| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAA8EJpqGbiy_d1_RUoPiT0Jz0CgC5WaekkuJFXyzU7z7rkZChw@mail.gmail.com>
Date: Sat, 16 Oct 2021 19:36:45 +0300
From: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
To: Bjorn Andersson <bjorn.andersson@...aro.org>
Cc: Kishon Vijay Abraham I <kishon@...com>,
Vinod Koul <vkoul@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
"open list:DRM DRIVER FOR MSM ADRENO GPU"
<linux-arm-msm@...r.kernel.org>, linux-phy@...ts.infradead.org,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@...r.kernel.org>,
open list <linux-kernel@...r.kernel.org>,
Abhinav Kumar <abhinavk@...eaurora.org>,
Stephen Boyd <sboyd@...nel.org>
Subject: Re: [PATCH v2 2/2] phy: qcom: Introduce new eDP PHY driver
On Sat, 16 Oct 2021 at 01:11, Bjorn Andersson
<bjorn.andersson@...aro.org> wrote:
>
> Many recent Qualcomm platforms comes with native DP and eDP support.
> This consists of a controller in the MDSS and a QMP-like PHY.
>
> While similar to the well known QMP block, the eDP PHY only has TX lanes
> and the programming sequences are slightly different. Rather than
> continuing the trend of parameterize the QMP driver to pieces, this
> introduces the support as a new driver.
>
> The registration of link and pixel clocks are borrowed from the QMP
> driver. The non-DP link frequencies are omitted for now.
>
> The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
> the prior is supported for now.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@...aro.org>
> ---
>
> Changes since v1:
> - Fixed copy paste issue in register defines, causing a off-by-4 on the AUX
> registers
> - Cleaned out unused registers
> - Sorted Kconfig and Makefile
> - Using devm_of_clk_add_hw_provider()
>
> We discussed about moving the DP pieces to some common helper, to be shared
> with the main QMP driver, but I haven't yet figured out a good structure for
> this.
>
> Given that such refactoring would be a really good idea in itself, perhaps as
> we make the DP driver orientation and mux aware, I was hoping we could take the
> duplication in this driver for now and then circle back and clean the two
> drivers up together.
>
> drivers/phy/qualcomm/Kconfig | 10 +
> drivers/phy/qualcomm/Makefile | 1 +
> drivers/phy/qualcomm/phy-qcom-edp.c | 715 ++++++++++++++++++++++++++++
> 3 files changed, 726 insertions(+)
> create mode 100644 drivers/phy/qualcomm/phy-qcom-edp.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index 7f6fcb8ec5ba..5c98850f5a36 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -18,6 +18,16 @@ config PHY_QCOM_APQ8064_SATA
> depends on OF
> select GENERIC_PHY
>
> +config PHY_QCOM_EDP
> + tristate "Qualcomm eDP PHY driver"
> + depends on ARCH_QCOM || COMPILE_TEST
> + depends on OF
> + depends on COMMON_CLK
> + select GENERIC_PHY
> + help
> + Enable this driver to support the Qualcomm eDP PHY found in various
> + Qualcomm chipsets.
> +
> config PHY_QCOM_IPQ4019_USB
> tristate "Qualcomm IPQ4019 USB PHY driver"
> depends on OF && (ARCH_QCOM || COMPILE_TEST)
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index 47acbd7daa3a..e9e3b1a4dbb0 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -1,6 +1,7 @@
> # SPDX-License-Identifier: GPL-2.0
> obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o
> obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
> +obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o
> obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
> obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
> new file mode 100644
> index 000000000000..8ce9509fd989
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c
> @@ -0,0 +1,715 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2017, 2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2021, Linaro Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +#define DP_PHY_PD_CTL_PWRDN 0x001
> +#define DP_PHY_PD_CTL_PSR_PWRDN 0x002
> +#define DP_PHY_PD_CTL_AUX_PWRDN 0x004
> +#define DP_PHY_PD_CTL_LANE_0_1_PWRDN 0x008
> +#define DP_PHY_PD_CTL_LANE_2_3_PWRDN 0x010
> +#define DP_PHY_PD_CTL_PLL_PWRDN 0x020
> +#define DP_PHY_PD_CTL_DP_CLAMP_EN 0x040
> +
> +#define DP_PHY_CFG 0x0010
> +#define DP_PHY_CFG_1 0x0014
> +#define DP_PHY_PD_CTL 0x001c
> +#define DP_PHY_MODE 0x0020
> +
> +#define DP_PHY_AUX_CFG0 0x0024
> +#define DP_PHY_AUX_CFG1 0x0028
> +#define DP_PHY_AUX_CFG2 0x002C
> +#define DP_PHY_AUX_CFG3 0x0030
> +#define DP_PHY_AUX_CFG4 0x0034
> +#define DP_PHY_AUX_CFG5 0x0038
> +#define DP_PHY_AUX_CFG6 0x003C
> +#define DP_PHY_AUX_CFG7 0x0040
> +#define DP_PHY_AUX_CFG8 0x0044
> +#define DP_PHY_AUX_CFG9 0x0048
> +
> +#define DP_PHY_VCO_DIV 0x0074
> +#define DP_PHY_TX0_TX1_LANE_CTL 0x007c
> +#define DP_PHY_TX2_TX3_LANE_CTL 0x00a0
> +
> +#define DP_PHY_STATUS 0x00e0
> +
> +/* Tx registers */
> +#define TXn_CLKBUF_ENABLE 0x0000
> +#define TXn_TX_EMP_POST1_LVL 0x0004
> +
> +#define TXn_TX_DRV_LVL 0x0014
> +#define TXn_TX_DRV_LVL_OFFSET 0x0018
> +#define TXn_RESET_TSYNC_EN 0x001c
> +#define TXn_LDO_CONFIG 0x0084
> +#define TXn_TX_BAND 0x0028
> +
> +#define TXn_RES_CODE_LANE_OFFSET_TX0 0x0044
> +#define TXn_RES_CODE_LANE_OFFSET_TX1 0x0048
> +
> +#define TXn_TRANSCEIVER_BIAS_EN 0x0054
> +#define TXn_HIGHZ_DRVR_EN 0x0058
> +#define TXn_TX_POL_INV 0x005c
> +#define TXn_LANE_MODE_1 0x0064
> +
> +#define TXn_TRAN_DRVR_EMP_EN 0x0078
> +
> +/* PLL register offset */
> +#define QSERDES_COM_BG_TIMER 0x000c
> +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x0044
> +#define QSERDES_COM_CLK_ENABLE1 0x0048
> +#define QSERDES_COM_SYS_CLK_CTRL 0x004c
> +#define QSERDES_COM_SYSCLK_BUF_ENABLE 0x0050
> +#define QSERDES_COM_PLL_IVCO 0x0058
> +
> +#define QSERDES_COM_CP_CTRL_MODE0 0x0074
> +#define QSERDES_COM_PLL_RCTRL_MODE0 0x007c
> +#define QSERDES_COM_PLL_CCTRL_MODE0 0x0084
> +#define QSERDES_COM_SYSCLK_EN_SEL 0x0094
> +#define QSERDES_COM_RESETSM_CNTRL 0x009c
> +#define QSERDES_COM_LOCK_CMP_EN 0x00a4
> +#define QSERDES_COM_LOCK_CMP1_MODE0 0x00ac
> +#define QSERDES_COM_LOCK_CMP2_MODE0 0x00b0
> +
> +#define QSERDES_COM_DEC_START_MODE0 0x00bc
> +#define QSERDES_COM_DIV_FRAC_START1_MODE0 0x00cc
> +#define QSERDES_COM_DIV_FRAC_START2_MODE0 0x00d0
> +#define QSERDES_COM_DIV_FRAC_START3_MODE0 0x00d4
> +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x00ec
> +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x00f0
> +#define QSERDES_COM_VCO_TUNE_CTRL 0x0108
> +#define QSERDES_COM_VCO_TUNE_MAP 0x010c
> +#define QSERDES_COM_VCO_TUNE1_MODE0 0x0110
> +#define QSERDES_COM_VCO_TUNE2_MODE0 0x0114
> +#define QSERDES_COM_CMN_STATUS 0x0140
> +
> +#define QSERDES_COM_CLK_SEL 0x0154
> +#define QSERDES_COM_HSCLK_SEL 0x0158
> +
> +#define QSERDES_COM_CORECLK_DIV_MODE0 0x0168
> +
> +#define QSERDES_COM_CORE_CLK_EN 0x0174
> +#define QSERDES_COM_C_READY_STATUS 0x0178
> +#define QSERDES_COM_CMN_CONFIG 0x017c
> +
> +#define QSERDES_COM_SVS_MODE_CLK_SEL 0x0184
> +
> +#define QSERDES_COM_SSC_EN_CENTER 0x0010
> +#define QSERDES_COM_SSC_ADJ_PER1 0x0014
> +#define QSERDES_COM_SSC_PER1 0x001c
> +#define QSERDES_COM_SSC_PER2 0x0020
> +#define QSERDES_COM_SSC_STEP_SIZE1_MODE0 0x0024
> +#define QSERDES_COM_SSC_STEP_SIZE2_MODE0 0x0028
I think we might want to use register definitions from phy-qcom-qmp.h,
so that it would be obvious, which generations are handled by the
driver.
> +
> +struct qcom_edp {
> + struct device *dev;
> +
> + struct phy *phy;
> +
> + void __iomem *edp;
> + void __iomem *tx0;
> + void __iomem *tx1;
> + void __iomem *pll;
> +
> + struct clk_hw dp_link_hw;
> + struct clk_hw dp_pixel_hw;
> +
> + struct phy_configure_opts_dp dp_opts;
> +
> + struct clk_bulk_data clks[2];
> + struct regulator_bulk_data supplies[2];
> +};
> +
> +static int qcom_edp_phy_init(struct phy *phy)
> +{
> + struct qcom_edp *edp = phy_get_drvdata(phy);
> + int ret;
> +
> + ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies);
> + if (ret)
> + return ret;
> +
> + ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks);
> + if (ret)
> + goto out_disable_supplies;
> +
> + writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> + DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> + edp->edp + DP_PHY_PD_CTL);
> +
> + writel(0x17, edp->pll + QSERDES_COM_BIAS_EN_CLKBUFLR_EN);
> +
> + writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
> + msleep(20);
> +
> + writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> + DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
> + DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> + edp->edp + DP_PHY_PD_CTL);
> +
> + writel(0x00, edp->edp + DP_PHY_AUX_CFG0);
> + writel(0x13, edp->edp + DP_PHY_AUX_CFG1);
> + writel(0x24, edp->edp + DP_PHY_AUX_CFG2);
> + writel(0x00, edp->edp + DP_PHY_AUX_CFG3);
> + writel(0x0a, edp->edp + DP_PHY_AUX_CFG4);
> + writel(0x26, edp->edp + DP_PHY_AUX_CFG5);
> + writel(0x0a, edp->edp + DP_PHY_AUX_CFG6);
> + writel(0x03, edp->edp + DP_PHY_AUX_CFG7);
> + writel(0x37, edp->edp + DP_PHY_AUX_CFG8);
> + writel(0x03, edp->edp + DP_PHY_AUX_CFG9);
> +
> + writel(0x1f, edp->edp + 0x58);
> +
> + msleep(20);
> +
> + return 0;
> +
> +out_disable_supplies:
> + regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
> +
> + return ret;
> +}
> +
> +static int qcom_edp_phy_configure(struct phy *phy, union phy_configure_opts *opts)
> +{
> + const struct phy_configure_opts_dp *dp_opts = &opts->dp;
> + struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> + memcpy(&edp->dp_opts, dp_opts, sizeof(*dp_opts));
> +
> + return 0;
> +}
> +
> +static int qcom_edp_configure_ssc(struct qcom_edp *edp)
> +{
> + const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> + u32 step1;
> + u32 step2;
> +
> + switch (dp_opts->link_rate) {
> + case 1620:
> + case 2700:
> + case 8100:
> + step1 = 0x45;
> + step2 = 0x06;
> + break;
> + case 5400:
> + step1 = 0x5c;
> + step2 = 0x08;
> + break;
> + default:
> + /* Other link rates aren't supported */
> + return -EINVAL;
> + }
> +
> + writel(0x01, edp->pll + QSERDES_COM_SSC_EN_CENTER);
> + writel(0x00, edp->pll + QSERDES_COM_SSC_ADJ_PER1);
> + writel(0x36, edp->pll + QSERDES_COM_SSC_PER1);
> + writel(0x01, edp->pll + QSERDES_COM_SSC_PER2);
> + writel(step1, edp->pll + QSERDES_COM_SSC_STEP_SIZE1_MODE0);
> + writel(step2, edp->pll + QSERDES_COM_SSC_STEP_SIZE2_MODE0);
> +
> + return 0;
> +}
> +
> +static int qcom_edp_configure_pll(struct qcom_edp *edp)
> +{
> + const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> + u32 div_frac_start2_mode0;
> + u32 div_frac_start3_mode0;
> + u32 dec_start_mode0;
> + u32 lock_cmp1_mode0;
> + u32 lock_cmp2_mode0;
> + u32 hsclk_sel;
> +
> + switch (dp_opts->link_rate) {
> + case 1620:
> + hsclk_sel = 0x5;
> + dec_start_mode0 = 0x69;
> + div_frac_start2_mode0 = 0x80;
> + div_frac_start3_mode0 = 0x07;
> + lock_cmp1_mode0 = 0x6f;
> + lock_cmp2_mode0 = 0x08;
> + break;
> + case 2700:
> + hsclk_sel = 0x3;
> + dec_start_mode0 = 0x69;
> + div_frac_start2_mode0 = 0x80;
> + div_frac_start3_mode0 = 0x07;
> + lock_cmp1_mode0 = 0x0f;
> + lock_cmp2_mode0 = 0x0e;
> + break;
> + case 5400:
> + hsclk_sel = 0x1;
> + dec_start_mode0 = 0x8c;
> + div_frac_start2_mode0 = 0x00;
> + div_frac_start3_mode0 = 0x0a;
> + lock_cmp1_mode0 = 0x1f;
> + lock_cmp2_mode0 = 0x1c;
> + break;
> + case 8100:
> + hsclk_sel = 0x0;
> + dec_start_mode0 = 0x69;
> + div_frac_start2_mode0 = 0x80;
> + div_frac_start3_mode0 = 0x07;
> + lock_cmp1_mode0 = 0x2f;
> + lock_cmp2_mode0 = 0x2a;
> + break;
> + default:
> + /* Other link rates aren't supported */
> + return -EINVAL;
> + }
> +
> + writel(0x01, edp->pll + QSERDES_COM_SVS_MODE_CLK_SEL);
> + writel(0x0b, edp->pll + QSERDES_COM_SYSCLK_EN_SEL);
> + writel(0x02, edp->pll + QSERDES_COM_SYS_CLK_CTRL);
> + writel(0x0c, edp->pll + QSERDES_COM_CLK_ENABLE1);
> + writel(0x06, edp->pll + QSERDES_COM_SYSCLK_BUF_ENABLE);
> + writel(0x30, edp->pll + QSERDES_COM_CLK_SEL);
> + writel(hsclk_sel, edp->pll + QSERDES_COM_HSCLK_SEL);
> + writel(0x0f, edp->pll + QSERDES_COM_PLL_IVCO);
> + writel(0x08, edp->pll + QSERDES_COM_LOCK_CMP_EN);
> + writel(0x36, edp->pll + QSERDES_COM_PLL_CCTRL_MODE0);
> + writel(0x16, edp->pll + QSERDES_COM_PLL_RCTRL_MODE0);
> + writel(0x06, edp->pll + QSERDES_COM_CP_CTRL_MODE0);
> + writel(dec_start_mode0, edp->pll + QSERDES_COM_DEC_START_MODE0);
> + writel(0x00, edp->pll + QSERDES_COM_DIV_FRAC_START1_MODE0);
> + writel(div_frac_start2_mode0, edp->pll + QSERDES_COM_DIV_FRAC_START2_MODE0);
> + writel(div_frac_start3_mode0, edp->pll + QSERDES_COM_DIV_FRAC_START3_MODE0);
> + writel(0x02, edp->pll + QSERDES_COM_CMN_CONFIG);
> + writel(0x3f, edp->pll + QSERDES_COM_INTEGLOOP_GAIN0_MODE0);
> + writel(0x00, edp->pll + QSERDES_COM_INTEGLOOP_GAIN1_MODE0);
> + writel(0x00, edp->pll + QSERDES_COM_VCO_TUNE_MAP);
> + writel(lock_cmp1_mode0, edp->pll + QSERDES_COM_LOCK_CMP1_MODE0);
> + writel(lock_cmp2_mode0, edp->pll + QSERDES_COM_LOCK_CMP2_MODE0);
> +
> + writel(0x0a, edp->pll + QSERDES_COM_BG_TIMER);
> + writel(0x14, edp->pll + QSERDES_COM_CORECLK_DIV_MODE0);
> + writel(0x00, edp->pll + QSERDES_COM_VCO_TUNE_CTRL);
> + writel(0x17, edp->pll + QSERDES_COM_BIAS_EN_CLKBUFLR_EN);
> + writel(0x0f, edp->pll + QSERDES_COM_CORE_CLK_EN);
> + writel(0xa0, edp->pll + QSERDES_COM_VCO_TUNE1_MODE0);
> + writel(0x03, edp->pll + QSERDES_COM_VCO_TUNE2_MODE0);
> +
> + return 0;
> +}
> +
> +static int qcom_edp_set_vco_div(struct qcom_edp *edp)
> +{
> + const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> + unsigned long pixel_freq;
> + u32 vco_div;
> +
> + switch (dp_opts->link_rate) {
> + case 1620:
> + vco_div = 0x1;
> + pixel_freq = 1620000000UL / 2;
> + break;
> + case 2700:
> + vco_div = 0x1;
> + pixel_freq = 2700000000UL / 2;
> + break;
> + case 5400:
> + vco_div = 0x2;
> + pixel_freq = 5400000000UL / 4;
> + break;
> + case 8100:
> + vco_div = 0x0;
> + pixel_freq = 8100000000UL / 6;
> + break;
> + default:
> + /* Other link rates aren't supported */
> + return -EINVAL;
> + }
> +
> + writel(vco_div, edp->edp + DP_PHY_VCO_DIV);
> +
> + clk_set_rate(edp->dp_link_hw.clk, dp_opts->link_rate * 100000);
> + clk_set_rate(edp->dp_pixel_hw.clk, pixel_freq);
> +
> + return 0;
> +}
> +
> +static int qcom_edp_phy_power_on(struct phy *phy)
> +{
> + struct qcom_edp *edp = phy_get_drvdata(phy);
> + int timeout;
> + int ret;
> + u32 val;
> +
> + writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> + DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
> + DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> + edp->edp + DP_PHY_PD_CTL);
> + writel(0xfc, edp->edp + DP_PHY_MODE);
> +
> + timeout = readl_poll_timeout(edp->pll + QSERDES_COM_CMN_STATUS,
> + val, val & BIT(7), 5, 200);
> + if (timeout)
> + return timeout;
> +
> + writel(0x01, edp->tx0 + TXn_LDO_CONFIG);
> + writel(0x01, edp->tx1 + TXn_LDO_CONFIG);
> + writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
> + writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
> +
> + ret = qcom_edp_configure_ssc(edp);
> + if (ret)
> + return ret;
> +
> + ret = qcom_edp_configure_pll(edp);
> + if (ret)
> + return ret;
> +
> + /* TX Lane configuration */
> + writel(0x05, edp->edp + DP_PHY_TX0_TX1_LANE_CTL);
> + writel(0x05, edp->edp + DP_PHY_TX2_TX3_LANE_CTL);
> +
> + /* TX-0 register configuration */
> + writel(0x03, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> + writel(0x0f, edp->tx0 + TXn_CLKBUF_ENABLE);
> + writel(0x03, edp->tx0 + TXn_RESET_TSYNC_EN);
> + writel(0x01, edp->tx0 + TXn_TRAN_DRVR_EMP_EN);
> + writel(0x04, edp->tx0 + TXn_TX_BAND);
> +
> + /* TX-1 register configuration */
> + writel(0x03, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> + writel(0x0f, edp->tx1 + TXn_CLKBUF_ENABLE);
> + writel(0x03, edp->tx1 + TXn_RESET_TSYNC_EN);
> + writel(0x01, edp->tx1 + TXn_TRAN_DRVR_EMP_EN);
> + writel(0x04, edp->tx1 + TXn_TX_BAND);
> +
> + ret = qcom_edp_set_vco_div(edp);
> + if (ret)
> + return ret;
> +
> + writel(0x01, edp->edp + DP_PHY_CFG);
> + writel(0x05, edp->edp + DP_PHY_CFG);
> + writel(0x01, edp->edp + DP_PHY_CFG);
> + writel(0x09, edp->edp + DP_PHY_CFG);
> +
> + writel(0x20, edp->pll + QSERDES_COM_RESETSM_CNTRL);
> +
> + timeout = readl_poll_timeout(edp->pll + QSERDES_COM_C_READY_STATUS,
> + val, val & BIT(0), 500, 10000);
> + if (timeout)
> + return timeout;
> +
> + writel(0x19, edp->edp + DP_PHY_CFG);
> + writel(0x1f, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> + writel(0x04, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> + writel(0x00, edp->tx0 + TXn_TX_POL_INV);
> + writel(0x1f, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> + writel(0x04, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> + writel(0x00, edp->tx1 + TXn_TX_POL_INV);
> + writel(0x10, edp->tx0 + TXn_TX_DRV_LVL_OFFSET);
> + writel(0x10, edp->tx1 + TXn_TX_DRV_LVL_OFFSET);
> + writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX0);
> + writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX1);
> + writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX0);
> + writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX1);
> +
> + writel(0x10, edp->tx0 + TXn_TX_EMP_POST1_LVL);
> + writel(0x10, edp->tx1 + TXn_TX_EMP_POST1_LVL);
> + writel(0x1f, edp->tx0 + TXn_TX_DRV_LVL);
> + writel(0x1f, edp->tx1 + TXn_TX_DRV_LVL);
> +
> + writel(0x4, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> + writel(0x3, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> + writel(0x4, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> + writel(0x0, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> + writel(0x3, edp->edp + DP_PHY_CFG_1);
> +
> + writel(0x18, edp->edp + DP_PHY_CFG);
> + udelay(100);
> +
> + writel(0x19, edp->edp + DP_PHY_CFG);
> +
> + return readl_poll_timeout(edp->edp + DP_PHY_STATUS,
> + val, val & BIT(1), 500, 10000);
> +}
> +
> +static int qcom_edp_phy_power_off(struct phy *phy)
> +{
> + struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> + writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
> +
> + return 0;
> +}
> +
> +static int qcom_edp_phy_exit(struct phy *phy)
> +{
> + struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> + clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks);
> + regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
> +
> + return 0;
> +}
> +
> +static const struct phy_ops qcom_edp_ops = {
> + .init = qcom_edp_phy_init,
> + .configure = qcom_edp_phy_configure,
> + .power_on = qcom_edp_phy_power_on,
> + .power_off = qcom_edp_phy_power_off,
> + .exit = qcom_edp_phy_exit,
> + .owner = THIS_MODULE,
> +};
> +
> +/*
> + * Display Port PLL driver block diagram for branch clocks
Embedded DisplayPort
> + *
> + * +------------------------------+
> + * | DP_VCO_CLK |
> + * | |
> + * | +-------------------+ |
> + * | | (DP PLL/VCO) | |
> + * | +---------+---------+ |
> + * | v |
> + * | +----------+-----------+ |
> + * | | hsclk_divsel_clk_src | |
> + * | +----------+-----------+ |
> + * +------------------------------+
> + * |
> + * +---------<---------v------------>----------+
> + * | |
> + * +--------v----------------+ |
> + * | dp_phy_pll_link_clk | |
> + * | link_clk | |
> + * +--------+----------------+ |
> + * | |
> + * | |
> + * v v
> + * Input to DISPCC block |
> + * for link clk, crypto clk |
> + * and interface clock |
> + * |
> + * |
> + * +--------<------------+-----------------+---<---+
> + * | | |
> + * +----v---------+ +--------v-----+ +--------v------+
> + * | vco_divided | | vco_divided | | vco_divided |
> + * | _clk_src | | _clk_src | | _clk_src |
> + * | | | | | |
> + * |divsel_six | | divsel_two | | divsel_four |
> + * +-------+------+ +-----+--------+ +--------+------+
> + * | | |
> + * v---->----------v-------------<------v
> + * |
> + * +----------+-----------------+
> + * | dp_phy_pll_vco_div_clk |
> + * +---------+------------------+
> + * |
> + * v
> + * Input to DISPCC block
> + * for DP pixel clock
> + *
> + */
> +static int qcom_edp_dp_pixel_clk_determine_rate(struct clk_hw *hw,
> + struct clk_rate_request *req)
> +{
> + switch (req->rate) {
> + case 1620000000UL / 2:
> + case 2700000000UL / 2:
> + /* 5.4 and 8.1 GHz are same link rate as 2.7GHz, i.e. div 4 and div 6 */
> + return 0;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static unsigned long
> +qcom_edp_dp_pixel_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> +{
> + const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_pixel_hw);
> + const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +
> + switch (dp_opts->link_rate) {
> + case 1620:
> + return 1620000000UL / 2;
> + case 2700:
> + return 2700000000UL / 2;
> + case 5400:
> + return 5400000000UL / 4;
> + case 8100:
> + return 8100000000UL / 6;
> + default:
> + return 0;
> + }
> +}
> +
> +static const struct clk_ops qcom_edp_dp_pixel_clk_ops = {
> + .determine_rate = qcom_edp_dp_pixel_clk_determine_rate,
> + .recalc_rate = qcom_edp_dp_pixel_clk_recalc_rate,
> +};
> +
> +static int qcom_edp_dp_link_clk_determine_rate(struct clk_hw *hw,
> + struct clk_rate_request *req)
> +{
> + switch (req->rate) {
> + case 162000000:
> + case 270000000:
> + case 540000000:
> + case 810000000:
> + return 0;
Should we check here that the rate passed actually matches the link
rate set via dp_opts?
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static unsigned long
> +qcom_edp_dp_link_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> +{
> + const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_link_hw);
> + const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +
> + switch (dp_opts->link_rate) {
> + case 1620:
> + case 2700:
> + case 5400:
> + case 8100:
> + return dp_opts->link_rate * 100000;
> + default:
> + return 0;
> + }
> +}
> +
> +static const struct clk_ops qcom_edp_dp_link_clk_ops = {
> + .determine_rate = qcom_edp_dp_link_clk_determine_rate,
> + .recalc_rate = qcom_edp_dp_link_clk_recalc_rate,
> +};
> +
> +static struct clk_hw *
> +qcom_edp_dp_clks_hw_get(struct of_phandle_args *clkspec, void *data)
> +{
> + unsigned int idx = clkspec->args[0];
> + struct qcom_edp *edp = data;
> +
> + if (idx >= 2) {
> + pr_err("%s: invalid index %u\n", __func__, idx);
> + return ERR_PTR(-EINVAL);
> + }
> +
> + if (idx == 0)
> + return &edp->dp_link_hw;
> +
> + return &edp->dp_pixel_hw;
> +}
You might want to use of_clk_hw_onecell_get() instead of the special function.
> +
> +static int qcom_edp_clks_register(struct qcom_edp *edp, struct device_node *np)
> +{
> + struct clk_init_data init = { };
> + int ret;
> +
> + init.ops = &qcom_edp_dp_link_clk_ops;
> + init.name = "edp_phy_pll_link_clk";
> + edp->dp_link_hw.init = &init;
> + ret = devm_clk_hw_register(edp->dev, &edp->dp_link_hw);
> + if (ret)
> + return ret;
> +
> + init.ops = &qcom_edp_dp_pixel_clk_ops;
> + init.name = "edp_phy_pll_vco_div_clk";
> + edp->dp_pixel_hw.init = &init;
> + ret = devm_clk_hw_register(edp->dev, &edp->dp_pixel_hw);
> + if (ret)
> + return ret;
> +
> + return devm_of_clk_add_hw_provider(edp->dev, qcom_edp_dp_clks_hw_get, edp);
> +}
> +
> +static int qcom_edp_phy_probe(struct platform_device *pdev)
> +{
> + struct phy_provider *phy_provider;
> + struct device *dev = &pdev->dev;
> + struct qcom_edp *edp;
> + int ret;
> +
> + edp = devm_kzalloc(dev, sizeof(*edp), GFP_KERNEL);
> + if (!edp)
> + return -ENOMEM;
> +
> + edp->dev = dev;
> +
> + edp->edp = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(edp->edp))
> + return PTR_ERR(edp->edp);
> +
> + edp->tx0 = devm_platform_ioremap_resource(pdev, 1);
> + if (IS_ERR(edp->tx0))
> + return PTR_ERR(edp->tx0);
> +
> + edp->tx1 = devm_platform_ioremap_resource(pdev, 2);
> + if (IS_ERR(edp->tx1))
> + return PTR_ERR(edp->tx1);
> +
> + edp->pll = devm_platform_ioremap_resource(pdev, 3);
> + if (IS_ERR(edp->pll))
> + return PTR_ERR(edp->pll);
> +
> + edp->clks[0].id = "aux";
> + edp->clks[1].id = "cfg_ahb";
> + ret = devm_clk_bulk_get(dev, ARRAY_SIZE(edp->clks), edp->clks);
> + if (ret)
> + return ret;
> +
> + edp->supplies[0].supply = "vdda-phy";
> + edp->supplies[1].supply = "vdda-pll";
> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies);
> + if (ret)
> + return ret;
> +
> + ret = qcom_edp_clks_register(edp, pdev->dev.of_node);
> + if (ret)
> + return ret;
> +
> + edp->phy = devm_phy_create(dev, pdev->dev.of_node, &qcom_edp_ops);
> + if (IS_ERR(edp->phy)) {
> + dev_err(dev, "failed to register phy\n");
> + return PTR_ERR(edp->phy);
> + }
> +
> + phy_set_drvdata(edp->phy, edp);
> +
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id qcom_edp_phy_match_table[] = {
> + { .compatible = "qcom,sc8180x-edp-phy" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, qcom_edp_phy_match_table);
> +
> +static struct platform_driver qcom_edp_phy_driver = {
> + .probe = qcom_edp_phy_probe,
> + .driver = {
> + .name = "qcom-edp-phy",
> + .of_match_table = qcom_edp_phy_match_table,
> + },
> +};
> +
> +module_platform_driver(qcom_edp_phy_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm eDP PHY driver");
Should we mention that it's a eDP QMP PHY driver in contrast to the
old eDP from 8x74/8x84?
Also MODULE_AUTHOR seems to be missing.
> +MODULE_LICENSE("GPL v2");
> --
> 2.29.2
>
--
With best wishes
Dmitry
Powered by blists - more mailing lists