| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20211112183311.9556-1-tharvey@gateworks.com>
Date: Fri, 12 Nov 2021 10:33:11 -0800
From: Tim Harvey <tharvey@...eworks.com>
To: devicetree@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
NXP Linux Team <linux-imx@....com>,
Laurent Pinchart <laurent.pinchart@...asonboard.com>
Cc: linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
Adam Ford <aford173@...il.com>,
Tim Harvey <tharvey@...eworks.com>
Subject: [RFC] arm64: dts: imx8mm: add imx8mm-venice-gw73xx-0x-imx219 overlay
Add support for the RaspberryPi Camera v2 module attached to an
imx8mm-venice-gw73xx-0x.
This camera is an IMX219 8MP module:
- https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
- has its own on-board 24MHz osc so no clock required from baseboard
- pin 11 enables 1.8V and 2.8V LDO which is connected to
GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1). The imx219 driver does not
support powerdown-gpios therefore we use gpio1 via reset-gpios
Support is added via a device-tree overlay.
The IMX219 supports RAW8/RAW10 image formats.
Example usage:
media-ctl --links "'imx219 2-0010':0->'imx7-mipi-csis.0':0[1]"
media-ctl -v -V "'imx219 2-0010':0 [fmt:SRGGB8/640x480 field:none]"
media-ctl -v -V "'csi':0 [fmt:SRGGB8/640x480 field:none]"
gst-launch-1.0 -v v4l2src num-buffers=1 ! \
video/x-bayer,format=rggb,width=640,height=480,framerate=30/1 ! \
bayer2rgb ! jpegenc ! filesink location=test.jpg
gst-launch-1.0 -v v4l2src num-buffers=300 ! \
video/x-bayer,format=rggb,width=640,height=480,framerate=30/1 ! \
bayer2rgb ! jpegenc ! avimux ! filesink location=test.avi
This patch depends on 'arm64: dts: imx8mm: Add CSI nodes' at:
https://lore.kernel.org/all/20211106155427.753197-2-aford173@gmail.com/
This is an RFC as I am not aware of other dt fragments/overlays being
added to the kernel yet. I do get a few warnings but I believe they are
because this is a fragment:
$ make DTC_FLAGS="-@" dtbs W=1
DTC
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts:33.3-16:
Warning (reg_format): /fragment@..._overlay__/sensor@10:reg: property
has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts:52.10-57.5:
Warning (unit_address_vs_reg): /fragment@..._overlay__/ports/port@0:
node has a unit name, but no reg or ranges property
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (pci_device_reg): Failed prerequisite 'reg_format'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (simple_bus_reg): Failed prerequisite 'reg_format'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (spi_bus_reg): Failed prerequisite 'reg_format'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts:29.20-46.4:
Warning (avoid_default_addr_size): /fragment@..._overlay__/sensor@10:
Relying on default #address-cells value
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts:29.20-46.4:
Warning (avoid_default_addr_size): /fragment@..._overlay__/sensor@10:
Relying on default #size-cells value
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (avoid_unnecessary_addr_size): Failed prerequisite
'avoid_default_addr_size'
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dtb:
Warning (unique_unit_address): Failed prerequisite
'avoid_default_addr_size'
The intended use of a dt fragement like this is to apply it in boot
firmware before booting the kernel such as:
u-boot=> load mmc 0:1 $fdt_addr_r imx8mm-venice-gw73xx-0x.dtb
u-boot=> fdt addr $fdt_addr_r
u-boot=> fdt resize
u-boot=> load mmc 0:1 $loadaddr imx8mm-venice-gw73xx-0x-imx219.dtb
u-boot=> fdt appply $loadaddr
u-boot=> load mmc 0:1 $kernel_addr_r Image
u-boot=> booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@...eworks.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../imx8mm-venice-gw73xx-0x-imx219.dts | 67 +++++++++++++++++++
2 files changed, 68 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..cc00ac78dbc6 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-imx219.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts
new file mode 100644
index 000000000000..6f692ba24a31
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+ compatible = "gw,imx8mm-gw73xx-0x", "fsl,imx8mm";
+
+ cam24m: cam24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "cam24m";
+ };
+};
+
+&csi {
+ status = "okay";
+};
+
+&i2c3 {
+ imx219: sensor@10 {
+ compatible = "sony,imx219";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_imx219>;
+ reg = <0x10>;
+ clocks = <&cam24m>;
+ reset-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+
+ port {
+ /* MIPI CSI-2 bus endpoint */
+ imx219_to_mipi_csi2: endpoint {
+ remote-endpoint = <&imx8mm_mipi_csi_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ link-frequencies = /bits/ 64 <456000000>;
+ };
+ };
+ };
+};
+
+&mipi_csi {
+ status = "okay";
+ ports {
+ port@0 {
+ imx8mm_mipi_csi_in: endpoint {
+ remote-endpoint = <&imx219_to_mipi_csi2>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_imx219: imx219grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x41
+ >;
+ };
+};
--
2.17.1
Powered by blists - more mailing lists