Message-ID: <CAHCN7xKRzxMBmPbDobWTuvNNSpTXk5XENvfBnfkhRY3eZKhn6w@mail.gmail.com>
Date:   Fri, 19 Nov 2021 17:37:18 -0600
From:   Adam Ford <aford173@...il.com>
To:     Nicolas Dufresne <nicolas@...fresne.ca>
Cc:     Tim Harvey <tharvey@...eworks.com>,
        linux-media <linux-media@...r.kernel.org>,
        Schrempf Frieder <frieder.schrempf@...tron.de>,
        Marek Vasut <marek.vasut@...il.com>,
        Jagan Teki <jagan@...rulasolutions.com>,
        Adam Ford-BE <aford@...conembedded.com>,
        cstevens@...conembedded.com,
        Ezequiel Garcia <ezequiel@...guardiasur.com.ar>,
        Philipp Zabel <p.zabel@...gutronix.de>,
        Mauro Carvalho Chehab <mchehab@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Shawn Guo <shawnguo@...nel.org>,
        Sascha Hauer <s.hauer@...gutronix.de>,
        Pengutronix Kernel Team <kernel@...gutronix.de>,
        Fabio Estevam <festevam@...il.com>,
        NXP Linux Team <linux-imx@....com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Heiko Stuebner <heiko@...ech.de>,
        Lucas Stach <l.stach@...gutronix.de>,
        Joakim Zhang <qiangqing.zhang@....com>,
        Alice Guo <alice.guo@....com>, Peng Fan <peng.fan@....com>,
        "open list:HANTRO VPU CODEC DRIVER" 
        <linux-rockchip@...ts.infradead.org>,
        "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
        <devicetree@...r.kernel.org>,
        "moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE" 
        <linux-arm-kernel@...ts.infradead.org>,
        open list <linux-kernel@...r.kernel.org>,
        "open list:STAGING SUBSYSTEM" <linux-staging@...ts.linux.dev>
Subject: Re: [RFC 0/5] arm64: imx8mm: Enable Hantro VPUs

On Fri, Nov 19, 2021 at 10:29 AM Nicolas Dufresne <nicolas@...fresne.ca> wrote:
>
> Hi Adam, Tim,
>
> [...]
> > > > > Nicolas and Adam,
> > > > >
> > > > > For the H1 patches in this series: I've been able to test the IMX8MM
> > > > > H1 JPEG encode using GStreamer 1.18.5:
> > > > > $ gst-inspect-1.0 | grep -e "v4l2.*enc"
> > > > > video4linux2:  v4l2jpegenc: V4L2 JPEG Encoder
> > > > > $ gst-launch-1.0 videotestsrc ! jpegenc ! rtpjpegpay ! udpsink
> > > >                                   ^ v4l2jpegenc
> > > >
> > > > This is just a transcript error ?
> > >
> > > Nicolas,
> > >
> > > No! Thanks for catching my mistake. I was testing with software encode... ooops!
> > >
> > > 'gst-launch-1.0 videotestsrc ! v4l2jpegenc ! fakesink' actually hangs
> > > the board so likely a power-domain issue there?
> >
> > The v4l2-compliance tests fail on the h1 decoder with a hang, but I
> > think we're writing to registers which are not documented in the Mini
> > TRM.  The Mini TRM doesn't explicitly show the JPEG encoding as a
> > feature, but some of the registers state JPEG, but because some of the
> > registers written for the H1 are not documented in the TRM.  If those
> > registers are restricted or not in this SoC, I am concerned that it
> > might be related.  I'll try to run some more tests this weekend to
> > check on the status of the power-domain stuff.
>
> To verify if the HW support JPEG encoding you can read SWREG63 bit 25. This is
> in the TRM, just not labelled properly. To mimic the decoding side, would be "HW
> synthesis config register X" with the bit labelled SW_ENC_JPEG_PROF (but
> PROF/profile is on or off). If your board hang while reading this, you likely
> didn't get the power bit right.
>
> IMX8 has an undocumented control block thing that we have been fighting with in
> imx8q,  perhaps that's your issue. Few driver was proposed, we are still pending
> on NXP solution to be submitted (they asked us to wait, still waiting =)).

Nicolas,

Thanks for the suggestion to read offset FC.  There was an attempt
made by Lucas Stach to develop a VPU blk-ctrl driver to coordinate the
power-domains with the GPC driver. Unfortunately, it does appear to
hang, so it might not be operating correctly.

Lucas,

Do you have any idea of stuff I can try to see if the power domain is
coming online correctly?

[   10.434727] imx-pgc imx-pgc-domain.6: request the vpumix domain to power up
[   10.463647] imx-pgc imx-pgc-domain.6: request the vpumix ADB400 to power up
[   10.517155] imx-pgc imx-pgc-domain.6: genpd vpumix success
[   10.728927] vpu: set fuse bits to enable
[   10.825500] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-g1 GPC domain
[   10.878986] imx-pgc imx-pgc-domain.7: request the vpu-g1 domain to power up
[   10.932429] imx-pgc imx-pgc-domain.7: genpd vpu-g1 success
[   10.971988] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-g1 success
[   11.004726] hantro-vpu 38300000.video-codec: registered
nxp,imx8mm-vpu-dec as /dev/video0
[   11.040760] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-g2 GPC domain
[   11.066181] imx-pgc imx-pgc-domain.8: request the vpu-g2 domain to power up
[   11.087887] imx-pgc imx-pgc-domain.8: genpd vpu-g2 success
[   11.113808] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-g2 success
[   11.139634] hantro-vpu 38310000.video-codec: registered
nxp,imx8mm-vpu-g2-dec as /dev/video1
[   11.156463] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-h1 GPC domain
[   11.170817] imx-pgc imx-pgc-domain.9: request the vpu-h1 domain to power up
[   11.232990] imx-pgc imx-pgc-domain.9: genpd vpu-h1 success
[   11.252546] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-h1 success
[   11.266152] hantro-vpu 38320000.video-codec: Checking vpu->enc_base + 0xfc

<hang>

adam

>
> > >
> > > >
> > > > > host=192.168.1.146 port=5000
> > > > > viewed on client@....168.1.146 via:
> > > > > $ gst-launch-1.0 udpsrc port=5000 ! application/x-rtp,payload=96 !
> > > > > rtpjpegdepay ! jpegdec ! autovideosink
> > > > >
> > > > > For the G1/G2 patches in the series I don't see any Gstreamer
> > > > > 'v4l2.*dec' elements. Perhaps I need a newer version of Gstreamer.
> > > >
> > > > Most likely yes, I suggest building gstreamer/ branch "main", GStreamer has now
> > > > a single repository. We are very close to 1.20, which will include stable API
> > > > support of H264, MPEG2 and VP8 decoding.
> > > >
> > >
> > > Ok, let me see if I can navigate through the build process and I'll
> > > get back to you.
> > >
> > > Thanks,
> > >
> > > Tim
> > >
> > > > >
> > > > > I have CSI capture and DSI display currently working on
> > > > > imx8mm-venice-gw73xx-0x that I can play with. The CSI sensor only
> > > > > supports RAW8/RAW10 (and gstreamer currently only supports RAW8) and I
> > > > > can't efficiently convert to something the JPEG encoder likes without
> > > > > bayer2rgbneon (a libneon version).
> > > > >
> > > > > I see from the IMX8MMRM that the 2D GPU supports scaling etc with a
> > > > > wide range of data formats but I'm not sure how to tap into this as
> > > > > that hardware is managed by the vivante driver. On the IMX6QDL there
> > > > > is a separate IPU block that Philipp Zabel wrote a nice mem2mem
> > > > > csc/scaler driver for but I don't see any equivalent currently for
> > > > > IMX8MM.
> > > > >
> > > > > Best regards,
> > > > >
> > > > > Tim
> > > >
>

Powered by blists - more mailing lists