| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20211103184939.45263-6-jim2101024@gmail.com>
Date: Wed, 3 Nov 2021 14:49:35 -0400
From: Jim Quinlan <jim2101024@...il.com>
To: linux-pci@...r.kernel.org,
Nicolas Saenz Julienne <nsaenz@...nel.org>,
Rob Herring <robh@...nel.org>, Mark Brown <broonie@...nel.org>,
bcm-kernel-feedback-list@...adcom.com, jim2101024@...il.com,
james.quinlan@...adcom.com
Cc: Florian Fainelli <f.fainelli@...il.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
Krzysztof Wilczyński <kw@...ux.com>,
Bjorn Helgaas <bhelgaas@...gle.com>,
linux-rpi-kernel@...ts.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-arm-kernel@...ts.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-kernel@...r.kernel.org (open list)
Subject: [PATCH v7 5/7] PCI: brcmstb: Add control of subdevice voltage regulators
This Broadcom STB PCIe RC driver has one port and connects directly to one
device, be it a switch or an endpoint. We want to be able to turn on/off
any regulators for that device. Control of regulators is needed because of
the chicken-and-egg situation: although the regulator is "owned" by the
device and would be best handled by its driver, the device cannot be
discovered and probed unless its regulator is already turned on.
Signed-off-by: Jim Quinlan <jim2101024@...il.com>
---
drivers/pci/controller/pcie-brcmstb.c | 156 +++++++++++++++++++++++++-
1 file changed, 154 insertions(+), 2 deletions(-)
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index ba4d6daf312c..aaf6a4cbeb78 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -24,6 +24,7 @@
#include <linux/pci.h>
#include <linux/pci-ecam.h>
#include <linux/printk.h>
+#include <linux/regulator/consumer.h>
#include <linux/reset.h>
#include <linux/sizes.h>
#include <linux/slab.h>
@@ -191,6 +192,15 @@ static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie,
static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val);
static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
+static int brcm_pcie_add_bus(struct pci_bus *bus);
+static void brcm_pcie_remove_bus(struct pci_bus *bus);
+static bool brcm_pcie_link_up(struct brcm_pcie *pcie);
+
+static const char * const supplies[] = {
+ "vpcie3v3",
+ "vpcie3v3aux",
+ "vpcie12v",
+};
enum {
RGR1_SW_INIT_1,
@@ -295,8 +305,38 @@ struct brcm_pcie {
u32 hw_rev;
void (*perst_set)(struct brcm_pcie *pcie, u32 val);
void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
+ struct regulator_bulk_data supplies[ARRAY_SIZE(supplies)];
+ unsigned int num_supplies;
};
+static int brcm_regulators_on(struct brcm_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ int ret;
+
+ if (!pcie->num_supplies)
+ return 0;
+ ret = regulator_bulk_enable(pcie->num_supplies, pcie->supplies);
+ if (ret)
+ dev_err(dev, "failed to enable EP regulators\n");
+
+ return ret;
+}
+
+static int brcm_regulators_off(struct brcm_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ int ret;
+
+ if (!pcie->num_supplies)
+ return 0;
+ ret = regulator_bulk_disable(pcie->num_supplies, pcie->supplies);
+ if (ret)
+ dev_err(dev, "failed to disable EP regulators\n");
+
+ return ret;
+}
+
/*
* This is to convert the size of the inbound "BAR" region to the
* non-linear values of PCIE_X_MISC_RC_BAR[123]_CONFIG_LO.SIZE
@@ -722,6 +762,8 @@ static struct pci_ops brcm_pcie_ops = {
.map_bus = brcm_pcie_map_conf,
.read = pci_generic_config_read,
.write = pci_generic_config_write,
+ .add_bus = brcm_pcie_add_bus,
+ .remove_bus = brcm_pcie_remove_bus,
};
static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val)
@@ -1148,6 +1190,47 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
pcie->bridge_sw_init_set(pcie, 1);
}
+static int brcm_pcie_get_regulators(struct brcm_pcie *pcie, struct device *dev)
+{
+ const unsigned int ns = ARRAY_SIZE(supplies);
+ struct device_node *dn;
+ struct property *pp;
+ unsigned int i;
+ int ret;
+
+ /* This is for Broadcom STB/CM chips only */
+ if (pcie->type == BCM2711)
+ return 0;
+
+ dn = dev->of_node;
+ if (!dn)
+ return 0;
+
+ for_each_property_of_node(dn, pp) {
+ for (i = 0; i < ns; i++) {
+ char prop_name[64]; /* 64 is max size of property name */
+
+ snprintf(prop_name, 64, "%s-supply", supplies[i]);
+ if (strcmp(prop_name, pp->name) == 0)
+ break;
+ }
+ if (i >= ns || pcie->num_supplies >= ARRAY_SIZE(supplies))
+ continue;
+
+ pcie->supplies[pcie->num_supplies++].supply = supplies[i];
+ }
+
+ if (pcie->num_supplies == 0)
+ return 0;
+
+ ret = devm_regulator_bulk_get(dev, pcie->num_supplies,
+ pcie->supplies);
+ if (ret)
+ dev_err(dev, "failed to get EP regulators\n");
+
+ return ret;
+}
+
static int brcm_pcie_suspend(struct device *dev)
{
struct brcm_pcie *pcie = dev_get_drvdata(dev);
@@ -1158,7 +1241,7 @@ static int brcm_pcie_suspend(struct device *dev)
reset_control_rearm(pcie->rescal);
clk_disable_unprepare(pcie->clk);
- return ret;
+ return brcm_regulators_off(pcie);
}
static int brcm_pcie_resume(struct device *dev)
@@ -1174,6 +1257,9 @@ static int brcm_pcie_resume(struct device *dev)
ret = reset_control_reset(pcie->rescal);
if (ret)
goto err_disable_clk;
+ ret = brcm_regulators_on(pcie);
+ if (ret)
+ goto err_reset;
ret = brcm_phy_start(pcie);
if (ret)
@@ -1241,6 +1327,62 @@ static const struct of_device_id brcm_pcie_match[] = {
{},
};
+static int brcm_pcie_add_bus(struct pci_bus *bus)
+{
+ struct pci_host_bridge *hb = pci_find_host_bridge(bus);
+ struct brcm_pcie *pcie = (struct brcm_pcie *) hb->sysdata;
+ struct device *dev = &bus->dev;
+ int ret;
+
+ /*
+ * We only care about a device that is directly connected
+ * to the root complex, ie bus == 1 and slot == 0.
+ */
+ if (bus->number != 1)
+ return 0;
+
+ ret = brcm_pcie_get_regulators(pcie, dev);
+ if (ret)
+ goto err_out;
+
+ ret = brcm_regulators_on(pcie);
+ if (ret)
+ goto err_out;
+
+ ret = brcm_pcie_linkup(pcie);
+ if (ret)
+ goto err_out;
+
+ return 0;
+
+err_out:
+ /*
+ * If we have failed there is no point to return the exact reason,
+ * as currently it will cause a WARNING() from
+ * pci_alloc_child_bus(). We return -ENOLINK to the caller, which
+ * unlike any other errors, will stop the PCIe tree exploration.
+ */
+ return -ENOLINK;
+}
+
+static void brcm_pcie_remove_bus(struct pci_bus *bus)
+{
+ struct pci_host_bridge *hb = pci_find_host_bridge(bus);
+ struct brcm_pcie *pcie = (struct brcm_pcie *) hb->sysdata;
+ struct device *dev = &bus->dev;
+ int ret;
+
+ if (bus->number != 1)
+ return;
+
+ if (pcie->num_supplies > 0) {
+ ret = brcm_regulators_off(pcie, true);
+ if (ret)
+ dev_err(dev, "Could not turn of regulators\n");
+ pcie->num_supplies = 0;
+ }
+}
+
static int brcm_pcie_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node, *msi_np;
@@ -1332,7 +1474,17 @@ static int brcm_pcie_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, pcie);
- return pci_host_probe(bridge);
+ ret = pci_host_probe(bridge);
+ if (!ret && !brcm_pcie_link_up(pcie))
+ ret = -ENODEV;
+
+ if (ret) {
+ brcm_pcie_remove(pdev);
+ return ret;
+ }
+
+ return 0;
+
fail:
__brcm_pcie_remove(pcie);
return ret;
--
2.17.1
Powered by blists - more mailing lists