| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20211115165425.009779163@linuxfoundation.org>
Date: Mon, 15 Nov 2021 17:53:47 +0100
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Duc Nguyen <duc.nguyen.ub@...esas.com>,
Wolfram Sang <wsa+renesas@...g-engineering.com>,
Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
Subject: [PATCH 5.14 144/849] memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
From: Wolfram Sang <wsa+renesas@...g-engineering.com>
commit fff53a551db50f5edecaa0b29a64056ab8d2bbca upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Cc: <stable@...r.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@...esas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@...g-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/memory/renesas-rpc-if.c | 113 +++++++++++++++++++++++++++-------------
include/memory/renesas-rpc-if.h | 1
2 files changed, 79 insertions(+), 35 deletions(-)
--- a/drivers/memory/renesas-rpc-if.c
+++ b/drivers/memory/renesas-rpc-if.c
@@ -160,10 +160,62 @@ static const struct regmap_access_table
.n_yes_ranges = ARRAY_SIZE(rpcif_volatile_ranges),
};
+
+/*
+ * Custom accessor functions to ensure SMRDR0 and SMWDR0 are always accessed
+ * with proper width. Requires SMENR_SPIDE to be correctly set before!
+ */
+static int rpcif_reg_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct rpcif *rpc = context;
+
+ if (reg == RPCIF_SMRDR0 || reg == RPCIF_SMWDR0) {
+ u32 spide = readl(rpc->base + RPCIF_SMENR) & RPCIF_SMENR_SPIDE(0xF);
+
+ if (spide == 0x8) {
+ *val = readb(rpc->base + reg);
+ return 0;
+ } else if (spide == 0xC) {
+ *val = readw(rpc->base + reg);
+ return 0;
+ } else if (spide != 0xF) {
+ return -EILSEQ;
+ }
+ }
+
+ *val = readl(rpc->base + reg);
+ return 0;
+
+}
+
+static int rpcif_reg_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct rpcif *rpc = context;
+
+ if (reg == RPCIF_SMRDR0 || reg == RPCIF_SMWDR0) {
+ u32 spide = readl(rpc->base + RPCIF_SMENR) & RPCIF_SMENR_SPIDE(0xF);
+
+ if (spide == 0x8) {
+ writeb(val, rpc->base + reg);
+ return 0;
+ } else if (spide == 0xC) {
+ writew(val, rpc->base + reg);
+ return 0;
+ } else if (spide != 0xF) {
+ return -EILSEQ;
+ }
+ }
+
+ writel(val, rpc->base + reg);
+ return 0;
+}
+
static const struct regmap_config rpcif_regmap_config = {
.reg_bits = 32,
.val_bits = 32,
.reg_stride = 4,
+ .reg_read = rpcif_reg_read,
+ .reg_write = rpcif_reg_write,
.fast_io = true,
.max_register = RPCIF_PHYINT,
.volatile_table = &rpcif_volatile_table,
@@ -173,17 +225,15 @@ int rpcif_sw_init(struct rpcif *rpc, str
{
struct platform_device *pdev = to_platform_device(dev);
struct resource *res;
- void __iomem *base;
rpc->dev = dev;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
- base = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(base))
- return PTR_ERR(base);
+ rpc->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(rpc->base))
+ return PTR_ERR(rpc->base);
- rpc->regmap = devm_regmap_init_mmio(&pdev->dev, base,
- &rpcif_regmap_config);
+ rpc->regmap = devm_regmap_init(&pdev->dev, NULL, rpc, &rpcif_regmap_config);
if (IS_ERR(rpc->regmap)) {
dev_err(&pdev->dev,
"failed to init regmap for rpcif, error %ld\n",
@@ -354,20 +404,16 @@ void rpcif_prepare(struct rpcif *rpc, co
nbytes = op->data.nbytes;
rpc->xferlen = nbytes;
- rpc->enable |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes)) |
- RPCIF_SMENR_SPIDB(rpcif_bit_size(op->data.buswidth));
+ rpc->enable |= RPCIF_SMENR_SPIDB(rpcif_bit_size(op->data.buswidth));
}
}
EXPORT_SYMBOL(rpcif_prepare);
int rpcif_manual_xfer(struct rpcif *rpc)
{
- u32 smenr, smcr, pos = 0, max = 4;
+ u32 smenr, smcr, pos = 0, max = rpc->bus_size == 2 ? 8 : 4;
int ret = 0;
- if (rpc->bus_size == 2)
- max = 8;
-
pm_runtime_get_sync(rpc->dev);
regmap_update_bits(rpc->regmap, RPCIF_PHYCNT,
@@ -378,37 +424,36 @@ int rpcif_manual_xfer(struct rpcif *rpc)
regmap_write(rpc->regmap, RPCIF_SMOPR, rpc->option);
regmap_write(rpc->regmap, RPCIF_SMDMCR, rpc->dummy);
regmap_write(rpc->regmap, RPCIF_SMDRENR, rpc->ddr);
+ regmap_write(rpc->regmap, RPCIF_SMADR, rpc->smadr);
smenr = rpc->enable;
switch (rpc->dir) {
case RPCIF_DATA_OUT:
while (pos < rpc->xferlen) {
- u32 nbytes = rpc->xferlen - pos;
- u32 data[2];
+ u32 bytes_left = rpc->xferlen - pos;
+ u32 nbytes, data[2];
smcr = rpc->smcr | RPCIF_SMCR_SPIE;
- if (nbytes > max) {
- nbytes = max;
+
+ /* nbytes may only be 1, 2, 4, or 8 */
+ nbytes = bytes_left >= max ? max : (1 << ilog2(bytes_left));
+ if (bytes_left > nbytes)
smcr |= RPCIF_SMCR_SSLKP;
- }
+
+ smenr |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes));
+ regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
memcpy(data, rpc->buffer + pos, nbytes);
- if (nbytes > 4) {
+ if (nbytes == 8) {
regmap_write(rpc->regmap, RPCIF_SMWDR1,
data[0]);
regmap_write(rpc->regmap, RPCIF_SMWDR0,
data[1]);
- } else if (nbytes > 2) {
+ } else {
regmap_write(rpc->regmap, RPCIF_SMWDR0,
data[0]);
- } else {
- regmap_write(rpc->regmap, RPCIF_SMWDR0,
- data[0] << 16);
}
- regmap_write(rpc->regmap, RPCIF_SMADR,
- rpc->smadr + pos);
- regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
regmap_write(rpc->regmap, RPCIF_SMCR, smcr);
ret = wait_msg_xfer_end(rpc);
if (ret)
@@ -448,14 +493,16 @@ int rpcif_manual_xfer(struct rpcif *rpc)
break;
}
while (pos < rpc->xferlen) {
- u32 nbytes = rpc->xferlen - pos;
- u32 data[2];
+ u32 bytes_left = rpc->xferlen - pos;
+ u32 nbytes, data[2];
- if (nbytes > max)
- nbytes = max;
+ /* nbytes may only be 1, 2, 4, or 8 */
+ nbytes = bytes_left >= max ? max : (1 << ilog2(bytes_left));
regmap_write(rpc->regmap, RPCIF_SMADR,
rpc->smadr + pos);
+ smenr &= ~RPCIF_SMENR_SPIDE(0xF);
+ smenr |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes));
regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
regmap_write(rpc->regmap, RPCIF_SMCR,
rpc->smcr | RPCIF_SMCR_SPIE);
@@ -463,18 +510,14 @@ int rpcif_manual_xfer(struct rpcif *rpc)
if (ret)
goto err_out;
- if (nbytes > 4) {
+ if (nbytes == 8) {
regmap_read(rpc->regmap, RPCIF_SMRDR1,
&data[0]);
regmap_read(rpc->regmap, RPCIF_SMRDR0,
&data[1]);
- } else if (nbytes > 2) {
- regmap_read(rpc->regmap, RPCIF_SMRDR0,
- &data[0]);
- } else {
+ } else {
regmap_read(rpc->regmap, RPCIF_SMRDR0,
&data[0]);
- data[0] >>= 16;
}
memcpy(rpc->buffer + pos, data, nbytes);
--- a/include/memory/renesas-rpc-if.h
+++ b/include/memory/renesas-rpc-if.h
@@ -59,6 +59,7 @@ struct rpcif_op {
struct rpcif {
struct device *dev;
+ void __iomem *base;
void __iomem *dirmap;
struct regmap *regmap;
struct reset_control *rstc;
Powered by blists - more mailing lists