Message-ID: <3223d1b6-1922-e5d0-9a6e-24ac25514f2b@roeck-us.net>
Date:   Thu, 18 Nov 2021 10:19:49 -0800
From:   Guenter Roeck <linux@...ck-us.net>
To:     Sander Vanheule <sander@...nheule.net>,
        linux-watchdog@...r.kernel.org, devicetree@...r.kernel.org
Cc:     Wim Van Sebroeck <wim@...ux-watchdog.org>,
        Rob Herring <robh+dt@...nel.org>, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v4 2/2] watchdog: Add Realtek Otto watchdog timer

On 11/18/21 8:29 AM, Sander Vanheule wrote:
> Realtek MIPS SoCs (platform name Otto) have a watchdog timer with
> pretimeout notifitication support. The WDT can (partially) hard reset,
> or soft reset the SoC.
> 
> This driver implements all features as described in the devicetree
> binding, except the phase2 interrupt, and also functions as a restart
> handler. The cpu reset mode is considered to be a "warm" restart, since
> this mode does not reset all peripherals. Being an embedded system
> though, the "cpu" and "software" modes will still cause the bootloader
> to run on restart.
> 
> It is not known how a forced system reset can be disabled on the
> supported platforms. This means that the phase2 interrupt will only fire
> at the same time as reset, so implementing phase2 is of little use.
> 
> Signed-off-by: Sander Vanheule <sander@...nheule.net>

Reviewed-by: Guenter Roeck <linux@...ck-us.net>

> 
> ---
> v3 -> v4:
> - Do a full clock probe with clk_prepare_enable
> - Cache the clock rate instead of keeping a reference to the clk object
> - Only return error value if platform_get_irq_byname fails, that call is
>    already verbose enough
> 
> v2 -> v3:
> - fix off-by-one error in PRESCALE assignment
> 
> v1 -> v2:
> - drop raw_spinlock, locking is not required
> - replace devm_free_irq with disable_irq
> - use max_hw_heartbeat_ms instead of max_timeout
> - drop redundant timeout value checks
> - replace ROUND_CLOSEST by ROUND_UP for tick counts, and flooring
>    division for timeout values
> - change COMMON_CLK 'select' into 'depends on'
> - add MODULE_DEVICE_TABLE for OF ID table
> - add realtek,rtl9300 compatible
> - drop phase2 irq
> ---
>   MAINTAINERS                         |   7 +
>   drivers/watchdog/Kconfig            |  13 +
>   drivers/watchdog/Makefile           |   1 +
>   drivers/watchdog/realtek_otto_wdt.c | 384 ++++++++++++++++++++++++++++
>   4 files changed, 405 insertions(+)
>   create mode 100644 drivers/watchdog/realtek_otto_wdt.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7a2345ce8521..2e255902dd90 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -16122,6 +16122,13 @@ S:	Maintained
>   F:	include/sound/rt*.h
>   F:	sound/soc/codecs/rt*
>   
> +REALTEK OTTO WATCHDOG
> +M:	Sander Vanheule <sander@...nheule.net>
> +L:	linux-watchdog@...r.kernel.org
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/watchdog/realtek,otto-wdt.yaml
> +F:	driver/watchdog/realtek_otto_wdt.c
> +
>   REALTEK RTL83xx SMI DSA ROUTER CHIPS
>   M:	Linus Walleij <linus.walleij@...aro.org>
>   S:	Maintained
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index 9d222ba17ec6..e64de8cf5dbd 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -940,6 +940,19 @@ config RTD119X_WATCHDOG
>   	  Say Y here to include support for the watchdog timer in
>   	  Realtek RTD1295 SoCs.
>   
> +config REALTEK_OTTO_WDT
> +	tristate "Realtek Otto MIPS watchdog support"
> +	depends on MACH_REALTEK_RTL || COMPILE_TEST
> +	depends on COMMON_CLK
> +	select WATCHDOG_CORE
> +	default MACH_REALTEK_RTL
> +	help
> +	  Say Y here to include support for the watchdog timer on Realtek
> +	  RTL838x, RTL839x, RTL930x SoCs. This watchdog has pretimeout
> +	  notifications and system reset on timeout.
> +
> +	  When built as a module this will be called realtek_otto_wdt.
> +
>   config SPRD_WATCHDOG
>   	tristate "Spreadtrum watchdog support"
>   	depends on ARCH_SPRD || COMPILE_TEST
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 2ee97064145b..cca144bc7cd8 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -170,6 +170,7 @@ obj-$(CONFIG_IMGPDC_WDT) += imgpdc_wdt.o
>   obj-$(CONFIG_MT7621_WDT) += mt7621_wdt.o
>   obj-$(CONFIG_PIC32_WDT) += pic32-wdt.o
>   obj-$(CONFIG_PIC32_DMT) += pic32-dmt.o
> +obj-$(CONFIG_REALTEK_OTTO_WDT) += realtek_otto_wdt.o
>   
>   # PARISC Architecture
>   
> diff --git a/drivers/watchdog/realtek_otto_wdt.c b/drivers/watchdog/realtek_otto_wdt.c
> new file mode 100644
> index 000000000000..60058a0c3ec4
> --- /dev/null
> +++ b/drivers/watchdog/realtek_otto_wdt.c
> @@ -0,0 +1,384 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/*
> + * Realtek Otto MIPS platform watchdog
> + *
> + * Watchdog timer that will reset the system after timeout, using the selected
> + * reset mode.
> + *
> + * Counter scaling and timeouts:
> + * - Base prescale of (2 << 25), providing tick duration T_0: 168ms @ 200MHz
> + * - PRESCALE: logarithmic prescaler adding a factor of {1, 2, 4, 8}
> + * - Phase 1: Times out after (PHASE1 + 1) × PRESCALE × T_0
> + *   Generates an interrupt, WDT cannot be stopped after phase 1
> + * - Phase 2: starts after phase 1, times out after (PHASE2 + 1) × PRESCALE × T_0
> + *   Resets the system according to RST_MODE
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/math.h>
> +#include <linux/minmax.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/reboot.h>
> +#include <linux/watchdog.h>
> +
> +#define OTTO_WDT_REG_CNTR		0x0
> +#define OTTO_WDT_CNTR_PING		BIT(31)
> +
> +#define OTTO_WDT_REG_INTR		0x4
> +#define OTTO_WDT_INTR_PHASE_1		BIT(31)
> +#define OTTO_WDT_INTR_PHASE_2		BIT(30)
> +
> +#define OTTO_WDT_REG_CTRL		0x8
> +#define OTTO_WDT_CTRL_ENABLE		BIT(31)
> +#define OTTO_WDT_CTRL_PRESCALE		GENMASK(30, 29)
> +#define OTTO_WDT_CTRL_PHASE1		GENMASK(26, 22)
> +#define OTTO_WDT_CTRL_PHASE2		GENMASK(19, 15)
> +#define OTTO_WDT_CTRL_RST_MODE		GENMASK(1, 0)
> +#define OTTO_WDT_MODE_SOC		0
> +#define OTTO_WDT_MODE_CPU		1
> +#define OTTO_WDT_MODE_SOFTWARE		2
> +#define OTTO_WDT_CTRL_DEFAULT		OTTO_WDT_MODE_CPU
> +
> +#define OTTO_WDT_PRESCALE_MAX		3
> +
> +/*
> + * One higher than the max values contained in PHASE{1,2}, since a value of 0
> + * corresponds to one tick.
> + */
> +#define OTTO_WDT_PHASE_TICKS_MAX	32
> +
> +/*
> + * The maximum reset delay is actually 2×32 ticks, but that would require large
> + * pretimeout values for timeouts longer than 32 ticks. Limit the maximum timeout
> + * to 32 + 1 to ensure small pretimeout values can be configured as expected.
> + */
> +#define OTTO_WDT_TIMEOUT_TICKS_MAX	(OTTO_WDT_PHASE_TICKS_MAX + 1)
> +
> +struct otto_wdt_ctrl {
> +	struct watchdog_device wdev;
> +	struct device *dev;
> +	void __iomem *base;
> +	unsigned int clk_rate_khz;
> +	int irq_phase1;
> +};
> +
> +static int otto_wdt_start(struct watchdog_device *wdev)
> +{
> +	struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
> +	u32 v;
> +
> +	v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
> +	v |= OTTO_WDT_CTRL_ENABLE;
> +	iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_stop(struct watchdog_device *wdev)
> +{
> +	struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
> +	u32 v;
> +
> +	v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
> +	v &= ~OTTO_WDT_CTRL_ENABLE;
> +	iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_ping(struct watchdog_device *wdev)
> +{
> +	struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
> +
> +	iowrite32(OTTO_WDT_CNTR_PING, ctrl->base + OTTO_WDT_REG_CNTR);
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_tick_ms(struct otto_wdt_ctrl *ctrl, int prescale)
> +{
> +	return DIV_ROUND_CLOSEST(1 << (25 + prescale), ctrl->clk_rate_khz);
> +}
> +
> +/*
> + * The timer asserts the PHASE1/PHASE2 IRQs when the number of ticks exceeds
> + * the value stored in those fields. This means each phase will run for at least
> + * one tick, so small values need to be clamped to correctly reflect the timeout.
> + */
> +static inline unsigned int div_round_ticks(unsigned int val, unsigned int tick_duration,
> +		unsigned int min_ticks)
> +{
> +	return max(min_ticks, DIV_ROUND_UP(val, tick_duration));
> +}
> +
> +static int otto_wdt_determine_timeouts(struct watchdog_device *wdev, unsigned int timeout,
> +		unsigned int pretimeout)
> +{
> +	struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
> +	unsigned int pretimeout_ms = pretimeout * 1000;
> +	unsigned int timeout_ms = timeout * 1000;
> +	unsigned int prescale_next = 0;
> +	unsigned int phase1_ticks;
> +	unsigned int phase2_ticks;
> +	unsigned int total_ticks;
> +	unsigned int prescale;
> +	unsigned int tick_ms;
> +	u32 v;
> +
> +	do {
> +		prescale = prescale_next;
> +		if (prescale > OTTO_WDT_PRESCALE_MAX)
> +			return -EINVAL;
> +
> +		tick_ms = otto_wdt_tick_ms(ctrl, prescale);
> +		total_ticks = div_round_ticks(timeout_ms, tick_ms, 2);
> +		phase1_ticks = div_round_ticks(timeout_ms - pretimeout_ms, tick_ms, 1);
> +		phase2_ticks = total_ticks - phase1_ticks;
> +
> +		prescale_next++;
> +	} while (phase1_ticks > OTTO_WDT_PHASE_TICKS_MAX
> +		|| phase2_ticks > OTTO_WDT_PHASE_TICKS_MAX);
> +
> +	v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	v &= ~(OTTO_WDT_CTRL_PRESCALE | OTTO_WDT_CTRL_PHASE1 | OTTO_WDT_CTRL_PHASE2);
> +	v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE1, phase1_ticks - 1);
> +	v |= FIELD_PREP(OTTO_WDT_CTRL_PHASE2, phase2_ticks - 1);
> +	v |= FIELD_PREP(OTTO_WDT_CTRL_PRESCALE, prescale);
> +
> +	iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	timeout_ms = total_ticks * tick_ms;
> +	ctrl->wdev.timeout = timeout_ms / 1000;
> +
> +	pretimeout_ms = phase2_ticks * tick_ms;
> +	ctrl->wdev.pretimeout = pretimeout_ms / 1000;
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_set_timeout(struct watchdog_device *wdev, unsigned int val)
> +{
> +	return otto_wdt_determine_timeouts(wdev, val, min(wdev->pretimeout, val - 1));
> +}
> +
> +static int otto_wdt_set_pretimeout(struct watchdog_device *wdev, unsigned int val)
> +{
> +	return otto_wdt_determine_timeouts(wdev, wdev->timeout, val);
> +}
> +
> +static int otto_wdt_restart(struct watchdog_device *wdev, unsigned long reboot_mode,
> +		void *data)
> +{
> +	struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
> +	u32 reset_mode;
> +	u32 v;
> +
> +	disable_irq(ctrl->irq_phase1);
> +
> +	switch (reboot_mode) {
> +	case REBOOT_SOFT:
> +		reset_mode = OTTO_WDT_MODE_SOFTWARE;
> +		break;
> +	case REBOOT_WARM:
> +		reset_mode = OTTO_WDT_MODE_CPU;
> +		break;
> +	default:
> +		reset_mode = OTTO_WDT_MODE_SOC;
> +		break;
> +	}
> +
> +	/* Configure for shortest timeout and wait for reset to occur */
> +	v = FIELD_PREP(OTTO_WDT_CTRL_RST_MODE, reset_mode) | OTTO_WDT_CTRL_ENABLE;
> +	iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	mdelay(3 * otto_wdt_tick_ms(ctrl, 0));
> +
> +	return 0;
> +}
> +
> +static irqreturn_t otto_wdt_phase1_isr(int irq, void *dev_id)
> +{
> +	struct otto_wdt_ctrl *ctrl = dev_id;
> +
> +	iowrite32(OTTO_WDT_INTR_PHASE_1, ctrl->base + OTTO_WDT_REG_INTR);
> +	dev_crit(ctrl->dev, "phase 1 timeout\n");
> +	watchdog_notify_pretimeout(&ctrl->wdev);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static const struct watchdog_ops otto_wdt_ops = {
> +	.owner = THIS_MODULE,
> +	.start = otto_wdt_start,
> +	.stop = otto_wdt_stop,
> +	.ping = otto_wdt_ping,
> +	.set_timeout = otto_wdt_set_timeout,
> +	.set_pretimeout = otto_wdt_set_pretimeout,
> +	.restart = otto_wdt_restart,
> +};
> +
> +static const struct watchdog_info otto_wdt_info = {
> +	.identity = "Realtek Otto watchdog timer",
> +	.options = WDIOF_KEEPALIVEPING |
> +		WDIOF_MAGICCLOSE |
> +		WDIOF_SETTIMEOUT |
> +		WDIOF_PRETIMEOUT,
> +};
> +
> +static void otto_wdt_clock_action(void *data)
> +{
> +	clk_disable_unprepare(data);
> +}
> +
> +static int otto_wdt_probe_clk(struct otto_wdt_ctrl *ctrl)
> +{
> +	struct clk *clk = devm_clk_get(ctrl->dev, NULL);
> +	int ret;
> +
> +	if (IS_ERR(clk))
> +		return dev_err_probe(ctrl->dev, PTR_ERR(clk), "Failed to get clock\n");
> +
> +	ret = clk_prepare_enable(clk);
> +	if (ret)
> +		return dev_err_probe(ctrl->dev, ret, "Failed to enable clock\n");
> +
> +	ret = devm_add_action_or_reset(ctrl->dev, otto_wdt_clock_action, clk);
> +	if (ret)
> +		return ret;
> +
> +	ctrl->clk_rate_khz = clk_get_rate(clk) / 1000;
> +	if (ctrl->clk_rate_khz == 0)
> +		return dev_err_probe(ctrl->dev, -ENXIO, "Failed to get clock rate\n");
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_probe_reset_mode(struct otto_wdt_ctrl *ctrl)
> +{
> +	static const char *mode_property = "realtek,reset-mode";
> +	const struct fwnode_handle *node = ctrl->dev->fwnode;
> +	int mode_count;
> +	u32 mode;
> +	u32 v;
> +
> +	if (!node)
> +		return -ENXIO;
> +
> +	mode_count = fwnode_property_string_array_count(node, mode_property);
> +	if (mode_count < 0)
> +		return mode_count;
> +	else if (mode_count == 0)
> +		return 0;
> +	else if (mode_count != 1)
> +		return -EINVAL;
> +
> +	if (fwnode_property_match_string(node, mode_property, "soc") == 0)
> +		mode = OTTO_WDT_MODE_SOC;
> +	else if (fwnode_property_match_string(node, mode_property, "cpu") == 0)
> +		mode = OTTO_WDT_MODE_CPU;
> +	else if (fwnode_property_match_string(node, mode_property, "software") == 0)
> +		mode = OTTO_WDT_MODE_SOFTWARE;
> +	else
> +		return -EINVAL;
> +
> +	v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
> +	v &= ~OTTO_WDT_CTRL_RST_MODE;
> +	v |= FIELD_PREP(OTTO_WDT_CTRL_RST_MODE, mode);
> +	iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	return 0;
> +}
> +
> +static int otto_wdt_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct otto_wdt_ctrl *ctrl;
> +	unsigned int max_tick_ms;
> +	int ret;
> +
> +	ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
> +	if (!ctrl)
> +		return -ENOMEM;
> +
> +	ctrl->dev = dev;
> +	ctrl->base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(ctrl->base))
> +		return PTR_ERR(ctrl->base);
> +
> +	/* Clear any old interrupts and reset initial state */
> +	iowrite32(OTTO_WDT_INTR_PHASE_1 | OTTO_WDT_INTR_PHASE_2,
> +			ctrl->base + OTTO_WDT_REG_INTR);
> +	iowrite32(OTTO_WDT_CTRL_DEFAULT, ctrl->base + OTTO_WDT_REG_CTRL);
> +
> +	ret = otto_wdt_probe_clk(ctrl);
> +	if (ret)
> +		return ret;
> +
> +	ctrl->irq_phase1 = platform_get_irq_byname(pdev, "phase1");
> +	if (ctrl->irq_phase1 < 0)
> +		return ctrl->irq_phase1;
> +
> +	ret = devm_request_irq(dev, ctrl->irq_phase1, otto_wdt_phase1_isr, 0,
> +			"realtek-otto-wdt", ctrl);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to get IRQ for phase1\n");
> +
> +	ret = otto_wdt_probe_reset_mode(ctrl);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Invalid reset mode specified\n");
> +
> +	ctrl->wdev.parent = dev;
> +	ctrl->wdev.info = &otto_wdt_info;
> +	ctrl->wdev.ops = &otto_wdt_ops;
> +
> +	/*
> +	 * Since pretimeout cannot be disabled, min. timeout is twice the
> +	 * subsystem resolution. Max. timeout is ca. 43s at a bus clock of 200MHz.
> +	 */
> +	ctrl->wdev.min_timeout = 2;
> +	max_tick_ms = otto_wdt_tick_ms(ctrl, OTTO_WDT_PRESCALE_MAX);
> +	ctrl->wdev.max_hw_heartbeat_ms = max_tick_ms * OTTO_WDT_TIMEOUT_TICKS_MAX;
> +	ctrl->wdev.timeout = min(30U, ctrl->wdev.max_hw_heartbeat_ms / 1000);
> +
> +	watchdog_set_drvdata(&ctrl->wdev, ctrl);
> +	watchdog_init_timeout(&ctrl->wdev, 0, dev);
> +	watchdog_stop_on_reboot(&ctrl->wdev);
> +	watchdog_set_restart_priority(&ctrl->wdev, 128);
> +
> +	ret = otto_wdt_determine_timeouts(&ctrl->wdev, ctrl->wdev.timeout, 1);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to set timeout\n");
> +
> +	return devm_watchdog_register_device(dev, &ctrl->wdev);
> +}
> +
> +static const struct of_device_id otto_wdt_ids[] = {
> +	{ .compatible = "realtek,rtl8380-wdt" },
> +	{ .compatible = "realtek,rtl8390-wdt" },
> +	{ .compatible = "realtek,rtl9300-wdt" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, otto_wdt_ids);
> +
> +static struct platform_driver otto_wdt_driver = {
> +	.probe = otto_wdt_probe,
> +	.driver = {
> +		.name = "realtek-otto-watchdog",
> +		.of_match_table	= otto_wdt_ids,
> +	},
> +};
> +module_platform_driver(otto_wdt_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Sander Vanheule <sander@...nheule.net>");
> +MODULE_DESCRIPTION("Realtek Otto watchdog timer driver");
> 

Powered by blists - more mailing lists