SOCs.
> > diff --git a/drivers/phy/freescale/Makefile
> > b/drivers/phy/freescale/Makefile index 1d02e3869b45..9fd467b58621
> > 100644
> > --- a/drivers/phy/freescale/Makefile
> > +++ b/drivers/phy/freescale/Makefile
> > @@ -1,3 +1,4 @@
> > # SPDX-License-Identifier: GPL-2.0-only
> > obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> > obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> > +obj-$(CONFIG_PHY_FSL_IMX8_PCIE) += phy-fsl-imx8-pcie.o
> > diff --git a/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > b/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > new file mode 100644
> > index 000000000000..ff47d6b83686
> > --- /dev/null
> > +++ b/drivers/phy/freescale/phy-fsl-imx8-pcie.c
> > @@ -0,0 +1,167 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2021 NXP
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/delay.h>
> > +#include <linux/module.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <dt-binding/phy/phy-fsl-imx8-pcie.h>
> > +
> > +#define IMX8MM_PCIE_PHY_CMN_REG061 0x184
> > +#define ANA_PLL_CLK_OUT_TO_EXT_IO_EN BIT(0)
> > +#define IMX8MM_PCIE_PHY_CMN_REG062 0x188
> > +#define ANA_PLL_CLK_OUT_TO_EXT_IO_SEL BIT(3)
> > +#define IMX8MM_PCIE_PHY_CMN_REG063 0x18C
> > +#define AUX_PLL_REFCLK_SEL_SYS_PLL GENMASK(7, 6)
> > +#define IMX8MM_PCIE_PHY_CMN_REG064 0x190
> > +#define ANA_AUX_RX_TX_SEL_TX BIT(7)
> > +#define ANA_AUX_RX_TERM_GND_EN BIT(3)
> > +#define ANA_AUX_TX_TERM BIT(2)
> > +#define IMX8MM_PCIE_PHY_CMN_REG065 0x194
> > +#define ANA_AUX_RX_TERM (BIT(7) | BIT(4))
> > +#define ANA_AUX_TX_LVL GENMASK(3, 0)
> > +#define IMX8MM_PCIE_PHY_CMN_REG75 0x1D4
> > +#define PCIE_PHY_CMN_REG75_PLL_DONE 0x3
> > +#define PCIE_PHY_TRSV_REG5 0x414
> > +#define PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D
> > +#define PCIE_PHY_TRSV_REG6 0x418
> > +#define PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF
> > +
> > +struct imx8_pcie_phy {
> > + u32 refclk_pad_mode;
> > + void __iomem *base;
> > + struct clk *clk;
> > + struct phy *phy;
> > +};
> > +
> > +static int imx8_pcie_phy_init(struct phy *phy) {
> > + int ret;
> > + u32 val;
> > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > +
> > + ret = readl_poll_timeout(imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG75,
> > + val, val == PCIE_PHY_CMN_REG75_PLL_DONE,
> > + 10, 20000);
> > + return ret;
> > +}
> > +
> > +static int imx8_pcie_phy_cal(struct phy *phy) {
> > + u32 value, pad_mode;
> > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > +
> > + pad_mode = imx8_phy->refclk_pad_mode;
> > + if (pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT) {
> > + /* Configure the pad as input */
> > + value = readl(imx8_phy->base +
> IMX8MM_PCIE_PHY_CMN_REG061);
> > + writel(value & ~ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061);
> > + } else if (pad_mode == IMX8_PCIE_REFCLK_PAD_OUTPUT) {
> > + /* Configure the PHY to output the refclock via pad */
> > + writel(ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061);
> > + writel(ANA_PLL_CLK_OUT_TO_EXT_IO_SEL,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG062);
> > + writel(AUX_PLL_REFCLK_SEL_SYS_PLL,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG063);
> > + value = ANA_AUX_RX_TX_SEL_TX | ANA_AUX_TX_TERM;
> > + writel(value | ANA_AUX_RX_TERM_GND_EN,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG064);
> > + writel(ANA_AUX_RX_TERM | ANA_AUX_TX_LVL,
> > + imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG065);
> > + }
> > +
> > + /* Tune PHY de-emphasis setting to pass PCIe compliance. */
> > + writel(PCIE_PHY_TRSV_REG5_GEN1_DEEMP,
> > + imx8_phy->base + PCIE_PHY_TRSV_REG5);
> > + writel(PCIE_PHY_TRSV_REG6_GEN2_DEEMP,
> > + imx8_phy->base + PCIE_PHY_TRSV_REG6);
> > +
> > + return 0;
> > +}
> > +
> > +static int imx8_pcie_phy_power_on(struct phy *phy) {
> > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > +
> > + return clk_prepare_enable(imx8_phy->clk);
>
> Do we need to enable this clock when the refclock is supplied externally via
> the pad?
>
[Richard Zhu] Good question. I think this clock is not needed anymore if the refclock is sourced from external OSC.
I just enable the PLL2_100Mhz here, since when internal PLL is used as refclock, the pll2_100Mhz should be turned on.
Shall I remove the setting and just keep the callback for further extend usage(internal PLL used as refclk)?
> > +}
> > +
> > +static int imx8_pcie_phy_power_off(struct phy *phy) {
> > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > +
> > + clk_disable_unprepare(imx8_phy->clk);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct phy_ops imx8_pcie_phy_ops = {
> > + .init = imx8_pcie_phy_init,
> > + .calibrate = imx8_pcie_phy_cal,
> > + .power_on = imx8_pcie_phy_power_on,
> > + .power_off = imx8_pcie_phy_power_off,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static int imx8_pcie_phy_probe(struct platform_device *pdev) {
> > + struct phy_provider *phy_provider;
> > + struct device *dev = &pdev->dev;
> > + struct device_node *np = dev->of_node;
> > + struct imx8_pcie_phy *imx8_phy;
> > + struct resource *res;
> > +
> > + imx8_phy = devm_kzalloc(dev, sizeof(*imx8_phy), GFP_KERNEL);
> > + if (!imx8_phy)
> > + return -ENOMEM;
> > +
> > + /* get PHY refclk pad mode */
> > + of_property_read_u32(np, "fsl,refclk-pad-mode",
> > + &imx8_phy->refclk_pad_mode);
> > +
> > + imx8_phy->clk = devm_clk_get(dev, "phy");
> > + if (IS_ERR(imx8_phy->clk)) {
> > + dev_err(dev, "failed to get imx pcie phy clock\n");
> > + return PTR_ERR(imx8_phy->clk);
> > + }
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + imx8_phy->base = devm_ioremap_resource(dev, res);
> > + if (IS_ERR(imx8_phy->base))
> > + return PTR_ERR(imx8_phy->base);
> > +
> > + imx8_phy->phy = devm_phy_create(dev, NULL, &imx8_pcie_phy_ops);
> > + if (IS_ERR(imx8_phy->phy))
> > + return PTR_ERR(imx8_phy->phy);
> > +
> > + phy_set_drvdata(imx8_phy->phy, imx8_phy);
> > +
> > + phy_provider = devm_of_phy_provider_register(dev,
> > +of_phy_simple_xlate);
> > +
> > + return PTR_ERR_OR_ZERO(phy_provider); }
> > +
> > +static const struct of_device_id imx8_pcie_phy_of_match[] = {
> > + {.compatible = "fsl,imx8mm-pcie-phy",},
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match);
> > +
> > +static struct platform_driver imx8_pcie_phy_driver = {
> > + .probe = imx8_pcie_phy_probe,
> > + .driver = {
> > + .name = "imx8-pcie-phy",
> > + .of_match_table = imx8_pcie_phy_of_match,
> > + }
> > +};
> > +module_platform_driver(imx8_pcie_phy_driver);
> > +
> > +MODULE_DESCRIPTION("FSL IMX8 PCIE PHY driver");
> > +MODULE_LICENSE("GPL");
>
Powered by blists - more mailing lists