lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite for Android: free password hash cracker in your pocket
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date:   Fri, 15 Oct 2021 17:26:03 -0500
From:   Adam Ford <aford173@...il.com>
To:     Laurent Pinchart <laurent.pinchart@...asonboard.com>
Cc:     arm-soc <linux-arm-kernel@...ts.infradead.org>,
        Adam Ford-BE <aford@...conembedded.com>,
        Rob Herring <robh+dt@...nel.org>,
        Shawn Guo <shawnguo@...nel.org>,
        Sascha Hauer <s.hauer@...gutronix.de>,
        Pengutronix Kernel Team <kernel@...gutronix.de>,
        Fabio Estevam <festevam@...il.com>,
        NXP Linux Team <linux-imx@....com>,
        devicetree <devicetree@...r.kernel.org>,
        Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH] arm64: dts: imx8mm: Add CSI nodes

On Thu, Oct 14, 2021 at 4:16 PM Laurent Pinchart
<laurent.pinchart@...asonboard.com> wrote:
>
> Hi Adam,
>
> On Thu, Oct 14, 2021 at 03:32:33PM -0500, Adam Ford wrote:
> > On Wed, Oct 13, 2021 at 9:52 PM Adam Ford <aford173@...il.com> wrote:
> > >
> > > There is a csi bridge and csis interface that tie together
> > > to allow csi2 capture.
> > >
> > > Signed-off-by: Adam Ford <aford173@...il.com>
> >
> > Laurent,
> >
> > Since you did some work to make the csis functional on the imx8mm, I
> > was hoping you might have some insights.  Please see below:
> >
> > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > index c2f3f118f82e..8a8a5d0a4a1e 100644
> > > --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > @@ -1068,6 +1068,22 @@ aips4: bus@...00000 {
> > >                         #size-cells = <1>;
> > >                         ranges = <0x32c00000 0x32c00000 0x400000>;
> > >
> > > +                       csi: csi@...20000 {
> > > +                               compatible = "fsl,imx7-csi";
>
> This should be
>
>         compatible = "fsl,imx8mm-csi", "fsl,imx7-csi";;
>
> > > +                               reg = <0x32e20000 0x1000>;
> > > +                               interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> > > +                               clocks = <&clk IMX8MM_CLK_CSI1_ROOT>;
> > > +                               clock-names = "mclk";
> > > +                               power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_CSI_BRIDGE>;
> > > +                               status = "disabled";
> > > +
> > > +                               port {
> > > +                                       csi_in: endpoint {
> > > +                                               remote-endpoint = <&imx8mm_mipi_csi_out>;
> > > +                                       };
> > > +                               };
> > > +                       };
> > > +
> > >                         disp_blk_ctrl: blk-ctrl@...28000 {
> > >                                 compatible = "fsl,imx8mm-disp-blk-ctrl", "syscon";
> > >                                 reg = <0x32e28000 0x100>;
> > > @@ -1095,6 +1111,41 @@ disp_blk_ctrl: blk-ctrl@...28000 {
> > >                                 #power-domain-cells = <1>;
> > >                         };
> > >
> > > +                       mipi_csi2: mipi-csi@...30000 {
> > > +                               compatible = "fsl,imx8mm-mipi-csi2";
> > > +                               reg = <0x32e30000 0x1000>;
> > > +                               interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> > > +                               clock-frequency = <333000000>;
> > > +                               clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>,
> > > +                                        <&clk IMX8MM_CLK_CSI1_ROOT>,
> > > +                                        <&clk IMX8MM_CLK_CSI1_PHY_REF>,
> > > +                                        <&clk IMX8MM_CLK_DISP_AXI_ROOT>;
> >
> > When comparing clock parents and the clock rates to one of NXP's
> > kernels, it appears we need assigned-clocks and assigned-clock-parents
> > to allow the CSI1 clocks to run fast enough.
> >
> > assigned-clocks = <&clk IMX8MM_CLK_CSI1_PHY_REF>,
> >   <&clk IMX8MM_CLK_CSI1_CORE>,
> >   <&clk IMX8MM_CLK_CSI1_ROOT>,
> >   <&clk IMX8MM_CLK_CSI1_ESC>;
> > assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
> >   <&clk IMX8MM_SYS_PLL2_1000M>,
> >   <&clk IMX8MM_CLK_CSI1_CORE>,
> >   <&clk IMX8MM_SYS_PLL1_800M>;
> >
> > However, even with this, I am attempting to capture.  While I can get
> > the pipeline enabled, when I try to capture a file, I get no data.  i
> > can use control-c to exit gstreamer, so I know the kernel didn't hang.
> > I don't get errors, but I don't get data either.
> >
> > Any ideas if what/if any other clock entries might be missing?
>
> Have you tried looking at the error interrupt counters to see if the
> CSI-2 bus side operates as expected ? I'd start there before blaming the
> clocks. Note that the issue could also be in the CSI bridge.

I am not seeing interrupts on either the CSI, mipi-csi, or err:

 54:          0          0          0          0     GICv3  48 Level     csi
 55:          0          0          0          0     GICv3  49 Level
  32e30000.mipi-csi
Err:          0


>
> I've had issues capturing from one particular sensor on an i.MX8MM
> board, where I would get images, but with heavy corruption. The problem
> was solved by chance when trying a different SPL binary. I need to

I wonder if the issue was related to different versions of ATF, and
depending on the power domain controls used, it could have been using
ATF to set the power domains.
I've had issues in the past too, but I have tried a couple different
binaries, and I am not seeing a change in behavior.

> investigate the differences there, and possibly update the driver
> accordingly. It may or may not be related to your issue.
>
> Apart from the compatible string issue mentioned above, the bindings
> match what I am using, so, with the compatible string fixed,
>

Out of curiosity, I noticed the default csi clock parents point to a
24MHz clock, but the csi-2 interface wants to set the clock to 333MHz.
Any chance you could share your clk_summary?

> Reviewed-by: Laurent Pinchart <laurent.pinchart@...asonboard.com>

Thanks for the review
>
> > > +                               clock-names = "pclk", "wrap", "phy", "axi";
> > > +                               power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_MIPI_CSI>;
> > > +                               status = "disabled";
> > > +
> > > +                               ports {
> > > +                                       #address-cells = <1>;
> > > +                                       #size-cells = <0>;
> > > +
> > > +                                       port@0 {
> > > +                                               reg = <0>;
> > > +
> > > +                                               imx8mm_mipi_csi_in: endpoint {
> > > +                                               };
> > > +                                       };
> > > +
> > > +                                       port@1 {
> > > +                                               reg = <1>;
> > > +
> > > +                                               imx8mm_mipi_csi_out: endpoint {
> > > +                                                       remote-endpoint = <&csi_in>;
> > > +                                               };
> > > +                                       };
> > > +                               };
> > > +                       };
> > > +
> > > +
> > >                         usbotg1: usb@...40000 {
> > >                                 compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
> > >                                 reg = <0x32e40000 0x200>;
>
> --
> Regards,
>
> Laurent Pinchart

Powered by blists - more mailing lists