| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20211009104419.8811-1-straube.linux@gmail.com>
Date: Sat, 9 Oct 2021 12:44:17 +0200
From: Michael Straube <straube.linux@...il.com>
To: gregkh@...uxfoundation.org
Cc: Larry.Finger@...inger.net, phil@...lpotter.co.uk,
linux-staging@...ts.linux.dev, linux-kernel@...r.kernel.org,
Michael Straube <straube.linux@...il.com>
Subject: [PATCH 1/3] staging: r8188eu: remove unused macros and defines from rtl8188e_hal.h
Remove unused macros and defines from rtl8188e_hal.h.
Signed-off-by: Michael Straube <straube.linux@...il.com>
---
.../staging/r8188eu/include/rtl8188e_hal.h | 55 -------------------
1 file changed, 55 deletions(-)
diff --git a/drivers/staging/r8188eu/include/rtl8188e_hal.h b/drivers/staging/r8188eu/include/rtl8188e_hal.h
index 66ecd3c3ac13..5fdee1c6299c 100644
--- a/drivers/staging/r8188eu/include/rtl8188e_hal.h
+++ b/drivers/staging/r8188eu/include/rtl8188e_hal.h
@@ -19,29 +19,10 @@
#include "odm_precomp.h"
-/* Fw Array */
-#define Rtl8188E_FwImageArray Rtl8188EFwImgArray
-#define Rtl8188E_FWImgArrayLength Rtl8188EFWImgArrayLength
-
-#define RTL8188E_FW_UMC_IMG "rtl8188E\\rtl8188efw.bin"
-#define RTL8188E_PHY_REG "rtl8188E\\PHY_REG_1T.txt"
-#define RTL8188E_PHY_RADIO_A "rtl8188E\\radio_a_1T.txt"
-#define RTL8188E_PHY_RADIO_B "rtl8188E\\radio_b_1T.txt"
-#define RTL8188E_AGC_TAB "rtl8188E\\AGC_TAB_1T.txt"
-#define RTL8188E_PHY_MACREG "rtl8188E\\MAC_REG.txt"
-#define RTL8188E_PHY_REG_PG "rtl8188E\\PHY_REG_PG.txt"
-#define RTL8188E_PHY_REG_MP "rtl8188E\\PHY_REG_MP.txt"
-
/* RTL8188E Power Configuration CMDs for USB/SDIO interfaces */
#define Rtl8188E_NIC_PWR_ON_FLOW rtl8188E_power_on_flow
-#define Rtl8188E_NIC_RF_OFF_FLOW rtl8188E_radio_off_flow
#define Rtl8188E_NIC_DISABLE_FLOW rtl8188E_card_disable_flow
-#define Rtl8188E_NIC_ENABLE_FLOW rtl8188E_card_enable_flow
-#define Rtl8188E_NIC_SUSPEND_FLOW rtl8188E_suspend_flow
-#define Rtl8188E_NIC_RESUME_FLOW rtl8188E_resume_flow
-#define Rtl8188E_NIC_PDN_FLOW rtl8188E_hwpdn_flow
#define Rtl8188E_NIC_LPS_ENTER_FLOW rtl8188E_enter_lps_flow
-#define Rtl8188E_NIC_LPS_LEAVE_FLOW rtl8188E_leave_lps_flow
#define DRVINFO_SZ 4 /* unit is 8bytes */
#define PageNum_128(_Len) (u32)(((_Len)>>7) + ((_Len) & 0x7F ? 1 : 0))
@@ -49,7 +30,6 @@
/* download firmware related data structure */
#define FW_8188E_SIZE 0x4000 /* 16384,16k */
#define FW_8188E_START_ADDRESS 0x1000
-#define FW_8188E_END_ADDRESS 0x1FFF /* 0x5FFF */
#define MAX_PAGE_SIZE 4096 /* @ page : 4k bytes */
@@ -108,11 +88,6 @@ enum usb_rx_agg_mode {
0x2400 /* 9k for 88E nornal chip , MaxRxBuff=10k-max(TxReportSize(64*8),
* WOLPattern(16*24)) */
-#define MAX_TX_REPORT_BUFFER_SIZE 0x0400 /* 1k */
-
-/* BK, BE, VI, VO, HCCA, MANAGEMENT, COMMAND, HIGH, BEACON. */
-#define MAX_TX_QUEUE 9
-
#define TX_SELE_HQ BIT(0) /* High Queue */
#define TX_SELE_LQ BIT(1) /* Low Queue */
#define TX_SELE_NQ BIT(2) /* Normal Queue */
@@ -134,11 +109,6 @@ enum usb_rx_agg_mode {
#define WMM_NORMAL_TX_PAGE_BOUNDARY_88E \
(WMM_NORMAL_TX_TOTAL_PAGE_NUMBER + 1) /* 0xA9 */
-/* Chip specific */
-#define CHIP_BONDING_IDENTIFIER(_value) (((_value)>>22)&0x3)
-#define CHIP_BONDING_92C_1T2R 0x1
-#define CHIP_BONDING_88C_USB_MCARD 0x2
-#define CHIP_BONDING_88C_USB_HP 0x1
#include "HalVerDef.h"
#include "hal_com.h"
@@ -168,29 +138,11 @@ struct txpowerinfo24g {
};
#define EFUSE_REAL_CONTENT_LEN 512
-#define EFUSE_MAX_SECTION 16
-#define EFUSE_IC_ID_OFFSET 506 /* For some inferior IC purpose*/
#define AVAILABLE_EFUSE_ADDR(addr) (addr < EFUSE_REAL_CONTENT_LEN)
-/* To prevent out of boundary programming case, */
-/* leave 1byte and program full section */
-/* 9bytes + 1byt + 5bytes and pre 1byte. */
-/* For worst case: */
-/* | 1byte|----8bytes----|1byte|--5bytes--| */
-/* | | Reserved(14bytes) | */
-
-/* PG data exclude header, dummy 6 bytes frome CP test and reserved 1byte. */
-#define EFUSE_OOB_PROTECT_BYTES 15
-
-#define HWSET_MAX_SIZE_88E 512
#define EFUSE_REAL_CONTENT_LEN_88E 256
#define EFUSE_MAP_LEN_88E 512
-#define EFUSE_MAP_LEN EFUSE_MAP_LEN_88E
#define EFUSE_MAX_SECTION_88E 64
-#define EFUSE_MAX_WORD_UNIT_88E 4
-#define EFUSE_IC_ID_OFFSET_88E 506
-#define AVAILABLE_EFUSE_ADDR_88E(addr) \
- (addr < EFUSE_REAL_CONTENT_LEN_88E)
/* To prevent out of boundary programming case, leave 1byte and program
* full section */
/* 9bytes + 1byt + 5bytes and pre 1byte. */
@@ -198,12 +150,6 @@ struct txpowerinfo24g {
/* | 2byte|----8bytes----|1byte|--7bytes--| 92D */
/* PG data exclude header, dummy 7 bytes frome CP test and reserved 1byte. */
#define EFUSE_OOB_PROTECT_BYTES_88E 18
-#define EFUSE_PROTECT_BYTES_BANK_88E 16
-
-/* EFUSE for BT definition */
-#define EFUSE_BT_REAL_CONTENT_LEN 1536 /* 512*3 */
-#define EFUSE_BT_MAP_LEN 1024 /* 1k bytes */
-#define EFUSE_BT_MAX_SECTION 128 /* 1024/8 */
#define EFUSE_PROTECT_BYTES_BANK 16
@@ -367,7 +313,6 @@ struct hal_data_8188e {
#define GET_HAL_DATA(__pAdapter) \
((struct hal_data_8188e *)((__pAdapter)->HalData))
-#define GET_RF_TYPE(priv) (GET_HAL_DATA(priv)->rf_type)
/* rtl8188e_hal_init.c */
s32 rtl8188e_FirmwareDownload(struct adapter *padapter);
--
2.33.0
Powered by blists - more mailing lists