Message-Id: <20211005135400.788058-3-Jerome.Pouiller@silabs.com>
Date:   Tue,  5 Oct 2021 15:53:38 +0200
From:   Jerome Pouiller <Jerome.Pouiller@...abs.com>
To:     linux-wireless@...r.kernel.org, netdev@...r.kernel.org,
        Kalle Valo <kvalo@...eaurora.org>
Cc:     devel@...verdev.osuosl.org, linux-kernel@...r.kernel.org,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        "David S . Miller" <davem@...emloft.net>,
        devicetree@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
        linux-mmc@...r.kernel.org,
        Pali Rohár <pali@...nel.org>,
        Ulf Hansson <ulf.hansson@...aro.org>,
        Jérôme Pouiller 
        <jerome.pouiller@...abs.com>
Subject: [PATCH v8 02/24] dt-bindings: introduce silabs,wfx.yaml

From: Jérôme Pouiller <jerome.pouiller@...abs.com>

Prepare the inclusion of the wfx driver in the kernel.

Signed-off-by: Jérôme Pouiller <jerome.pouiller@...abs.com>
---
 .../bindings/net/wireless/silabs,wfx.yaml     | 137 ++++++++++++++++++
 1 file changed, 137 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml

diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
new file mode 100644
index 000000000000..6dc30eb5661b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020, Silicon Laboratories, Inc.
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Labs WFxxx devicetree bindings
+
+maintainers:
+  - Jérôme Pouiller <jerome.pouiller@...abs.com>
+
+description: >
+  Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
+  from the WFxxx series is the WF200 described here:
+     https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
+
+  The WF200 can be connected via SPI or via SDIO.
+
+  For SDIO:
+
+    Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
+    sufficient for the SDIO devices).
+
+    It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
+    it, you may encounter issues during reboot. The mmc-pwrseq should be
+    compatible with mmc-pwrseq-simple. Please consult
+    Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more
+    information.
+
+  For SPI:
+
+    In add of the properties below, please consult
+    Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
+    related properties.
+
+properties:
+  compatible: Should be one of:
+    - "silabs,wf200": Chip alone without antenna
+    - "silabs,brd4001a": Development board with a WF200 and an antenna
+    - "silabs,brd8022a": Development board with a WF200 and an antenna
+    - "silabs,brd8023a": Development board with a WF200 and an antenna
+
+  reg:
+    description:
+      When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
+      the chip select address of the device as defined in the SPI devices
+      bindings.
+    maxItems: 1
+
+  spi-max-frequency: true
+
+  interrupts:
+    description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and
+      IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When
+      SPI is used, this property is required. When SDIO is used, the "in-band"
+      interrupt provided by the SDIO bus is used unless an interrupt is defined
+      in the Device Tree.
+    maxItems: 1
+
+  reset-gpios:
+    description: (SPI only) Phandle of gpio that will be used to reset chip
+      during probe. Without this property, you may encounter issues with warm
+      boot. (For legacy purpose, the gpio in inverted when compatible ==
+      "silabs,wfx-spi")
+
+      For SDIO, the reset gpio should declared using a mmc-pwrseq.
+    maxItems: 1
+
+  wakeup-gpios:
+    description: Phandle of gpio that will be used to wake-up chip. Without this
+      property, driver will disable most of power saving features.
+    maxItems: 1
+
+  silabs,antenna-config-file:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: Use an alternative file for antenna configuration (aka
+      "Platform Data Set" in Silabs jargon). Default depends of "compatible"
+      string. For "silabs,wf200", the default is 'wf200.pds'.
+
+  local-mac-address: true
+
+  mac-address: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        wifi@0 {
+            compatible = "silabs,wf200";
+            pinctrl-names = "default";
+            pinctrl-0 = <&wfx_irq &wfx_gpios>;
+            reg = <0>;
+            interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>;
+            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+            spi-max-frequency = <42000000>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    wfx_pwrseq: wfx_pwrseq {
+        compatible = "mmc-pwrseq-simple";
+        pinctrl-names = "default";
+        pinctrl-0 = <&wfx_reset>;
+        reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+    };
+
+    mmc0 {
+        mmc-pwrseq = <&wfx_pwrseq>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        wifi@1 {
+            compatible = "silabs,wf200";
+            pinctrl-names = "default";
+            pinctrl-0 = <&wfx_wakeup>;
+            reg = <1>;
+            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+        };
+    };
+...
-- 
2.33.0

Powered by blists - more mailing lists