Message-ID: <20211105094310.GI6526@e120937-lin>
Date:   Fri, 5 Nov 2021 09:43:10 +0000
From:   Cristian Marussi <cristian.marussi@....com>
To:     rishabhb@...eaurora.org
Cc:     Sudeep Holla <sudeep.holla@....com>,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        avajid@...eaurora.org, adharmap@...eaurora.org
Subject: Re: [PATCH v3] firmware: arm_scmi: Free mailbox channels if probe
 fails

On Thu, Nov 04, 2021 at 04:40:03PM -0700, rishabhb@...eaurora.org wrote:
> On 2021-11-02 04:32, Sudeep Holla wrote:
> > On Mon, Nov 01, 2021 at 09:35:42AM -0700, rishabhb@...eaurora.org wrote:
> > > On 2021-09-01 02:35, Cristian Marussi wrote:
> > > > On Tue, Aug 31, 2021 at 06:48:35AM +0100, Cristian Marussi wrote:
> > > > > On Mon, Aug 30, 2021 at 02:09:37PM -0700, rishabhb@...eaurora.org
> > > > > wrote:
> > > > > > Hi Christian
> > > > >
> > > > > Hi Rishabh,
> > > > >

Hi Rishabh,

apologies for the delay in coming back to you.
A few comments below.

> > > > > thanks for looking into this kind of bad interactions.
> > > > >
> > > > > > There seems to be another issue here. The response from agent can be delayed
> > > > > > causing a timeout during base protocol acquire,
> > > > > > which leads to the probe failure. What I have observed is sometimes the
> > > > > > failure of probe and rx_callback (due to a delayed message)
> > > > > > happens at the same time on different cpus.
> > > > > > Because of this race, the device memory may be cleared while the
> > > > > > interrupt(rx_callback) is executing on another cpu.
> > > > >
> > > > > You are right that concurrency was not handled properly in this kind
> > > > > of
> > > > > context and moreover, if you think about it, even the case of out of
> > > > > order reception of responses and delayed_responses (type2 SCMI
> > > > > messages)
> > > > > for asynchronous SCMI commands was not handled properly.
> > > > >
> > > > > > How do you propose we solve this? Do you think it is better to take the
> > > > > > setting up of base and other protocols out of probe and
> > > > > > in some delayed work? That would imply the device memory is not released
> > > > > > until remove is called. Or should we add locking to
> > > > > > the interrupt handler(scmi_rx_callback) and the cleanup in probe to avoid
> > > > > > the race?
> > > > > >
> > > > >
> > > > > These issues were more easily exposed by SCMI Virtio transport, so in
> > > > > the series where I introduced scmi-virtio:
> > > > >
> > > > > https://lore.kernel.org/linux-arm-kernel/162848483974.232214.9506203742448269364.b4-ty@arm.com/
> > > > >
> > > > > (which is now queued for v5.15 ...  now on -next I think...finger
> > > > > crossed)
> > > > >
> > > > > I took the chance to rectify a couple of other things in the SCMI core
> > > > > in the initial commits.
> > > > > As an example, in the above series
> > > > >
> > > > >  [PATCH v7 05/15] firmware: arm_scmi: Handle concurrent and
> > > > > out-of-order messages
> > > > >
> > > > > cares to add a refcount to xfers and some locking on xfers between TX
> > > > > and RX path to avoid that a timed out xfer can vanish while the rx
> > > > > path
> > > > > is concurrently working on it (as you said); moreover I handle the
> > > > > condition (rare if not unplausible anyway) in which a transport
> > > > > delivers
> > > > > out of order responses and delayed responses.
> > > > >
> > > > > I tested this scenarios on some fake emulated SCMI Virtio transport
> > > > > where I could play any sort of mess and tricks to stress this limit
> > > > > conditions, but you're more than welcome to verify if the race you are
> > > > > seeing on Base protocol time out is solved (as I would hope :D) by
> > > > > this
> > > > > series of mine.
> > > > >
> > > > > Let me know, any feedback is welcome.
> > > > >
> > > > > Btw, in the series above there are also other minor changes, but there
> > > > > is also another more radical change needed to ensure correctness and
> > > > > protection against stale old messages which maybe could interest you
> > > > > in general if you are looking into SCMI:
> > > > >
> > > > > [PATCH v7 04/15] firmware: arm_scmi: Introduce monotonically
> > > > > increasing tokens
> > > > >
> > > > > Let me know if yo have other concerns.
> > > > >
> > > >
> > > > Hi Rishabhb,
> > > >
> > > > just a quick remark, thinking again about your fail @probe scenario
> > > > above
> > > > I realized that while the concurrency patch I mentioned above could help
> > > > on
> > > > races against vanishing xfers when late timed-out responses are
> > > > delivered,
> > > > here we really are then also shutting down everything on failure, so
> > > > there
> > > > could be further issues between a very late invokation of
> > > > scmi_rx_callback
> > > > and the core devm_ helpers freeing the underlying xfer/cinfo/etc..
> > > > structs
> > > > used by scmi-rx-callback itself (maybe this was already what you meant
> > > > and
> > > > I didn't get it,...sorry)
> > > >
> > > > On the other side, I don't feel that delaying Base init to a deferred
> > > > worker is a viable solution since we need Base protocol init to be
> > > > initialized and we need to just give up if we cannot communicate with
> > > > the SCMI platform fw in such early stages. (Base protocol is really the
> > > > only mandatory proto is I remember correctly the spec)
> > > >
> > > > Currenly I'm off and only glancing at mails but I'll have a thought
> > > > about
> > > > these issues once back in a few weeks time.
> > > >
> > > > Thanks,
> > > > Cristian
> > > >
> > > Hi Cristian
> > > I hope you enjoyed your vacation. Did you get a chance to look at
> > > the issue
> > > stated above and have some idea as to how to solve this?
> > 
> > Do you still see the issue with v5.15 ? Can you please check if haven't
> > already done that ?
> > 
> > Also 30ms delay we have is huge IMO and we typically expect the
> > communication
> > with remote processor or any entity that implements SCMI to happen in
> > terms
> > of one or few ms tops.
> > 
> > If there is a race, we need to fix that but I am interested in knowing
> > why the default time of 30ms not sufficient ? Did increasing that helps
> > and is this timeout happening only for the initial commands(guessing the
> > SCMI firmware is not yet ready) or does it happen even during run-time ?
> 
> Hi Sudeep
> I haven't checked on 5.15 but after glancing at the code I believe we should
> see the same issue.
> I agree 30ms is a big enough value and should be something that remote
> firmware should resolve. But
> if remote firmware goes into a bad state and not functioning properly at
> least kernel should not panic.
> 
> The issue we see here happens during scmi probe. The response from the
> remote agent can be delayed
> causing a timeout during base protocol acquire, which leads to the probe
> failure.
> What I have observed is sometimes the failure of probe and rx_callback (due
> to a delayed message)
> happens around the same time on different cpus. Because of this race, the
> device memory may be cleared
> while the interrupt(rx_callback) is executing on another cpu.

So I was looking at the failure path you mentioned: a late concurrent
reply on Base protocol from the fw, during the probe, leads to an invocation
of scmi_rx_callback() on a different CPU while core data structs like
cinfo are being freed by the SCMI core on the probe failure path.
(v5.15-added SCMI concurrrency handling stuff I mentiond shuld help for
races regarding xfer but not for the cinfo stuff in this case ...)

We cannot defer Base proto init since we just wanna fail early while
probing if not even the Base protocol can work fine, and also because
Base protocol information are indeed needed for initial setup, so we
cannot juts proceed if we did not even got a Base reply on the number of
protos. (already said)

In my opinion, the proper way to address this kind of races at probe
failure should be to ensure that the transport you are using is properly
shut down completely before cleanup starts (same applies for a clean
remove), i.e. scmi_rx_callback should not even be possibly registered to
be called when the the final cleanup by the core is started (devm_ frees
I mean after scmi_probe exit failing...)

BUT indeed looking back at transport layers like mailbox and virtio, this
should be happening already, because the flow is like

scmi_probe()
{
...

clean_tx_rx_setup:
	scmi_cleanup_txrx_channels()
		....
		--->>>  ret = idr_for_each(idr, info->desc->ops->chan_free, idr);
			-			
	return ret;
}

.... only after this scmi_probe returns the core devm layer starts freeing devm_
allocated stuff like cinfo, AND the above per-transport specific .chan_free seems
to take care to 'deactivate/dregister' the scmi_rx_callback at the
transport layer:


e.g. MBOX transport
-------------------------
static int mailbox_chan_free(int id, void *p, void *data)
{
	struct scmi_chan_info *cinfo = p;
	struct scmi_mailbox *smbox = cinfo->transport_info;

	if (smbox && !IS_ERR(smbox->chan)) {
		mbox_free_channel(smbox->chan);    <<< THIS MBOX CORE CALL DEACTIVATE
		cinfo->transport_info = NULL;


e.g. VIRTIO Transport
-----------------------------
static int virtio_chan_free(int id, void *p, void *data)
{
	unsigned long flags;
	struct scmi_chan_info *cinfo = p;
	struct scmi_vio_channel *vioch = cinfo->transport_info;

	spin_lock_irqsave(&vioch->ready_lock, flags);
	vioch->ready = false;                     <<<< THIS VIRTIO FLAG DEACTIVATE VIRTIO CBS INVOKCATION
	spin_unlock_irqrestore(&vioch->ready_lock, flags);


... AND both of the above call are indeed also spinlocked heavily, so that
the 'deactivation' of the scmi_rx_callback should be visible properly; in
other words I would expect that after the above .chan_free() have
completed the scmi_rx_callback() cannot be called anymore, because the
transport itself will properly drop any so-late fw reply.

So I am now wondering, which transport are you using in your tests ?
since at least for the above 2 example it seems to me that your
race-on-probe failure condition should be already addressed by the
transport layer itself....or am I getting wrong the nature of the race ?

Thanks
Cristian

Powered by blists - more mailing lists